Page 3
Yamaha has met these standards without reducing the performance or economy of operation of the motorcycle. To maintain these high standards, it is important that you and your Yamaha dealer pay close attention to the recommended maintenance schedules and operating instructions contained within this manual.
This manual should be considered a permanent part of this motorcycle and should remain with it even if the motorcycle is subsequently sold. Yamaha continually seeks advancements in product design and quality. Therefore, while this manual contains the most current product information available at the time of printing, there may be minor discrepancies between your motorcycle and this manual.
Page 5
IMPORTANT MANUAL INFORMATION AND UNTIL YOU HAVE BEEN TRAINED IN SAFE AND PROPER RIDING TECHNIQUES. REGULAR INSPECTIONS AND CAREFUL MAINTENANCE, ALONG WITH GOOD RIDING SKILLS, WILL ENSURE THAT YOU SAFELY ENJOY THE CAPABILITIES AND THE RELIABILITY OF THIS MOTORCYCLE. *Product and specifications are subject to change without notice.
TABLE OF CONTENTS SAFETY INFORMATION ....1-1 Opening and closing Canister (for California only) ..6-10 Location of important labels ...1-5 the cowlings ......3-22 Engine oil and oil filter cartridge ... 6-11 Rear view mirrors ......3-23 Final gear oil ......... 6-14 DESCRIPTION ........2-1 Adjusting the front fork ....
Page 8
TABLE OF CONTENTS Checking and lubricating the YAMAHA MOTOR CORPORATION, centerstand and sidestand ..6-26 U.S.A. STREET AND ENDURO Lubricating the swingarm pivots ...6-27 MOTORCYCLE LIMITED Lubricating the rear suspension ...6-27 WARRANTY ....... 9-7 Checking the front fork ....6-27 YAMAHA EXTENDED SERVICE Checking the steering ....6-28...
SAFETY INFORMATION EAU10281 AND/OR WHEN MADE NECES- • Ride where other motorists can SARY BY MECHANICAL CONDI- see you. Avoid riding in another MOTORCYCLES SINGLE TIONS. motorist’s blind spot. TRACK VEHICLES. THEIR SAFE USE Many accidents involve inexperi- AND OPERATION ARE DEPENDENT Safe riding enced operators.
Page 10
Modifications made to this motorcycle other motorists can see you. the single most critical factor in the pre- not approved by Yamaha, or the re- The posture of the operator and vention or reduction of head injuries. moval of original equipment, may ren- passenger is important for proper Always wear an approved helmet.
Page 11
Maximum load: been specifically designed for use on create instability due to improper FJR1300AEX 208 kg (459 lb) this motorcycle. Since Yamaha cannot weight distribution or aerody- FJR1300AEXC 207 kg (456 lb) test all other accessories that may be namic changes. If accessories...
Page 12
SAFETY INFORMATION tor and may limit control ability, Always turn the engine off before or clothing, immediately wash the therefore, such accessories are leaving the motorcycle unattended affected area with soap and water not recommended. and remove the key from the main and change your clothes.
Main switch/steering lock This is not an automatic transmission, This vehicle features the YCC-S only the clutch system is automatic. (Yamaha Chip Controlled-Shift) sys- The gears must be shifted by the rider. tem. The basic function of this system allows the rider to shift gears without the use of a clutch lever.
INSTRUMENT AND CONTROL FUNCTIONS EAU10660 To unlock the steering EAU11003 Indicator and warning lights All electrical systems are off. The key can be removed. EAU10690 LOCK The steering is locked, and all electrical systems are off. The key can be re- moved.
Page 21
Stop the vehicle when it is safe to do so, Even if the oil level is sufficient, the have a Yamaha dealer check the self- and park it away from traffic. Have a warning light may flicker when riding on diagnosis system.
Place the vehicle on the centerstand, while riding, the ABS may be defective. then while rotating the rear wheel, push If this occurs, have a Yamaha dealer the shift pedal rod and pivot forward un- til the transmission is in the neutral po- check the system as soon as possible.
INSTRUMENT AND CONTROL FUNCTIONS EAU11872 EAU40851 a fuel reserve tripmeter (which Tachometer Multi-function display shows the distance traveled on the fuel reserve) a clock a fuel meter a coolant temperature meter a transmission gear display an ambient temperature display a fuel consumption display (instan- taneous and average consumption functions) a self-diagnosis device...
Page 24
INSTRUMENT AND CONTROL FUNCTIONS Odometer and tripmeter modes distance traveled from that point. In that Clock case, pushing the “SELECT” button switches the display between the vari- ous tripmeter and odometer modes in the following order: F-TRIP → ODO → TRIP 1 → TRIP 2 → F-TRIP To reset a tripmeter, select it by push- ing the “SELECT”...
Page 25
INSTRUMENT AND CONTROL FUNCTIONS Fuel meter will start flashing. If this occurs, have a ECA10020 CAUTION: Yamaha dealer check the electrical cir- cuit. Do not operate the engine if it is overheated. Coolant temperature meter Transmission gear display 1. Fuel meter The fuel meter indicates the amount of fuel in the fuel tank.
Page 26
INSTRUMENT AND CONTROL FUNCTIONS Ambient temperature, instanta- Ambient temperature mode 20 km/h (12.5 mi/h)] or when neous fuel consumption and aver- stopped at traffic signals, railroad age fuel consumption modes crossings, etc. Instantaneous fuel consumption mode 1. Ambient temperature This display shows the ambient tem- 1.
Page 27
If the multi-function display indicates consumption display, “_ _._” will such an error code, note the code num- be shown for that display until the ber, and then have a Yamaha dealer vehicle has traveled 1 km (0.6 mi). check the vehicle. ECA11790...
INSTRUMENT AND CONTROL FUNCTIONS EAU12347 Right EAU12493 Handlebar switches Windshield position adjusting switch “ ” Left To move the windshield up, push this switch in direction (a). To move the windshield down, push the switch in di- rection (b). 1. Engine stop switch “ ”...
Page 29
INSTRUMENT AND CONTROL FUNCTIONS EAU12660 EAU12765 EAU40381 Engine stop switch “ ” Hazard switch “ ” Hand shift control switch Set this switch to “ ” before starting With the key in the “ON” position, use the engine. Set this switch to “ ”...
INSTRUMENT AND CONTROL FUNCTIONS and release this switch after start- EAU40492 Shift pedal ing the engine to enable hand shifting. 1. Shift pedal 2. Bolt 1. Shift pedal 3. Standard position This vehicle is equipped with a con- 2. Move the shift pedal to the desired stant-mesh 5-speed transmission.
INSTRUMENT AND CONTROL FUNCTIONS EAU40481 EAU26823 EAU39540 Hand shift lever “ ”/“ ” Brake lever Brake pedal The brake lever is located at the right handlebar grip. To apply the front brake, pull the lever toward the handle- bar grip. 1.
INSTRUMENT AND CONTROL FUNCTIONS EAU39531 al are even slightly applied, a vi- bration can be felt at the lever and The Yamaha ABS (Anti-lock Brake pedal, but these do not indicate a System) features a dual electronic con- malfunction. trol system, which acts on the front and When the ABS is activated, the rear brakes independently.
INSTRUMENT AND CONTROL FUNCTIONS EAU13072 EAU13220 Fuel tank cap NOTE: Fuel The fuel tank cap cannot be closed un- less the key is in the lock. In addition, the key cannot be removed if the cap is not properly closed and locked. EWA11090 WARNING Make sure that the fuel tank cap is...
UNLEADED GASOLINE ONLY CAUTION: containing methanol is not recom- Fuel tank capacity: mended by Yamaha because it can The following precautions must be 25.0 L (6.61 US gal) (5.50 Imp.gal) cause damage to the fuel system or ve- observed to prevent a fire hazard or Fuel reserve amount: hicle performance problems.
INSTRUMENT AND CONTROL FUNCTIONS EAU39492 To install the passenger seat Seats 1. Insert the projections on the rear of the passenger seat into the seat Passenger seat holders as shown, and then push the front of the seat down to lock it To remove the passenger seat in place.
INSTRUMENT AND CONTROL FUNCTIONS 2. Install the passenger seat. EAU39632 Adjusting the rider seat height NOTE: The rider seat height can be adjusted to Make sure that the seats are prop- one of two positions to suit the rider’s erly secured before riding. preference.
Page 37
INSTRUMENT AND CONTROL FUNCTIONS 6. Align the projection on the bottom of the rider seat with the “H” posi- tion slot, and then push the rear of the seat down to lock it in place as shown. 1. Rider seat height position adjuster 1.
INSTRUMENT AND CONTROL FUNCTIONS 6. Align the projection on the bottom EAU14461 EAU39480 Storage compartment Accessory box of the rider seat with the “L” posi- The accessory box is located beside tion slot, and then push the rear of the meter panel. the seat down to lock it in place as shown.
The headlight beam adjusting knobs Do not place heat-sensitive items in erence. Have a Yamaha dealer adjust are used to raise or lower the height of the accessory box. The accessory the position of the handlebars.
INSTRUMENT AND CONTROL FUNCTIONS EAU39621 Opening and closing the cowl- ings The cowlings can be tilted back 30 mm (1.18 in) for added ventilation to suit the riding conditions. 1. Quick fastener screw 1. Quick fastener screw 2. Pull the cowling to the open posi- 2.
INSTRUMENT AND CONTROL FUNCTIONS EAU39671 EAU14731 load thereby soften Rear view mirrors Adjusting the front fork suspension, turn the adjusting bolt on The rear view mirrors of this vehicle can This front fork is equipped with spring each fork leg in direction (b). be folded forward or backward for park- preload adjusting bolts, rebound damp- NOTE:...
Page 42
INSTRUMENT AND CONTROL FUNCTIONS Rebound damping force Compression damping force ECA10100 CAUTION: Never attempt to turn an adjusting mechanism beyond the maximum or minimum settings. NOTE: Although the total number of clicks of a damping force adjusting mechanism may not exactly match the above spec- ifications due to small differences in 1.
INSTRUMENT AND CONTROL FUNCTIONS EAU14911 For riding solo, move the spring preload Rebound damping setting: Adjusting the shock absorber adjusting lever in direction (b). For Minimum (soft): assembly riding with a passenger, move the 20 click(s) in direction (b)* This shock absorber assembly is Standard: spring preload adjusting lever in direc- 12 click(s) in direction (b)*...
INSTRUMENT AND CONTROL FUNCTIONS EAU15301 below and have a Yamaha dealer re- EAU40522 Sidestand Ignition circuit cut-off system pair it if it does not function proper- The sidestand is located on the left side The ignition circuit cut-off system (com- of the frame.
Page 46
The vehicle should not be ridden until With the engine still running: checked by a Yamaha dealer. 7. Move the sidestand up. 8. Keep the front or rear brake applied. 9. Shift the transmission into gear.
INSTRUMENT AND CONTROL FUNCTIONS EAU39651 EWA14360 Auxiliary DC jack WARNING This vehicle is equipped with an auxilia- To prevent electrical shock or short- ry DC jack in the accessory box. circuiting, make sure that the cap is A 12-V accessory connected to the installed when the auxiliary DC jack auxiliary jack can be used when the key is not being used.
PRE-OPERATION CHECKS EAU15593 The condition of a vehicle is the owner’s responsibility. Vital components can start to deteriorate quickly and unexpectedly, even if the vehicle remains unused (for example, as a result of exposure to the elements). Any damage, fluid leakage or loss of tire air pressure could have serious consequences.
• If necessary, add recommended coolant to specified level. 6-15 • Check cooling system for leakage. • Check operation. • If soft or spongy, have Yamaha dealer bleed hydraulic system. • Check brake pads for wear. Front brake • Replace if necessary.
Page 50
• Make sure that operation is smooth. • Check cable free play. Throttle grip 6-17, 6-25 • If necessary, have Yamaha dealer adjust cable free play and lubricate cable and grip housing. • Make sure that operation is smooth. Control cables 6-25 •...
NOTE: When the transmission is in the neutral position, the neutral indicator light should be on, otherwise have a Yamaha dealer check the electrical cir- cuit. 3. Start the engine by pushing the 1. Hand shift lever start switch.
Page 53
OPERATION AND IMPORTANT RIDING POINTS The gears can be shifted using either Always return the throttle to the 5. Shift into second gear and release the shift pedal or the hand shift lever. closed position while changing the shift pedal. The hand shift lever has to be enabled gears to avoid damaging the en- 6.
3rd → 4th: 40 km/h (25 mi/h) period, immediately have a 4th → 5th: 50 km/h (31 mi/h) Yamaha dealer check the vehi- Shift down points: EAU17121 5th → 4th: 25 km/h (15.5 mi/h) cle.
OPERATION AND IMPORTANT RIDING POINTS EAU40581 Do not park on a slope or on soft Parking ground, otherwise the vehicle When parking, stop the engine by turn- may overturn. ing the main switch to “OFF”, and then ECA10380 remove the key. CAUTION: NOTE: Never park in an area where there...
TRAINED AND EQUIPPED TO PER- certain maintenance work correctly. FORM THESE PARTICULAR SER- VICES. NOTE: If you do not have the tools or experi- ence required for a particular job, have a Yamaha dealer perform it for you.
Page 57
PERIODIC MAINTENANCE AND MINOR REPAIR EWA10340 WARNING Modifications approved Yamaha may cause loss of perfor- mance, excessive emissions, and render the vehicle unsafe for use. Consult a Yamaha dealer before at- tempting any changes.
• Check the air cut-off valve, reed Air induction sys- √ √ valve, and hose for damage. • Replace any damaged parts. * Since these items require special tools, data and technical skills, have a Yamaha dealer perform the service.
PERIODIC MAINTENANCE AND MINOR REPAIR EAU32185 General maintenance and lubrication chart INITIAL ODOMETER READINGS 600 mi 4000 mi 8000 mi 12000 mi 16000 mi 20000 mi ITEM ROUTINE (1000 km) (7000 km) (13000 km) (19000 km) (25000 km) (31000 km) 1 month 6 months 12 months...
Page 60
PERIODIC MAINTENANCE AND MINOR REPAIR INITIAL ODOMETER READINGS 600 mi 4000 mi 8000 mi 12000 mi 16000 mi 20000 mi ITEM ROUTINE (1000 km) (7000 km) (13000 km) (19000 km) (25000 km) (31000 km) 1 month 6 months 12 months 18 months 24 months 30 months...
Page 61
Front and rear brake √ √ √ √ √ √ 24 * • Check operation. switches • Apply Yamaha chain and cable √ √ √ √ √ √ 25 * Control cables lube or engine oil SAE 10W-30 thoroughly.
Page 62
• Adjust headlight beam. * Since these items require special tools, data and technical skills, have a Yamaha dealer perform the service. NOTE: From 24000 mi (37000 km) or 36 months, repeat the maintenance intervals starting from 8000 mi (13000 km) or 12 months.
PERIODIC MAINTENANCE AND MINOR REPAIR EAU18771 Removing and installing pan- The panels shown need to be removed to perform some of the maintenance jobs described in this chapter. Refer to this section each time a panel needs to be removed and installed. 1.
Do not attempt to diagnose such problems yourself. Instead, have a Yamaha dealer check the vehicle. 1. Panel C If a spark plug shows signs of electrode 2. Bolt erosion and excessive carbon or other 3.
PERIODIC MAINTENANCE AND MINOR REPAIR EAU19681 Specified spark plug: Tightening torque: Canister (for California only) NGK/CR8E Spark plug: DENSO/U24ESR-N 12.5 Nm (1.25 m·kgf, 9.0 ft·lbf) Before installing a spark plug, the spark NOTE: plug gap should be measured with a If a torque wrench is not available when wire thickness gauge and, if necessary, installing a spark plug, a good estimate...
PERIODIC MAINTENANCE AND MINOR REPAIR EAU19883 2. Start the engine, warm it up for Engine oil and oil filter car- NOTE: several minutes, and then turn it The engine oil should be between the tridge off. minimum and maximum level marks. The engine oil level should be checked 3.
Page 67
An oil filter wrench is available at a seated. 43 Nm (4.3 m·kgf, 31 ft·lbf) Yamaha dealer. 7. Install the new oil filter cartridge, 9. Refill with the specified amount of 6. Apply a thin coat of engine oil to...
Page 68
After the engine is started, the engine oil level warning light should go off if the oil level is sufficient. ECA10400 CAUTION: If the oil level warning light flickers or remains on, immediately turn the engine off and have a Yamaha dealer check the vehicle. 6-13...
23 Nm (2.3 m·kgf, 17 ft·lbf) for oil leakage before each ride. If any NOTE: leakage is found, have a Yamaha deal- To change the final gear oil The oil level should be at the brim of the er check and repair the vehicle. In addi- 1.
PERIODIC MAINTENANCE AND MINOR REPAIR 6. Install the oil filler bolt, and then EAU20070 Coolant NOTE: tighten it to the specified torque. The coolant should be between the The coolant level should be checked minimum and maximum level marks. before each ride. In addition, the cool- Tightening torque: ant must be changed at the intervals Final gear oil filler bolt:...
Page 71
Have a If water has been added to the Yamaha dealer change the coolant. coolant, have a Yamaha dealer check the antifreeze content of the coolant as soon as possible, otherwise the effectiveness of the coolant will be reduced.
Have a Yamaha dealer adjusted by a Yamaha dealer at the in- clean and replace the air filter element. tervals specified in the periodic mainte- nance and lubrication chart.
Rear: from occurring, the valve clearance regarding the specified tires. 290 kPa (42 psi) (2.90 kgf/cm²) must be adjusted by a Yamaha dealer FJR1300AEX 90–208 kg (198–459 at the intervals specified in the periodic Tire air pressure maintenance and lubrication chart.
Page 74
(minimum tread depth), if the tire has a nail or glass fragments in it, or if the sidewall is cracked, con- tact a Yamaha dealer immediately and have the tire replaced. Minimum tire tread depth (front and rear): 1.0 mm (0.04 in)
Page 75
BRIDGESTONE/BT021R F tires listed below have been ap- FRONT and REAR: proved this model Tire air valve: Yamaha Motor Co., Ltd. TR412 Valve core: Always make sure that the valve #9100 (original) caps are securely installed to prevent air pressure leakage.
The accessories or replacement fore each ride. If any damage is parts you choose for your vehicle found, have a Yamaha dealer re- should be designed specifically for place the wheel. Do not attempt this model, and they must be se-...
If ified in the periodic maintenance and before each ride. If the YCC-S clutch necessary, have a Yamaha dealer ad- lubrication chart. plates wear out, shifting becomes just the brake light switch.
PERIODIC MAINTENANCE AND MINOR REPAIR cator groove has almost disappeared, EAU40591 YCC-S clutch Checking the brake and have a Yamaha dealer replace the YCC-S clutch fluid levels brake pads as a set. Front brake EAU22500 Rear brake pads 1. Minimum level mark...
YCC-S clutch fluids 6-8.) stalling them. Have a Yamaha dealer change the Be careful that water or dust does Observe these precautions: brake and YCC-S clutch fluids at the in- not enter the brake and YCC-S...
If a cable is damaged maintenance chart. or does not move smoothly, have a Yamaha dealer check or replace it. Recommended lubricant: Yamaha Chain and Cable Lube or engine oil SAE 10W-30...
Recommended lubricant: EWA10740 Silicone grease WARNING If the centerstand or sidestand does not move up and down smoothly, have a Yamaha dealer check or re- pair it. Recommended lubricant: Lithium-soap-based grease 6-26...
PERIODIC MAINTENANCE AND MINOR REPAIR EAUM1650 EAU23250 EAU23271 Lubricating the swingarm piv- Lubricating the rear suspen- Checking the front fork sion The condition and operation of the front fork must be checked as follows at the intervals specified in the periodic main- tenance and lubrication chart.
Securely support the vehicle so that fork does not operate smoothly, there is no danger of it falling over. have a Yamaha dealer check or re- pair it. 2. Hold the lower ends of the front fork legs and try to move them for- ward and backward.
Batteries produce explosive hy- To charge the battery drogen gas. Therefore, keep Have a Yamaha dealer charge the bat- sparks, flames, cigarettes, etc., tery as soon as possible if it seems to away from the battery and pro- have discharged.
The main fuse, the fuse boxes and the CHILDREN. sealed-type (MF) battery charg- ABS motor fuse are located under pan- er, have a Yamaha dealer el A. (See page 6-8.) charge your battery. To store the battery 1. If the vehicle will not be used for...
Page 86
2. Right radiator fan fuse 10.0 A 4. If the fuse immediately blows Hazard fuse: 3. Left radiator fan fuse again, have a Yamaha dealer 10.0 A 4. Hazard fuse check the electrical system. Fuel injection system fuse: 5. Backup fuse (for odometer and clock) 15.0 A...
If a front turn signal light does not come light bulb or a tail/brake light Yamaha dealer check its electrical cir- on, have a Yamaha dealer check its bulb cuit or replace the bulb. electrical circuit or replace the bulb.
PERIODIC MAINTENANCE AND MINOR REPAIR 6. Install the passenger seat. EAU24310 3. Remove the defective bulb by pull- Replacing the license plate ing it out. light bulb 4. Insert a new bulb into the socket. 1. Remove the license plate light unit 5.
The following troubleshooting charts represent quick and easy procedures for checking these vital systems your- self. However, should your motorcycle require any repair, take it to a Yamaha dealer, whose skilled technicians have the necessary tools, experience, and know-how to service the motorcycle properly.
Remove the spark plugs and check the electrodes. The engine does not start. Have a Yamaha dealer check the vehicle. Check the battery. 4. Battery The engine turns over The battery is good.
Page 91
Start the engine. If the engine overheats again, have a The coolant level Yamaha dealer check and repair the cooling system. is OK. NOTE: If coolant is not available, tap water can be temporarily used instead, provided that it is changed to the recommended coolant as soon as possible.
Rust and corrosion can develop matte colored finished parts. Be ECA10771 even if high-quality components are sure to consult a Yamaha dealer for CAUTION: advice on what products to use be- used. A rusty exhaust pipe may go un- Avoid using strong acidic wheel fore cleaning the vehicle.
Page 93
MOTORCYCLE CARE AND STORAGE cleaning products, solvent or After normal use ECA10790 CAUTION: thinner, fuel (gasoline), rust re- Remove dirt with warm water, a mild movers or inhibitors, brake flu- detergent, and a soft, clean sponge, Do not use warm water since it in- id, antifreeze or electrolyte.
7. Let the motorcycle dry completely Always store your motorcycle in a cool, NOTE: before storing or covering it. dry place and, if necessary, protect it Consult a Yamaha dealer for advice on EWA11130 against dust with a porous cover. WARNING what products to use.
Page 95
MOTORCYCLE CARE AND STORAGE 3. Perform the following steps to pro- 4. Lubricate all control cables and the tect the cylinders, piston rings, etc. pivoting points of all levers and from corrosion. pedals as well as of the side- a. Remove the spark plug caps stand/centerstand.
SPECIFICATIONS Dimensions: Engine oil: Fuel injection: Overall length: Type: Throttle body: 2230 mm (87.8 in) YAMALUBE 4 (20W-40) or SAE 20W-40 Manufacturer: Overall width: Recommended engine oil grade: MIKUNI 750 mm (29.5 in) API service SG type or higher, JASO Type/quantity: Overall height: standard MA...
Page 97
SPECIFICATIONS 3rd: Loading: Rim size: 31/23 (1.348) 17M/C x MT5.50 Maximum load: 4th: Front brake: FJR1300AEX 208 kg (459 lb) 28/26 (1.077) FJR1300AEXC 207 kg (456 lb) Type: 5th: (Total weight of rider, passenger, cargo and Dual disc brake 26/28 (0.929) accessories) Operation: Chassis:...
Page 98
SPECIFICATIONS Charging system: ABS warning light: AC magneto Battery: Fuses: Model: Main fuse: GT14B-4 50.0 A Voltage, capacity: Headlight fuse: 12 V, 12.0 Ah 25.0 A Headlight: Signaling system fuse: 15.0 A Bulb type: Ignition fuse: Halogen bulb Bulb voltage, wattage × quantity: 10.0 A Radiator fan fuse: Headlight:...
Record the key identification number, vehicle identification number and mod- el label information in the spaces pro- vided below for assistance when ordering spare parts from a Yamaha dealer or for reference in case the vehi- cle is stolen. KEY IDENTIFICATION NUMBER: 1.
Page 100
The model label is affixed to the frame under the passenger seat. (See page 3-17.) Record the information on this la- bel in the space provided. This informa- tion will be needed when ordering spare parts from a Yamaha dealer.
If you believe that your vehicle has a defect which could cause a crash or could cause injury or death, you should immediately inform the National Highway Traffic Safety Administration (NHTSA) in addition to notifying Yamaha Motor Corporation, U.S.A. If NHTSA receives similar complaints, it may open an investigation, and if it finds that a safety defect exists in a group of vehicles, it may order a recall and remedy campaign.
CONSUMER INFORMATION EAU26560 Motorcycle noise regulation TAMPERING WITH NOISE CONTROL SYSTEM PROHIBITED: Federal law prohibits the following acts or the causing thereof: (1) The removal or rendering inoperative by any person other than for purposes of maintenance, repair, or replacement of any device or element of design incorporated into any new ve- hicle for the purpose of noise control prior to its sale or delivery to the ultimate purchaser or while it is in use or (2) the use of the vehicle after such device or element of design has been removed or rendered inoperative by any person.
CONSUMER INFORMATION EAU26632 Maintenance record Copies of work orders and/or receipts for parts purchased and installed on your vehicle will be required to document that maintenance has been completed in accordance with the emissions warranty. The chart below is printed only as a reminder that maintenance work is required.
Page 104
CONSUMER INFORMATION Maintenance Date of Servicing dealer Mileage Remarks interval service name and address 36000 mi (55000 km) or 54 months 40000 mi (61000 km) or 60 months...
CONSUMER INFORMATION EAU26663 YAMAHA MOTOR CORPORATION, U.S.A. STREET AND ENDURO MOTORCYCLE LIMITED WARRANTY Yamaha Motor Corporation, U.S.A. hereby warrants that CUSTOMER’S RESPONSIBILITY under this Engine new Yamaha motorcycles will be free from defects in warranty shall be to: Displacement Period...
Page 106
CUSTOMER SERVICE What costs are my responsibility during the warranty period? If your machine requires warranty service, you must take it to any authorized Yamaha The customer’s responsibility includes all costs of normal maintenance services, motorcycle dealer within the continental United States. Be sure to bring your warranty non-warranty repairs, accident and collision damages, and oil, oil filters, air filters, registration card or other valid proof of the original date of purchase.
This excellent Y.E.S. plan coverage is only available to dealer to see how comforting uninterrupted factory- Yamaha owners like you, and only while your Yamaha is still backed protection can be. within the Yamaha Limited Warranty period. So visit your authorized Yamaha dealer to get all the facts.
Page 108
Yamaha Limited Warranty expires. A special note: If visiting your dealer isn’t convenient, contact Yamaha with your Primary ID number (your frame number). We’ll be happy to help you get the Y.E.S. coverage you need.
Page 109
INDEX Engine trouble/YCC-S indicators and Maintenance and lubrication, periodic ..6-4 warning light..........3-3 Maintenance, emission control system ... 6-3 ABS ............3-14 Maintenance, periodic......6-1 ABS warning light ........3-4 Maintenance record ........ 9-5 Accessories and replacement parts ..6-21 Final gear oil..........6-14 Matte color, caution ........