Getting To Know Your Cleaner; Using Your Cleaner; Assembling Your Cleaner - Hoover XP81OP25 User Manual

GETTInG TO KnOw yOUR CLEAnER

A. Cleaner main body
B. Carry handle
C. Dust Container
D. Dust Container handle and latch
E. On/Off Button
F. Cord Rewind Button
G. Filter Door
H. Filter Door latch
I. Pre-Motor Filter Pack
J. Exhaust Filter Grid
K. Exhaust Filter
L. Parking slot
M. Handle
n. suction Control
O. Telescopic Tube
P. Telescopic Tube Adjuster
Q. Carpet and Floor nozzle(GP)**
Q1. Carpet nozzle (CA)**
Q2. Hard Floor nozzle (HF)**
R. surface selector**
s. Hose
T1. Crevice Tool
T2. Dusting Brush
U. Pet Hair Remover Mini Turbo nozzle*
V.. Allergen Remover Mini Turbo nozzle*
w. Grand Turbo nozzle*
X. Parquet nozzle*

AssEMBLInG yOUR CLEAnER

Remove all components from the packaging.
Connect the hose to the cleaner main body. [2]
1.
2. Connect the tube upper end to the navigator handle [3].
3. Connect the tube lower end to the carpet and floor nozzle. [4]
*Certain Models Only ** Certain models only, nozzles may vary according to model

UsInG yOUR CLEAnER

1. Extract power cord and plug it into the power supply. Do not pull the cord beyond the
red marker. [5]
2. Adjust the telescopic tube to the desired height by holding the handle and moving the
central hand grip up or down. [6]
3. select the type of surface to be cleaned by pressing the pedal in the nozzle. [7]
Hard Floor – Brushes are lowered to protect the floor.
Carpet – Brushes are raised for the deepest clean.
4. switch the cleaner on by pressing the On/Off Button on the cleaner main body. [8]
5. Adjust the suction by sliding the suction regulator to the desired level. [9]
6. switch off at the end of use by pressing the On/Off Button. Unplug and press the cord
rewind button to wind the power cord back into the cleaner. [10]
7. To store your cleaner adjust telescopic tube to the lowest height setting and park the
nozzle in the park position on the cleaner main body. [11]
ACCEssORIEs
To obtain the best performance and energy efficiency
nozzles are used for the main cleaning operations. These nozzles are indicated in the diagrams
by the letters GP, HF or CA.
A nozzle type GP can be used to clean both carpet and hard floor.
A nozzle type HF is suitable for use only on hard floor.
A nozzle of type CA is suitable for use only on carpet.
The other nozzles are accessories for specialist cleaning tasks and are recommended for oc-
casional use only.
It is important to note that this vacuum cleaner is supplied with an Energy Label as required by
European Regulation (EU) 665/2013.
If the label shows a red prohibition circle on the left covering the carpet symbol, then this indi-
cates that the vacuum cleaner is not suitable use on carpets.
If the label shows a red prohibition circle on the right covering the hard floor symbol, then this
indicates that the vacuum cleaneris not suitable for use on hard floors.
#1
NOTE: Dust pick up ability carpet, dust pick up ability hard floor, and energy efficiency in
accord with Commission Regulations (EU) 665/2013 and (EU) 666/2013.
Please see the model specification on the packaging label for inclusion of accessories to
individual models. All accessories can be purchased separately from Hoover. (see Hoover
spares and Consumable section).
All accessories can be fitted to the end of the hose or the end of the telescopic tube.
Crevice Tool – For corners and hard to reach areas. [12]
2
GB
#1
it is recommended that the correct