Toro 74310 Setup Instructions
  1. Manuals
  2. Brands
  3. Toro Manuals
  4. Lawn Mower
  5. Z MASTER 74310
  6. Setup instructions
Toro 74310 Setup Instructions

Toro 74310 Setup Instructions

With 42in or 48in direct-collect cutting unit
Hide thumbs Also See for 74310:
Table of Contents

Advertisement

Quick Links

Download this manual See also: Operator's Manual
Z Master
with 42in or 48in Direct-Collect Cutting Unit
Model No. 74310—Serial No. 314000001 and Up
Model No. 74311—Serial No. 314000001 and Up
Model No. 74312—Serial No. 314000001 and Up
WARNING
CALIFORNIA
Proposition 65 Warning
This product contains a chemical or chemicals
known to the State of California to cause cancer,
birth defects, or reproductive harm.
The engine exhaust from this product
contains chemicals known to the State of
California to cause cancer, birth defects,
or other reproductive harm.
Setup

Loose Parts

Use the chart below to verify that all parts have been shipped.
Procedure
1
2
3
4
5
6
7
8
9
© 2014—The Toro® Company
8111 Lyndale Avenue South
Bloomington, MN 55420
®
8000 Series Riding Mower
Description
No parts required
Rear caster wheel
Bolt (1/2 x 13 inches)
Locknut (1/2 inch)
No parts required
No parts required
No parts required
Wing nut (1/4 inch)
No parts required
No parts required
Number 2 general-purpose lithium-base
or molybdenum-base grease. (Purchase
separately.)
Register at www.Toro.com.
Form No. 3383-798 Rev B
Qty.
–
Open the crate.
1
1
Remove the machine from the crate.
1
–
Check the tire pressure.
–
Check the engine-oil level.
–
Check the wheel lug nut torque.
2
Install the battery.
–
Charge the battery.
–
Check the hydraulic oil.
1 tube
Check the machine for grease.
Original Instructions (EN)
All Rights Reserved *3383-798* B
Printed in the USA.
Setup Instructions
Use

Advertisement

Table of Contents
loading

Related Manuals for Toro 74310

Summary of Contents for Toro 74310

  • Page 1: Loose Parts

    Form No. 3383-798 Rev B Z Master ® 8000 Series Riding Mower with 42in or 48in Direct-Collect Cutting Unit Model No. 74310—Serial No. 314000001 and Up Model No. 74311—Serial No. 314000001 and Up Model No. 74312—Serial No. 314000001 and Up Setup Instructions WARNING...

  • Page 2: Opening The Crate

    Procedure Description Qty. Check the machine before delivery to – No parts required the customer (All machines). Operator's Manual Engine Owner's Manual Delivering the machine to the customer Registration card (All machines). Operator-training material 2. Remove the bolt holding the rear-frame support to the frame (Figure 1).
  • Page 3 provide support for the deck when the unit is driven off of the crate (Figure 4). Figure 2 1. Bolt (1/2 x 13 inches) 3. Locknut (1/2 inch) 2. Rear caster wheel g026150 Figure 4 7. Carefully remove the jack stands and lower the machine. 1.
  • Page 4 Figure 6 3. Push the deck locking pin 1. Deck lift handle g026151 in and rotate toward the Figure 8 front to lock 2. Rotate the deck locking 1. Front caster 3. Plywood between drive pin toward the rear and wheels pull outward to unlock 2.
  • Page 5 2. Remove the bolt holding the rear frame to the crate (Figure 11). 3. Lift the front of the hopper up. Note: Use care when hoisting the machine to prevent damage to the hopper. 4. Using the hoist, lift the machine at the location shown in Figure 9.
  • Page 6 Figure 13 Figure 12 1. Deck support pin 3. Side-strut hardware 2. Strut between the 1. Lift points on each side of the seat deck-support pins Important: Ensure the mower deck is in the 21. With the deck locking pins pulled out in the unlock upright position before raising the front of the position, carefully lower the deck (Figure 14).

  • Page 7: Installing The Battery

    WARNING Operating mower without locking pins securely latched can result in the mower deck folding up unexpectedly. The mower deck Installing the Battery folding up unexpectedly can cause serious injury. Parts needed for this procedure: Always operate mower with locking pins Wing nut (1/4 inch) securely latched.

  • Page 8: Charging The Battery

    The machine is shipped with hydraulic oil in the reservoir. No Parts Required 1. Check and ensure the reservoir has hydraulic oil. 2. If needed add Toro HYPR-OIL™ 500 hydraulic oil. Procedure 3. Run the machine for approximately 15 minutes to allow any extra air to purge out of the hydraulic system.
  • Page 9 Checking the Machine for Grease Parts needed for this procedure: Number 2 general-purpose lithium-base or 1 tube molybdenum-base grease. (Purchase separately.) Procedure Before you use the machine, check the machine for grease; refer to Lubrication in the Operator's Manual.
  • Page 10 Checking the Machine Before Delivery to the Customer No Parts Required Procedure Before delivering the machine to the customer, ensure that you perform or have performed the procedures listed in the following table and initial each when finished. Refer to the Operator's Manual for instructions on performing these procedures. Initial Check Procedure Check the tire pressure.
  • Page 11 Delivering the Machine to the Customer Parts needed for this procedure: Operator's Manual Engine Owner's Manual Registration card Operator-training material Procedure At delivery, fill in the model and serial number, complete the items listed in the following table, and initial each when finished. Model No.
  • Page 12 Make sure that the customer receives the Operator's Manual, Engine Owner's Manual, Set Up Instructions, and operator training material. Make sure the customer knows the Parts Catalog is available at www.Toro.com. Assist the customer in loading the machine. Note: When you, the dealer representative, have finished delivering the machine to the customer, sign and date in the space provide below and keep a copy of this page for dealer records.

This manual is also suitable for:

7431174312Z master 8000 series

Table of Contents