Using Jbl Connect; Using Audio Feedback; Using Own Tv Remote Control; Troubleshooting - JBL BOOST TV Owner's Manual

JBL BOOST TV
1. Confirm that you have paired at least one Bluetooth device to JBL Boost TV (See
"Using Bluetooth" section).
2. Press the TV button on the Remote Control or Top-panel buttons until the LED turns
BLUE. This color indicates that JBL SoundShift is ON.
3. Play sound from your TV through your JBL Boost TV in a normal manner.
4. Press PLAY on your mobile device to stream music. You will hear the Bluetooth audio
"break in" over your TV sound.
5. Press PAUSE on your mobile device. You will hear the audio automatically switch
back to your TV.

USING JBL CONNECT

JBL Connect lets you wirelessly daisy chain multiple speakers. JBL Connect requires
an additional compatible speaker like JBL Flip 3, JBL Xtreme, or JBL Pulse 2. For more
information, please visit our website at www.jbl.com
1. Confirm that you have paired at least one Bluetooth device to JBL Boost TV
2. Press the JBL Connect button on the remote control or the top-panel button on JBL
Boost TV.
3. Press the JBL Connect button on your other JBL speaker.
4. Stream music from your wireless device. You will hear sound on both speakers
5. The volume is synchronized between the two devices—turning the volume up or
down on one device will affect the other.
6. To disable JBL Connect, turn off the second device.
NOTE: JBL Connect supports Bluetooth audio streaming only. Audio from the wired
TV input will not stream to the second JBL device.

USING AUDIO FEEDBACK

Audio feedback enables audible tones indicate certain product features. When Audio
feedback is ON, you will hear tones for specific actions on the JBL Boost TV:
1. Bluetooth Pairing is ON.
2. Bluetooth device is connected
3. JBL Connect paring is ON
4. JBL Connect device is connected
5. JBL SoundShift On/Off

USING VIRTUAL SURROUND

Harman Display Surround brings rich virtual surround sound to your home entertainment
experience. Turn Harman Display Surround ON when you are watching movies for a wide,
spacious sound effect.
HARMAN International Industries,
Incorporated 8500 Balboa Boulevard,
Northridge, CA 91329 USA
www.jbl.com
4
1. To turn Harman Display Surround ON, press
the button on the remote control or the top-
panel.
2. The button light is off for Harman Display
Surround OFF, White for ON.
USING YOUR OWN TV REMOTE CONTROL (TV REMOTE
LEARNING)
1. Press button on device
2. Press button on remote
You can use your own TV remote control to command JBL Boost TV. For example, when
you press POWER ON, you will turn on your TV and JBL Boost TV at the same time. This
simplifies your system helps you keep your TV and speaker in sync.
1. Confirm that JBL Boost TV is ON
2. Press and hold the top-panel Harman Display Surround Button for 5 seconds until
the LED flashes amber. If the LED does not flash, release the button and try again.
3. Press the JBL Boost TV top-panel VOLUME UP button
4. Aim the TV remote at the front of the JBL boost TV and slowly press the VOLUME UP
button on the TV remote until the Harman Display Surround button flashes white for
one second. This indicates that the programming operation has been successful.
5. Repeat steps 3 and 4 for VOLUME DOWN, POWER, and MUTE (to mute the JBL Boost
TV, press VOLUME UP and VOLUME DOWN buttons at the same time).
6. To exit the learning mode (at any time or when the learning is complete), press and
hold the Harman Display Surround button until the amber LED stops flashing.

TROUBLESHOOTING

If your JBL Boost TV does not perform the way you think it should, check whether the
problem is covered in this section before contacting you dealer or a JBL representative.
Problems
If the speaker does not turn ON
If there is no sound coming from the
speaker
If there is NO sound from the system,
even when the speaker's volume is
turned all the way up
© 2015 HARMAN International Industries, Incorporated. All rights reserved. JBL is a trademark of
HARMAN International Industries, Incorporated, registered in the United States and/or other countries.
All Rights Reserved. Features, specifications and appearance are subject to change without notice.
Harman Display Surround ON.
Harman Display Surround OFF.
LED BEHAVIOR
Command is learned
Solutions
Check if the speaker power supply's AC
cord is plugged into a working AC outlet
and that the power supply is plugged
into the speaker.
Check the power is set to ON, then
check to see if the volume is turned up.
Check if your TV has certain settings to
enable the audio connection.
If the TV or source component is
connected via a variable output, check
its instructions if the output is not turned
down too low.
TV
SOURCE
TR01354_A