Advertisement

Owner's Manual
Jigsaw
054-8201-6
CAUTION:
Before using this
jigsaw or any of its
accessories, read this
manual and follow all
Safety Rules and
Operating Instructions.
Imported by Trileaf Distribution Trifeuil Toronto, Canada M4S 2B8
Rev 1.3
30/01/2010
General Safety Rules
Specific Safety Rules
and Symbols
Functional Description
Assembly
Operation
Maintenance
Accessories

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the 054-8201-6 and is the answer not in the manual?

Questions and answers

Subscribe to Our Youtube Channel

Summary of Contents for jobmate 054-8201-6

  • Page 1 Owner’s Manual Jigsaw 054-8201-6  General Safety Rules CAUTION:  Specific Safety Rules Before using this and Symbols jigsaw or any of its  Functional Description accessories, read this  Assembly manual and follow all  Operation Safety Rules and ...
  • Page 2: Table Of Contents

    This product is not guaranteed against wear or breakage due to misuse and/or abuse. This product is not guaranteed if used for industrial or commercial purposes. TOLL FREE HELPLINE: 1-866-JOBMATE SPECIFICATIONS Rating: 120 V, 60 Hz, AC Amperes: 3.5 A...
  • Page 3: Power Tool Safety

    POWER TOOL SAFETY WARNING: To avoid electrical hazards, fire hazards or damage to the jigsaw, use proper circuit protection. The jigsaw is wired at the factory for 120 V operation. It must be connected to a 120 V, 15 A time delayed fuse or circuit breaker. To avoid shock or fire, replace power cord immediately if it is worn, cut or damaged in any way.
  • Page 4 POWER TOOL SAFETY Don’t expose power tools to rain or wet GENERAL SAFETY RULES conditions. Water entering the power tool will increase the risk of electric shock. WARNING: Read and understand all instructions. Failure to follow all Do not abuse the cord. Never use the instructions listed below may result in cord to carry the tools or pull the plug from electric shock, fire and/or serious personal...
  • Page 5: Specific Safety Rules

    POWER TOOL SAFETY Do not overreach. Keep proper footing Check for misalignment or binding of and balance at all times. Proper footing moving parts, breakage of parts and any other condition that may affect the tool’s and balance enables better control of the operation.
  • Page 6: Extension Cord Guidelines

    SPECIFIC SAFETY RULES EXTENSION CORD GUIDELINES WARNING: Non-compliant eyewear can cause serious injury if Make sure your extension cord is the broken during operation of a power tool. proper size. When using an extension cord, be sure to use one heavy enough to WARNING: Always use a dust carry the current the tool will draw.
  • Page 7: Symbols

    EXTENSION CORD SYMBOLS GUIDELINES pascals MINIMUM GAUGE (AWG) EXTENSION CORDS (120 V use only) minutes Amperage rating Total length seconds More more 100' 150' alternating current than than (7.5 m) (15 m) (30 m) (45 m) three-phase alternating current three-phase alternating Not Applicable current with neutral direct current...
  • Page 8: Know Your Jigsaw

    KNOW YOUR JIGSAW Lock-on Trigger button switch Hex key holder 3 mm Hex key Motor vents Vacuum adaptor Chip guard Tilting sole plate Blade roller Blade...
  • Page 9: Accessories

    ACCESSORIES & CARTON CONTENTS AVAILABLE ACCESSORIES WARNING: Use only accessories recommended for this jigsaw. Follow instructions that accompany accessories. Use of improper accessories may cause injury to the operator or damage to the jigsaw. Do not use any accessory unless you have completely read the instructions or Owner’s Manual for that accessory.
  • Page 10: Assembly & Operation

    ASSEMBLY & OPERATION INSTALLING BLADES WARNING: Always disconnect your jigsaw from the power source when Unplug your jigsaw from the power replacing blades, tilting saw base, source. cleaning or when not in use. Disconnecting the saw will prevent WARNING: Failure to unplug accidental starting that could cause serious personal injury.
  • Page 11 ASSEMBLY & OPERATION ON/OFF TRIGGER SWITCH WARNING To turn your jigsaw ON, depress the trigger Have you read “POWER TOOL switch (1) (see Fig. 3). Release the trigger SAFETY”, “SPECIFIC SAFETY switch to turn the jigsaw OFF. RULES”, “EXTENSION CORD GUIDELINES”...
  • Page 12 ASSEMBLY & OPERATION BEVEL CUTTING - cont’d GENERAL CUTTING WARNING : Keep hands and Loosen both base pivot screws (1) until fingers away from between the motor the base (2) can be rotated (see housing and blade clamp. Do not reach Fig.
  • Page 13 ASSEMBLY & OPERATION PLUNGE CUTTING – cont’d PLUNGE CUTTING WARNING: Start the saw and slowly lower the To avoid loss of blade onto the workpiece while making control, broken blades or damage to the sure the front of the saw base remains workpiece, always use extreme caution in contact with the workpiece.
  • Page 14: Maintenance

    MAINTENANCE GENERAL WARNING: When servicing, use only identical JobMate parts. Use of any other part may create a hazard or cause product damage. WARNING: Do not at any time allow solvents such as brake fluids, gasoline, petroleum-based products, penetrating oils, etc. to come in contact with plastic parts.
  • Page 15: Parts & Service

    PARTS DIAGRAM – MODEL 054-8201-6 Jigsaw...
  • Page 16 PARTS LIST – MODEL 054-8201-6 Jigsaw When servicing, use only JobMate™ replacement parts. Use of any WARNING: other parts may create a HAZARD or cause damage to your power tool. Any attempt to repair or replace electrical parts on this power tool may create a hazard unless repair is performed by a qualified technician.
  • Page 17 PARTS LIST – MODEL 054-8201-6 Key # Part # Part Name Quantity 224380 Reciprocating lever 236500 Blade clamp 501506 Hex screw M4x12 300099 Housing (left) 312159 Guard 145012 Base plate 143615 Blade support 224491 Fixing plate 501507 Hex screw M4x14...

Table of Contents

Save PDF