Download Print this page

Makita LS1016 Instruction Manual page 19

Slide compound miter saw
Hide thumbs Also See for LS1016:

Advertisement

Available languages
  • EN

Available languages

  • ENGLISH, page 1
Sliding the fences to inside by loosening the clamping
screw only before miter-cutting allows support of work-
piece close to the saw blade. (Fig. 33 & 34)
To adjust the fences before bevel-cutting, loosen a lever
and slide the upper fence outward. Make a dry run with
the saw turned off and check clearance. (Fig. 35)
Adjust the fence to be as close to the blade as practical
to provide maximum workpiece support, without interfer-
ing with arm up and down movement. Tighten lever
securely. When the bevel operations are complete, don't
forget to relocate the fence.
NOTE:
• For easy tightening/loosening, the position of the lever
can be changed according to your need by pulling it up.
Vertical vise (Fig. 36)
The vertical vise can be installed in two positions on
either the left or right side of the base. Insert the vise rod
into the hole in the base.
Position the vise arm according to the thickness and
shape of the workpiece and secure the vise arm by tight-
ening the screw. If the screw to secure the vise arm con-
tacts the carriage, install the screw on the opposite side
of vise arm. Make sure that no part of the tool contacts
the vise when lowering the handle fully and pulling or
pushing the carriage all the way. If some part contacts
the vise, re-position the vise.
Press the workpiece flat against the guide fence and the
turn base. Position the workpiece at the desired cutting
position and secure it firmly by tightening the vise knob.
Turning the vise knob to 90° counterclockwise allows the
vise knob to be moved up and down, facilitating the quick
setting of workpiece. To secure the workpiece after set-
ting, turn it the vise knob clockwise.
CAUTION:
• The workpiece must be secured firmly against the turn
base and guide fence with the vise during all opera-
tions.
Horizontal vise (optional accessory) (Fig. 37 & 38)
The horizontal vise can be installed in two positions on
either the left or right side of the base. When performing
15° or greater miter cuts, install the horizontal vise on the
side opposite the direction in which the turn base is to be
turned.
By flipping the vise nut to the left, the vise is released,
and rapidly moves in and out. To grip the workpiece,
push the vise knob forward until the vise plate contacts
the workpiece and flip the vise nut to the right. Then turn
the vise knob clockwise to secure the workpiece.
The maximum width of workpiece which can be secured
by the horizontal vise is 215 mm.
CAUTION:
• Always set the vice nut to the right fully when securing
the workpiece. Failure to do so may result in insufficient
securing of the workpiece. This could cause the work-
piece to be thrown, cause damage to the blade or
cause the loss of control, which can result in PER-
SONAL INJURY.
• When cutting out thin workpiece, such as base boards,
against the fence, always use the horizontal vise.
Holders (optional accessory) (Fig. 39)
The holders can be installed on either side as a conve-
nient means of holding workpieces horizontally. Slip the
holder rods into the holes in the base and adjust their
length according to the workpiece to be held. Then
tighten the holders securely with the screws.
CAUTION:
• Always support long workpieces level with the top sur-
face of the turn base for accurate cuts and to prevent
dangerous loss of control of the tool.
OPERATION
CAUTION:
• Before use, be sure to release the handle from the low-
ered position by pulling the stopper pin.
• Make sure the blade is not contacting the workpiece,
etc. before the switch is turned on.
• Do not apply excessive pressure on the handle when
cutting. Too much force may result in overload of the
motor and/or decreased cutting efficiency. Push down
handle with only as much force as is necessary for
smooth cutting and without significant decrease in
blade speed.
• Gently press down the handle to perform the cut. If the
handle is pressed down with force or if lateral force is
applied, the blade will vibrate and leave a mark (saw
mark) in the workpiece and the precision of the cut will
be impaired.
• During a slide cut, gently push the carriage toward the
guide fence without stopping. If the carriage movement
is stopped during the cut, a mark will be left in the work-
piece and the precision of the cut will be impaired.
1.
Press cutting (cutting small workpieces)
(Fig. 40)
Workpieces up to 68 mm high and 160 mm wide can be
cut in the following way.
After turning the stopper lever clockwise and sliding the
carriage to your desired position, push the carriage
toward the guide fence fully and tighten the locking screw
clockwise and pull the lock lever toward yourself to
secure the carriage. Secure the workpiece with the vise.
Switch on the tool without the blade making any contact
and wait until the blade attains full speed before lowering.
Then gently lower the handle to the fully lowered position
to cut the workpiece. When the cut is completed, switch
off the tool and WAIT UNTIL THE BLADE HAS COME
TO A COMPLETE STOP before returning the blade to its
fully elevated position.
CAUTION:
• Firmly tighten the locking screw clockwise and pull the
lock lever toward yourself so that the carriage will not
move during operation. Insufficient tightening may
cause unexpected kickback of the blade. Possible seri-
ous PERSONAL INJURY may result.
19

Advertisement

loading

This manual is also suitable for:

Ls1016l