Onkyo TX-RZ1100 Basic Manual page 49

> Specifications > Settings
Setting Item Default Value
Double Bass On
■ 3� Distance
Set the distance from each speaker to the listening position.
Setting Item Default Value
Front Left 12' 0" / 3.60 m
Center 12' 0" / 3.60 m
Front Right 12' 0" / 3.60 m
Height 1 Left 9' 0" / 2.70 m
Height 1 Right 9' 0" / 2.70 m
Height 2 Left 9' 0" / 2.70 m
> Listening Modes > Playback Function
Setting Details
This can be selected only when "Configuration" -
"Subwoofer" is set to other than "No" and "Front" is
set to "Full Band".
Boost bass output by feeding bass sounds from
the front left and right, and center speakers to the
subwoofer.
"On": Bass output will be boosted
"Off": Bass output will not be boosted
• The setting will not automatically be configured
even if you performed AccuEQ Room
Calibration.
Setting Details
Specify the distance between each speaker and
the listening position.
Specify the distance between each speaker and
the listening position.
Specify the distance between each speaker and
the listening position.
Specify the distance between each speaker and
the listening position.
• Depending on the use of the ZONE speakers, it
may not be possible to select this setting.
Specify the distance between each speaker and
the listening position.
• Depending on the use of the ZONE speakers, it
may not be possible to select this setting.
Specify the distance between each speaker and
the listening position.
• Depending on the use of the ZONE speakers, it
may not be possible to select this setting.
Setting Item Default Value
Height 2 Right 9' 0" / 2.70 m
Surround Right 7' 0" / 2.10 m
Surr Back Right 7' 0" / 2.10 m
Surr Back Left 7' 0" / 2.10 m
Surround Left 7' 0" / 2.10 m
Subwoofer 1 12' 0" / 3.60 m
Subwoofer 2 12' 0" / 3.60 m
• Default values vary depending on the regions.
• Distance units can be switched by pressing MODE on the remote controller. When the unit is set as
feet, you can set between 0' 0" 1/2 and 30' 0" in increments of 1/2. When the unit is set as meters,
you can set between 0.01 m and 9.00 m in increments of 0.01 m.
■ 4� Level Calibration
Setting Item Default Value
Front Left 0.0 dB
Center 0.0 dB
> Basic Manual
Troubleshooting Appendix Troubleshooting | Appendix
Setting Details
Specify the distance between each speaker and
the listening position.
• Depending on the use of the ZONE speakers, it
may not be possible to select this setting.
Specify the distance between each speaker and
the listening position.
Specify the distance between each speaker and
the listening position.
• Depending on the use of the ZONE speakers, it
may not be possible to select this setting.
Specify the distance between each speaker and
the listening position.
• Depending on the use of the ZONE speakers, it
may not be possible to select this setting.
Specify the distance between each speaker and
the listening position.
Specify the distance between each speaker and
the listening position.
Specify the distance between each speaker and
the listening position.
Setting Details
Select a value between "－12.0 dB" and "＋12.0
dB" (in 0.5 dB increments). A test tone will be
output each time you change the value. Select the
desired level.
Select a value between "－12.0 dB" and "＋12.0
dB" (in 0.5 dB increments). A test tone will be
output each time you change the value. Select the
desired level.
|
13