Table of Contents
Advertisement
Quick Links
Order No. 4239
BUILDING INSTRUCTIONS
ELEKTRO-ROOKIE QR
RC electric-powered model for three LiPo cells of around 2500 mAh
This model requires a 3-function or 4-function HoTT radio control system
GRAUPNER GmbH & Co. KG D-73230 KIRCHHEIM/TECK GERMANY
Modifications reserved. No liability for printing errors. Id.-Nr. 0062273
3/2011
- 1 -
Advertisement
Table of Contents
Subscribe to Our Youtube Channel
Related Manuals for GRAUPNER ELEKTRO-ROOKIE QR
Summary of Contents for GRAUPNER ELEKTRO-ROOKIE QR
-
Page 1: Building Instructions
RC electric-powered model for three LiPo cells of around 2500 mAh This model requires a 3-function or 4-function HoTT radio control system GRAUPNER GmbH & Co. KG D-73230 KIRCHHEIM/TECK GERMANY Modifications reserved. No liability for printing errors. Id.-Nr. 0062273 3/2011... - Page 2 Introduction The ELEKTRO-ROOKIE QR is an RC model aircraft designed expressly for the newcomer to model flying, and offers a superb performance in the air. Either the rudder or the ailerons can be set up as the primary directional control. If you intend only to fit rudder control at first, it is nevertheless an easy job to fit working ailerons at a later stage.
-
Page 3: Fuselage Stiffening Tube
Unscrew the original output levers from the C231 servos, and set the servos to centre (neutral) from the transmitter. Mount parts (5) to (9) on the servo output arms (6) as GRAUPNER GmbH & Co. KG D-73230 KIRCHHEIM/TECK GERMANY Modifications reserved. No liability for printing errors. Id.-Nr. 0062273... -
Page 4: Swivel Pushrod Connector
- as shown in the photo - so that the BRUSHLESS CONTROL 18 speed controller lies flat on the fuselage. Tack the speed controller in place with a little adhesive. GRAUPNER GmbH & Co. KG D-73230 KIRCHHEIM/TECK GERMANY Modifications reserved. No liability for printing errors. Id.-Nr. 0062273 3/2011... -
Page 5: Threaded Insert
The first step in joining the shells is to offer them up “dry” (no glue). It is a good idea to secure the loose cables temporarily with tape to avoid them getting caught in the joint. GRAUPNER GmbH & Co. KG D-73230 KIRCHHEIM/TECK GERMANY Modifications reserved. No liability for printing errors. Id.-Nr. 0062273 3/2011... -
Page 6: Canopy Retainer Clip
Glue the spreader plate (21) to the top of the tailplane as shown, and glue the horn (15) in the slot in the underside of the elevator. GRAUPNER GmbH & Co. KG D-73230 KIRCHHEIM/TECK GERMANY Modifications reserved. No liability for printing errors. Id.-Nr. 0062273... -
Page 7: Centre
(31), two aileron horns (15), and two C 231 servos. Please refer to the section entitled “Control surface checks” for information on control surface travels. GRAUPNER GmbH & Co. KG D-73230 KIRCHHEIM/TECK GERMANY Modifications reserved. No liability for printing errors. Id.-Nr. 0062273 3/2011 - 7 -... -
Page 8: Centre
Check that the servos work properly before securing them with a drop of glue on each mounting lug. Installing the receiving system GRAUPNER GmbH & Co. KG D-73230 KIRCHHEIM/TECK GERMANY Modifications reserved. No liability for printing errors. Id.-Nr. 0062273 3/2011... -
Page 9: Control Surface Horn
(15). If you are a relative beginner to model flying, we recommend that you connect the pushrods to the outer holes. GRAUPNER GmbH & Co. KG D-73230 KIRCHHEIM/TECK GERMANY Modifications reserved. No liability for printing errors. Id.-Nr. 0062273 3/2011... - Page 10 It is not necessary to paint the model’s SOLIDPOR® components. If you wish to give the aircraft a coloured finish, we recommend the use of GRAUPNER LEXACOLOR spray paints, Order No. 945... Do not rub down the surfaces prior to painting; instead wipe them with cellulose thinners, Order No.
-
Page 11: Tailplane
Just before touch-down, apply slight up- elevator to flare out and slow the machine down further. All of us at GRAUPNER Modellbau wish you many fine flights with your new ELEKTRO-ROOKIE QR Specification Wingspan approx. -
Page 12: Table Of Contents
Dry cells and rechargeable batteries must be removed from the device and taken separately to a suitable battery disposal centre. GRAUPNER GmbH & Co. KG D-73230 KIRCHHEIM/TECK GERMANY Modifications reserved. No liability for printing errors. Id.-Nr. 0062273 3/2011... -
Page 13: Modifications Reserved. No Liability For Printing Errors. Id.-Nr
Refer to your RC system instructions for more details. It is important to use only those parts included in the kit, together with other genuine Graupner accessories and replacement parts as recommended expressly by us. Even if you change a single component, you can no longer be sure that the whole system will work reliably, and such changes also invalidate your guarantee. - Page 14 When switching off, reverse the order: receiving system first, then the transmitter. GRAUPNER GmbH & Co. KG D-73230 KIRCHHEIM/TECK GERMANY Modifications reserved. No liability for printing errors. Id.-Nr. 0062273...
- Page 15 If material defects or manufacturing faults should arise in a product distributed by us in the Federal Republic of Germany and purchased by a consumer (§ 13 BGB), we, Graupner GmbH & Co. KG, D-73230 Kirchheim/Teck, Germany, acknowledge the obligation to correct those defects within the limitations described below.
Need help?
Do you have a question about the ELEKTRO-ROOKIE QR and is the answer not in the manual?
Questions and answers