Starting Warm Engine; Stopping Engine - Shindaiwa EB633RT Owner's/Operator's Manual

thirty (30) days, ninety (90) days when a fuel stabilizer is added.

sTarTInG Warm enGIne

1. Throttle Lever/Stop Switch
Move throttle lever (A) forward to idle position. Slide stop switch (B)
forward to run position.
sTarTInG Cold enGIne
2. Recoil Starter
sTarTInG Warm enGIne sTarTInG Warm enGIne
Recoil starter: Use short pulls - only 1/2-2/3 of rope length for starting.
Pull recoil starter handle (E) and engine should start. Do not use choke (C).
1. 1. Throttle Lever/Stop Switch Throttle Lever/Stop Switch
Do not allow the rope to snap back in. Always hold the unit firmly.
Move throttle lever (A) forward to idle position. Slide stop switch (B) Move throttle lever (A) forward to idle position. Slide stop switch (B)
1. Throttle Lever/Stop Switch
forward to run position. forward to run position.
NOTE
Move throttle lever (A) forward to idle position. Slide stop switch (B)
If engine does not start after 5 pulls, use cold start procedures.
forward to run position.
2. 2. Recoil Starter Recoil Starter
Pull recoil starter handle (E) and engine should start. Do not use choke (C). Pull recoil starter handle (E) and engine should start. Do not use choke (C).
2. Choke
Move choke (C) up to "Cold Start" position (
NOTE NOTE
3. Purge Bulb
If engine does not start after 5 pulls, use cold start procedures. If engine does not start after 5 pulls, use cold start procedures.
Pump purge bulb (D) until fuel is visible and flows freely in the clear
fuel tank return line. Pump bulb an additional 4 or 5 times.
4. Recoil Starter
Pull recoil starter handle (E) until engine fires (5 or 6 pulls maximum).
5. Choke
Move choke (C) down to run position (
engine.
NOTE
If engine does not start after 5 pulls, move choke to "Cold Start"

sToppInG enGIne

position, and repeat steps 4 & 5.
1. Throttle Trigger/Throttle Position Lever
NOTE
Release throttle trigger (C). Move throttle position lever (A) forward to
Allow engine to warm up before use.
idle position and allow engine to return to idle before shutting engine off.
2. Stop Switch
sToppInG enGIne sToppInG enGIne
Slide stop switch (B) to Stop position.
1. 1. Throttle Trigger/Throttle Position Lever Throttle Trigger/Throttle Position Lever
Release throttle trigger (C). Move throttle position lever (A) forward to Release throttle trigger (C). Move throttle position lever (A) forward to
WarnInG
idle position and allow engine to return to idle before shutting engine off. idle position and allow engine to return to idle before shutting engine off.
If engine does not stop when stop switch is moved to STOP position,
2. 2. Stop Switch Stop Switch
close choke - COLD START position - to stall engine. Have your
Slide stop switch (B) to Stop position. Slide stop switch (B) to Stop position.
Shindaiwa dealer repair stop switch before using blower again.
WarnInG WarnInG
If engine does not stop when stop switch is moved to STOP position, If engine does not stop when stop switch is moved to STOP position,
close choke - COLD START position - to stall engine. Have your close choke - COLD START position - to stall engine. Have your
Shindaiwa dealer repair stop switch before using blower again. Shindaiwa dealer repair stop switch before using blower again.
12
).
), and if necessary, restart
2 5.2 8
5 13 20
b
a
b
b b
a
a a
C
e
C C C
e e
E
d
C
b
a
e
C
b b
a a
C C
160
400
11
14