Download Print this page

Advertisement

Oper ator ' s manual Manual d'utalisation Manual de instrucciones
Hedge Trimmer Attachment HA110 HA850
Complément Taille-haie HA110 HA850
Tijeras cortasetos (suplemento) HA110 HA850
G G G G B B B B F F F F R R R R E E E E S S S S

Advertisement

   Also See for Husqvarna HA110

   Related Manuals for Husqvarna HA110

   Summary of Contents for Husqvarna HA110

  • Page 1

    Oper ator ′ s manual Manual d’utalisation Manual de instrucciones Hedge Trimmer Attachment HA110 HA850 Complément Taille-haie HA110 HA850 Tijeras cortasetos (suplemento) HA110 HA850 G G G G B B B B F F F F R R R R E E E E S S S S...

  • Page 2: Key To Symbols

    KEY T O SYMBOLS Symbols Other symbols/decals on the mac hine refer to special certification requirements for certain markets. W ARNING! Incorrect or careless use of a The engine is s witched off by moving the stop hedge trimmer can turn it into a dangerous switch to the stop position.

  • Page 3: Table Of Contents

    Note the following before starting: ........ WHA T IS WHAT? Husqvarna AB has a policy of continuous product What is what on the hedge tr immer attachment? ..development and therefore reserves the right to modify the design and appearance of products without prior notice.

  • Page 4: Wha T Is What

    WHA T IS WHA T? What is what on the hedg e trimmer attachment? 1 Cutter 7 Hand guard (HA 110) 2 Grease nipple and plug for filling lubricant. 8 Operator ′ s manual 3 Bevel gear 9 Transport guard 4 Front handle 10 Shaft coupling 5 Hand guard mounting screw...

  • Page 5: Safety Instr Uctions

    SAFETY INSTR UCTIONS Mac hine ′ ′ ′ ′ s safety equipment Blades This section descr ibes the machine ′ s safety equipment, its purpose, and how checks and maintenance should be carried out to ensure that it operates correctly. See the ”What is T o ensure good cutting results it is important that the contact what?”...

  • Page 6: Assembl Y

    ASSEMBL Y Fitting the hand guar d and loop Fitting the cutting head handle (HA 110) It is impor tant that the hedge trimmer is laid on a flat surface when you fit the cutting head. Otherwise the cutting head may not be fitted straight.

  • Page 7: St Arting And Stopping

    ST AR TING AND ST OPPING Chec k before starting • Inspect the working area. Remove any objects that could be thrown out. • Check the cutting attachment. Never use blades that are dull, cracked or damaged. • Check that the machine is in perfect working order. Check that all nuts and screws are tight.

  • Page 8: W Orking Techniques

    W ORKING TECHNIQ UES General w orking instructions Saf ety instructions while working IMPORTANT! This section takes up the basic safety precautions for • Always ensure you have a safe and stable working working with a hedge trimmer. position. If you encounter a situation where you are uncertain how to •...

  • Page 9: Basic Working Techniques

    WORKING TECHNIQUES • Always wear heavy-duty gloves when repairing the cutting 2 Press the cutting unit against the hedge or some other attachment. This is extremely sharp and can easily cause firm surface until the required angle is set. cuts. •...

  • Page 10: Maintenance

    first filled with grease after approximately 20 hours of operation, and subsequently approximately every 60 hours of operation. Use Husqvarna’s special grease, no. 503 98 96-01. 1 Check that the blades do not move when the engine is idling or when the choke is in the start throttle position.

  • Page 11

    1150040-20 ´®z+R$"¶0F¨ ´®z+R$"¶0F¨ 2005-07-07...

This manual also for:

Ha850

Comments to this Manuals

Symbols: 0
Latest comments: