Download Print this page

Onkyo HT-R980 Instruction Manual page 40

Onkyo av receiver instruction manual

Advertisement

Available languages

Available languages

Speaker Distance
This setting is set automatically by Audyssey 2EQ
Room Correction and Speaker Setup function
Here you can specify the distance from each speaker to the
listening position so that the sound from each speaker
arrives at the listener's ears as the sound designer
intended.
Unit
feet:
Distances can be set in feet. Range: 1ft to 30ft in
1 foot steps.
meters:
Distances can be set in meters. Range: 0.3m to 9.0m
in 0.3 meter steps.
(The default setting varies from country to country.)
Left, Front High Left, Center, Front High Right,
Right, Surr Right, Surr Back Right, Surr Back
Left, Surr Left, Subwoofer
Specify the distance from the each speaker to your lis-
tening position.
Note
• Speakers that you set to "No" in the "Speaker Configuration"
cannot be selected
(➔
Level Calibration
This setting is set automatically by Audyssey 2EQ
Room Correction and Speaker Setup function
Adjust the level control of the subwoofer to the "THX"
position before calibrating this system.
Here you can adjust the level of each speaker with the
built-in test tone so that the volume of each speaker is the
same at the listening position.
Left, Front High Left, Center
Right, Surr Right, Surr Back Right, Surr Back
Left, Surr Left
–12dB to 0dB to +12dB in 1 dB step.
*1
Subwoofer
–15dB to 0dB to +12dB in 1 dB step.
Note
• Speakers that you set to "No" in the "Speaker Configuration"
cannot be selected
(➔
• Speakers that you set to "No" in the "Speaker Configuration" do
not output the test tone
• The speakers cannot be calibrated while the AV receiver is
muted.
• The test tone is output at the standard level for THX, which is
0 dB (absolute volume setting 82). If you normally listen at vol-
ume settings below this, be careful because the test tone will be
much louder.
*1
For the center speaker and subwoofer, the level settings made
by using the Audio menu are saved
En
40
(➔
39).
(➔
*1
, Front High Right,
39).
(➔
39).
(➔
22).
Tip
• If you're using a handheld sound level meter, adjust the level of
each speaker so that it reads 75 dB SPL at the listening position,
®
measured with C-weighting and slow reading.
23).
Equalizer Settings
This setting is set automatically by Audyssey 2EQ
Room Correction and Speaker Setup function
With the Equalizer settings, you can adjust the tone of
speakers individually with a 5-band equalizer. The volume
of each speaker can be set
Equalizer
Manual:
You can adjust the equalizer for each speaker manu-
ally. If you selected "Manual", continue with this
procedure.
1
Press w to select "Channel", and then use e/
r to select a speaker.
2
Use q/w to select a frequency, and then use
the e/r to adjust the level at that frequency.
The volume at each frequency can be adjusted
from –6dB to 0dB to +6dB in 1 dB steps.
Tip
• Low frequencies (e.g., 63Hz) affect bass sounds;
high frequencies (e.g., 16000Hz) affect treble
sounds.
3
Use q to select "Channel", and then use e/r
23).
to select another speaker.
Repeat steps 1 and 2 for each speaker.
You cannot select speakers that you set to "No"
in the "Speaker Configuration"
Audyssey:
This is selected automatically by Audyssey 2EQ
Room Correction and Speaker Setup function. The
Audyssey Dynamic Volume indicator will light
(➔
8) and "Dynamic EQ" and "Dynamic Volume"
become available
Off:
No Audyssey 2EQ equalizing will apply.
Note
• The front, center, surround, and surround back speakers can be
adjusted at 63Hz, 250Hz, 1000Hz, 4000Hz, and 16000Hz. The
subwoofer can be adjusted at 25Hz, 40Hz, 63Hz, 100Hz, and
160Hz.
• While the Direct listening mode is selected, the equalizer set-
tings have no effect.
• Audyssey equalizing does not work for DSD sources.
(➔
(➔
40).
(➔
39).
(➔
43).
23).

Hide quick links:

Advertisement

loading

This manual is also suitable for:

Ht-s9300thx