Welcome Thank You Limited Warranty BluePack is covered by a 2 year Thank you for purchasing the JK Audio BluePack. Please read this warranty to be free from defective guide for instructions on using it. workmanship and materials. To obtain...
Doing so may hinder your hearing and can be hazardous on the JK Audio products are designed for roadways or at pedestrian crossings. the broadcast industry. The broadcast professional must be able to hear headphone signals over the ambient noise level.
Getting Connected Bluetooth Wireless Technology 6 Bluetooth Status LED 7 Pairing 8 Hands-Free, Headset & Master Mode 9 Switching to Master Mode 10 Connection History, Reconnecting to a Device, Disconnecting from a Device FAQs Technical Information BluePack Wireless Interview Tool...
Page 5
Contents Features HD Voice* 3.5 Mm Stereo Line Input and Output Bluetooth Wireless Technology ¼" Stereo Headphone Jack XLR Mic Input >10 Hours on one 9 Volt Alkaline Battery * HD Voice. While standard phone calls have a narrow bandwidth of 300 Hz to 3.4 kHz, HD Voice calls offer 50 Hz to 7 kHz bandwidth.
Introducing BluePack JK Audio combines professional audio electronics with a flexible communications interface in a rugged new belt pack design. BluePack™ offers a professional look and feel to field reporters and live remote talent. BluePack™ allows you to perform live man-on-the-street interviews through your cell phone in HD Voice.
Use the establish a Bluetooth connection thumbwheel on the top of the to your wireless phone. Dial up the BluePack to set the volume level for studio and you are ready to go. the mic input. Add prerecorded sound clips or...
The microphone and Aux Send are a combined input. If you see this red LED flashing, you should decrease the Mic and/or Aux Send input levels. BluePack Wireless Interview Tool...
Page 9
Technology. 4) Stereo LED (Listen-Only) 6) Headphones Control This LED flashes Red when the Sets the level of audio sent to the BluePack has a stereo listen-only headphone output jack. (Slave) audio connection with your 7) Power Indicator Bluetooth device.
XLR mic bandwidth microphone signal on the input, 3.5 mm Aux Send input and the left channel and the Bluetooth audio Headset Interface audio. on the right channel. BluePack Wireless Interview Tool...
Page 11
Getting Connected 4) Mic Input This stereo output jack allows you to make a full bandwidth recording using Connect your dynamic microphone your favorite recorder for transfer back to the XLR jack. This device will at the station or over the web. not provide phantom power for a condenser type microphone.
To put the unit in within range can pair with your Idle Mode, press the blue MFB for BluePack. To put the unit in Pairing 4 seconds when the unit is on. The Mode, press the blue MFB for 6 blue LED will flash at a rate of 2 seconds off, 200ms on.
Page 13
1 sec on. (2 secs off, 4 secs 2. Press and hold the blue MFB button on for HD Voice) Once BluePack on the BluePack. Hold for 6 full has been added to your cell phone, seconds. After you release the MFB...
Page 14
A2DP audio to the Headset Distribution Profile): device. A2DP music streaming is a Used for stereo music streaming. one-way path from Master to Headset. BluePack can act as either a Master Headset: Facilitates mono, or Headset. Please note that wireless full-duplex audio between two phones typically cannot receive A2DP paired devices.
Page 15
Master mode. The ST LED will flash Red when it is in Headset mode. The ST LED only indicates whether the BluePack is in Master or Headset Mode on Startup and when the Master/Headset role is switched.
Page 16
Reconnecting to a Device with Bluetooth Wireless When reconnecting to a device that is Technology still in BluePack's pairing history, the device that will be in Headset mode To disconnect from the Bluetooth should be powered up first. Then device, simply press the MFB and...
Bluetooth device to while before the battery is completely conserve battery power. exhausted and the unit shuts down. Can I pair my BluePack to two cell phones and send my audio to two locations simultaneously? No, your BluePack can only connect to one Bluetooth enabled device at a time.
Page 18
This input would be a good place to will be connected to our device as add background music or sound clips if the BluePack were a headset. during a live interview that is being So you need to use a microphone...
Page 19
Mic and/or Aux Send input levels until the combined input is no longer clipping. My BluePack won’t pair with my cell phone. Why won’t it accept the PIN? If this is the first time you have paired...
1311 E 6 Street Sandwich, Illinois 60548 USA Declares that the product: Product Name BluePack™ Wireless Interview Tool Model Numbers BluePack Conforms to the following Product Specifications: ESD: EN 61000-3-2, 3-3, 4-3, 4-4, 4-5, 4-6, 4-11 EN 301 489-17 V1.2.1...
Page 23
FCC Part 15 Compliance Notice The Technical File containing supporting documentation is maintained at: JK Audio, Inc (Corporate Headquarters) Compliance Manager 1311 E 6th Street Sandwich, Illinois 60548 USA 815-786-2929 phone 815-786-8502 fax FCC Part 15 Compliance of this equipment in a residential area is...