Toro Riding Mower Safety - Toro 30344 Operator's Manual

•
Check the area to be mowed and never fold down a
folding ROPS in areas where there are slopes, drop offs
or water
•
Check carefully for overhead clearances (i.e. branches,
doorways, electrical wires) before driving under any
objects and do not contact them
•
Keep the ROPS in safe operating condition by
periodically thoroughly inspecting for damage and
keeping all mounting fasteners tight.
•
Replace a damaged ROPS. Do not repair or revise.
•
Do not remove the ROPS.
•
Any alterations to a ROPS must be approved by the
manufacturer.
Maintenance and Storage
•
Keep all nuts, bolts and screws tight to be sure the
equipment is in safe working condition.
•
Never store the equipment with fuel in the tank inside a
building where fumes may reach an open flame or spark.
•
Allow the engine to cool before storing in any enclosure.
•
To reduce the fire hazard, keep the engine,
silencer/muffler, battery compartment and fuel storage
area free of grass, leaves, or excessive grease.
•
Keep all parts in good working condition and all hardware
and hydraulic fittings tightened. Replace all worn or
damaged parts and decals.
•
If the fuel tank has to be drained, do this outdoors.
•
Be careful during adjustment of the machine to prevent
entrapment of the fingers between moving blades and
fixed parts of the machine.
•
On multi-spindle mowers, take care as rotating 1 blade
can cause other blades to rotate.
•
Disengage drives, lower the deck, set parking brake, stop
engine and remove the key from the ignition. Wait for all
movement to stop before adjusting, cleaning or repairing.
•
Clean grass and debris from decks, drives,
silencers/mufflers, engine and underside of machine to
help prevent fires. Clean up oil or fuel spillage.
•
Use jack stands to support components when required.
•
Carefully release pressure from components with stored
energy.
•
Disconnect battery before making any repairs. Disconnect
the negative terminal first and the positive last. Reconnect
positive first and negative last.
•
Use care when checking the blades. Wear gloves and use
caution when servicing them. Only replace blades. Never
straighten or weld them.
•
Keep hands and feet away from moving parts. If possible,
do not make adjustments with the engine running.
•
Charge batteries in an open well ventilated area, away
from spark and flames. Unplug charger before connecting
or disconnecting from battery. Wear protective clothing
and use insulated tools.
Hauling
•
Use care when loading or unloading the machine into a
trailer or truck.
•
Use full width ramps for loading machine into trailer or
truck.
•
Tie the machine down securely using straps, chains, cable,
or ropes. Both front and rear straps should be directed
down and outward from the machine.

Toro Riding Mower Safety

The following list contains safety information specific to Toro
products or other safety information that you must know that
is not included in the CEN, ISO, or ANSI standard.
This product is capable of amputating hands and feet and
throwing objects. Always follow all safety instructions to
avoid serious injury or death.
Use of this product for purposes other than its intended use
could prove dangerous to user and bystanders.
•
Know how to stop the engine quickly.
•
Do not operate the machine while wearing tennis shoes
or sneakers.
•
Wearing safety shoes and long pants is advisable and
required by some local ordinances and insurance
regulations.
•
Handle fuel carefully. Wipe up any spills.
•
Check the safety interlock switches daily for proper
operation. If a switch should fail, replace the switch
before operating the machine.
•
Before starting the engine, sit on the seat.
•
Using the machine demands attention. To prevent loss
of control:
– Do not drive close to sand traps, ditches, creeks, or
other hazards.
– Reduce speed when making sharp turns. Avoid
sudden stops and starts.
– This machine is not designed or equipped for on-road
use and is a "slow-moving vehicle." If you must cross
or travel on a public road, you should be aware of and
comply with local regulations, such as required lights,
slow moving vehicle signs, and reflectors.
– When near or crossing roads, always yield the
right-of-way.
– Apply the service brakes when going downhill to
keep forward speed slow and to maintain control of
the machine.
•
Raise the deck when driving from a work area to another.
•
Do not touch the engine, silencer/muffler, or exhaust
pipe while the engine is running or soon after it has
stopped because these areas could be hot enough to cause
burns.
6