Download Print this page

JVC KD-NX901 Service Manual

Hdd navigation / dvd receiver.
Hide thumbs

Advertisement

2005
MA161
6
1
PRECAUTIONS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-4
2
SPECIFIC SERVICE INSTRUCTIONS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-7
3
DISASSEMBLY . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-8
4
ADJUSTMENT . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-26
5
TROUBLESHOOTING . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-33
Downloaded from
www.Manualslib.com
SERVICE MANUAL
HDD NAVIGATION / DVD RECEIVER
KD-NX901
Lead free solder used in the board (material : Sn-Ag-Cu, melting point : 219 Centigrade)
COPYRIGHT ┬ę 2005 Victor Company of Japan, Limited
manuals search engine
TABLE OF CONTENTS
Area suffix
E ------------- Southern Europe
No.MA161
2005/6

Advertisement

   Also See for JVC KD-NX901

   Related Manuals for JVC KD-NX901

   Summary of Contents for JVC KD-NX901

  • Page 1: Table Of Contents

    SERVICE MANUAL HDD NAVIGATION / DVD RECEIVER MA161 2005 KD-NX901 Area suffix E ------------- Southern Europe Lead free solder used in the board (material : Sn-Ag-Cu, melting point : 219 Centigrade) TABLE OF CONTENTS PRECAUTIONS ............... 1-4 SPECIFIC SERVICE INSTRUCTIONS .

  • Page 2

    SPECIFICATION NAVIGATION SYSTEM System & Service L1, C/A code Global Positioning System Standard Positioning Service Reception System 15-channel multi-channel reception system Reception Frequency 1 575.42 MHz Sensitivity -130 dBm Update Rate 1/second, continuous GPS Antenna Polarization Right Handed Circular Polarization 30.4 mm ×...

  • Page 3

    DVD/CD PLAYER SECTION Signal Detection System Non-contact optical pickup (semiconductor laser) Number of Channels 2 channels (stereo) Frequency Response DVD, fs=48 kHz/96 kHz 16 Hz to 20 000 Hz VCD/CD 16 Hz to 20 000 Hz Dynamic Range 96 dB Signal-to-Noise Ratio 98 dB Wow and Flutter...

  • Page 4: Precautions

    SECTION 1 PRECAUTIONS Safety Precautions Burrs formed during molding may be left over on some parts of the chassis. Therefore, pay attention to such burrs in the case of preforming repair of this system. Please use enough caution not to see the beam directly or touch it in case of an adjustment or operation check.

  • Page 5

    Preventing static electricity Electrostatic discharge (ESD), which occurs when static electricity stored in the body, fabric, etc. is discharged, can destroy the laser diode in the traverse unit (optical pickup). Take care to prevent this when performing repairs. 1.2.1 Grounding to prevent damage by static electricity Static electricity in the work area can destroy the optical pickup (laser diode) in devices such as CD players.

  • Page 6

    Important for laser products 5.CAUTION : If safety switches malfunction, the laser is able 1.CLASS 1 LASER PRODUCT to function. 2.DANGER : Invisible laser radiation when open and inter 6.CAUTION : Use of controls, adjustments or performance of lock failed or defeated. Avoid direct exposure to beam. procedures other than those specified here in may result in 3.CAUTION : There are no serviceable parts inside the hazardous radiation exposure.

  • Page 7: Specific Service Instructions

    SECTION 2 SPECIFIC SERVICE INSTRUCTIONS This service manual does not describe SPECIFIC SERVICE INSTRUCTIONS. (No.MA161)1-7 Downloaded from www.Manualslib.com manuals search engine...

  • Page 8: Disassembly

    SECTION 3 DISASSEMBLY Main body section 3.1.1 Removing the front panel assembly (See Fig1) (1) Push the detach button in the lower right part of the front panel assembly. Front panel assembly (2) Remove the front panel assembly. Detach button Fig.1 3.1.2 Removing the heat sink (See Fig.2)

  • Page 9

    3.1.3 Removing the top chassis assembly (See Figs.3 to 6) • Prior to performing the following procedure, remove the front panel assembly, heat sink. Bottom chassis assembly Reference: CN601 Remove the front panel assembly as required. (1) From the bottom side of the main body, remove the two screws C and screw D attaching the top chassis assembly to the bottom chassis assembly.

  • Page 10

    3.1.4 Removing the front chassis assembly (See Figs.7 to 9) • Prior to performing the following procedure, remove the front panel assembly, heat sink and top chassis assembly. Top chassis assembly (1) From the both sides of the top chassis assembly, remove the two screws F attaching the front chassis assembly.

  • Page 11

    3.1.5 Removing the CPU board (See Figs.10 and 11) • Prior to performing the following procedure, remove the front panel assembly, heat sink and top chassis assembly. (1) From the inside of the top chassis assembly, remove the four screws H attaching the CPU case (bottom). (See Fig.10) (2) Release the lock of the connector CN561...

  • Page 12

    3.1.6 Removing the HDD (See Fig.12) • Prior to performing the following procedure, remove the front panel assembly, heat sink and top chassis assembly. (1) From the inside of the top chassis assembly, remove the four screws J attaching the HDD. (2) Release the lock of the connector CN562 on the HDD, dis-...

  • Page 13

    3.1.8 Removing the main board (See Figs.14 and 15) • Prior to performing the following procedure, remove the front panel assembly, heat sink and top chassis assembly. Rear bracket (1) From the rear side of the bottom chassis assembly, remove the screws M and N attaching the rear bracket to the bot- tom chassis assembly.

  • Page 14

    3.1.9 Removing the rear bracket (See Figs.16 and 17) • Prior to performing the following procedure, remove the front panel assembly, heat sink, top chassis assembly and main Main board board. (1) Remove the two screws Q attaching the wire holder to the rear bracket.

  • Page 15

    3.1.10 Removing the gear bracket unit (See Fig.18) • Prior to performing the following procedure, remove the front panel assembly, heat sink, top chassis assembly and main Bottom chassis Gear bracket unit board. (1) From the top side of the bottom chassis assembly, remove the screw V attaching the FPC guide.

  • Page 16

    3.1.11 Removing the switch board (See Figs.19 to 21) • Prior to performing the following procedure, remove the front panel assembly. Rear cover assembly (1) From the rear side of the front panel assembly, remove the five screws X attaching the rear cover assembly to the front panel assembly.

  • Page 17

    DVD mechanism assembly 3.2.1 Removing the chassis assembly (See Fig.1) (1) Remove the screw A attaching the lug wire. (2) Remove the six screws B attaching the chassis assembly. Chassis assembly (3) Remove the chassis assembly. Fig.1 3.2.2 Removing the mechanism control board (See Fig.2) Caution: Before disconnecting the flexible wire extending from the DVD...

  • Page 18

    3.2.3 Removing the top cover (See Fig.3) (1) Remove the two screws E attaching the top cover on the back of the body. (2) Remove the top cover upward. Reference: When reassembling, set part b of the top cover under the bending part c of the chassis frame.

  • Page 19

    3.2.5 Removing the clamper unit (See Figs. 6 to 10) • Remove the top cover and the mechanism section. (1) Remove the clamper2 spring on the bottom of the mecha- Clamper unit nism section. (See Figs.6.and 10) (2) Release the part d of the clamper spring from the bending part of the chassis base assembly.

  • Page 20

    Clamper unit Clamper spring Chassis base assembly Fig.8 Notch Clamper unit Fig.10 Clamper spring Fig.9 1-20 (No.MA161) Downloaded from www.Manualslib.com manuals search engine...

  • Page 21

    3.2.7 Removing the front unit (See Figs.11 to 13) • Remove the top cover and the mechanism section. (1) Disconnect the flexible wire from connector CN202 on the mechanism control board at the bottom of the body. (See Front unit Fig.11) (2) Remove the screw G attaching the front unit on the top of the body.

  • Page 22

    3.2.8 Removing the loading arm assembly (See Figs.14 and 15) • Remove the top cover, the mechanism section and the front unit. (1) From the top of the body, move the loading arm assembly from the front side upward, and release the bosses from the right and left joints m and n of the chassis base assem- bly.

  • Page 23

    3.2.9 Removing the rod (L)(R) and roller assembly (See Figs.16 and 17) • Remove the top cover, the mechanism section, the front unit and the loading arm assembly. Collar Collar (1) Release the rod (L) and (R) from the joints r at the bottom of the loading arm assembly (See Fig.16) (2) Remove the roller assembly from the loading arm assem- bly.

  • Page 24

    3.2.10 Removing the DVD pickup assembly (See Figs.18 to 20) • Remove the mechanism control board. (1) From the bottom of the body, turn the feed gear in the di- Feed gear rection of the arrow to move the DVD pickup outwards. (See Fig.18) (2) Remove the screw J attaching the thrust spring.

  • Page 25

    3.2.11 Removing the spindle motor (See Fig.21) • Remove the mechanism control board. Remove the two screws M attaching the spindle motor on the Spindle motor bottom of the body. Caution: Perform adjustment when reattaching the spindle motor. Fig.21 3.2.12 Removing the feed motor assembly (See Figs.22 and 23) •...

  • Page 26: Adjustment

    SECTION 4 ADJUSTMENT Test instruments required for adjustment (1) Digital oscilloscope (100MHz) Standard measuring conditions (2) Jitter meter Power supply voltage DC14.4V(11 to 16V) (3) Digital tester (4) Electric voltmeter Load impedance 4Ω (5) Tracking offset meter Output Level 20kΩ (6) Test Disc : VT501 or VT502 Caution: (7) Extension studs : STDV001-3P...

  • Page 27

    Jitter value conversion table Indicated Indicated Indicated Indicated JIT OUT JIT OUT JIT OUT JIT OUT on the LCD on the LCD on the LCD on the LCD EF56 E972 E38E 10.5 DDAA 13.4 EF22 E93E E35A 10.6 DD76 13.5 EEEE E90A E326...

  • Page 28: Service Mode

    Service mode Note The new HDD of factory shipments is blank. When exchanging new HDD at repair, it needs copy of data from the master HDD by the HDD copy machine. SOURCE Setup to the service mode Turn on the power. Select to the [TUNER] source.

  • Page 29

    Data Read Error History 1.Error History 1.DVD Error 4.System Error 2.Temperature 2.CDCH Error 3.GYRO adjust value 3.Panel Mecha Err Data Read Mode Error History Error logs and data display DVD Error Error log of DVD. E-1 :****** E02 :****** E-2 :****** E03 :****** E-3 :****** E04 :****** E01 :****** E05 :****** DVD Error...

  • Page 30

    NAVI engineer mode Setup to the NAVI engineer mode Turn on the power. Select to the [NAVI] mode Press the key [SEL] [NAVI/AV] [OK] over the two seconds. MENU 1.DIL FILE COPY 4.GPS RAW DATA 2.NAVILOG COPY 5.SIMULATION DIL FILE COPY (For technical examination) 3.SENSOR DATA 6.SYS_DATA COPY Copy the log data file to SD card.

  • Page 31

    ROM correction of the main microcomputer and panel microcomputer The RAM correction of the main microcomputer and panel microcomputer from the CD-R/RW or DVD-R/RW. 4.7.1 Making the disk for ROM correction (1) Prepare the CD-R or CD-RW or DVD-R or DVD-RW. Note: Do not use DVD+R and DVD+RW.

  • Page 32

    DVD unit check mode When change the item must be press the [OK] key up to the execute. Check item list A/D key DVD unit operation LCD indication and contents Start at normal speed CURRENT: Laser current value (After start, it is measured JITTER on the JITTER: Jitter value internal position)

  • Page 33: Troubleshooting

    SECTION 5 TROUBLESHOOTING 16PIN CORD DIAGRAM Black Green Violet GN/BK WH/BK VI/BK GY/BK Gray Blue White Yellow Orange Brown VI/WH BL/WH VI/WH L.GN Light Green Pink BL/WH OR/WH OR/WH Choking Coil MEMORY BL/WH REMOTE BL/WH REVERS VI/WH VI/WH SPEED OR/WH VI/BK GY/BK WH/BK...

  • Page 34

    Victor Company of Japan, Limited AV & MULTIMEDIA COMPANY CAR ELECTRONICS CATEGORY 10-1,1chome,Ohwatari-machi,Maebashi-city,371-8543,Japan (No.MA161) Printed in Japan Downloaded from www.Manualslib.com manuals search engine...

  • Page 35

    SCHEMATIC DIAGRAMS HDD NAVIGATION/DVD RECEIVER KD-NX901 CD-ROM No.SML200506 Area suffix E ------------- Southern Europe Lead free solder used in the board (material : Sn-Ag-Cu, melting point : 219 Centigrade) Contents Block diagram Standard schematic diagrams Printed circuit boards 2-8 to 11 No.MA161SCH...

  • Page 36: Safety Precaution

    Safety precaution Burrs formed during molding may be left over on some parts of the chassis. Therefore, pay attention to such burrs in the case of preforming repair of this system. Please use enough caution not to see the beam directly or touch it in case of an adjustment or operation check.

  • Page 37: Block Diagram

    CODE1 to 3 FM/AM FM TMC PLLDA2 DVD_DATA PLLK2 TUNER TUNER SW4,TRVSW DVD_WS SI/SO DVD_BCK IC781 SW1,SW4 LRCKA JVC BUS SW4,SW5 BCLKA DSPNIT,SD,BUSENABLE,DSP_SDA CH-L CHANGER SDO0 IC11 CH-R DSP_SCK,RFON,RDS_SDA,RDS_SCK FRONT LINE OUT SBRST,DISPSCK,DISPDATA,DISPCE,DETACH,KEYDATA,PS2 PBRK,S.T.REMOCON LCD & Key switch section VIDEO OUT...

  • Page 38: Standard Schematic Diagrams

    Standard schematic diagrams Main section (1/2) To CN501 (SHEET 3) FRONT LINEOUT CN601 STEERINGREMOTE QGB0812L2-90X VIDEO OUT PARKING BREAK L-CH R-CH CN752 RLOUT R1251 R1253 QGA2501C1-08 C2258 Q1251 2SD2114K/VW/-X IC462 100P C1257 100P CN121 GP1FA513TZ0F QGA2501C1-06 C9732 C1259 C2250 100P C9729 C616 C615...

  • Page 39

    Main section (1/2) FM TMC TUNER E-VOL QAU0396-001 R1003 IC102 8.2V R1001 R1002 C1006 4.1V C1007 BD3805F-X DSPINIT 2SC4083/N/-X DSPINIT 1000P 1000P 100P 120P PLLDI2 3.3V PLLDI2 PLLCE2 8.2V AGND DGND PLLCE2 C1011 PLLDA2 2SC4083/N/-X 2.2V 4.5V 3.3V NQR0557-001X PLLDA2 10/16 QAM0747-001 1000P...

  • Page 40

    CPU section (1/2) C5317 C5316 SDRAM R5315 IC511 IC512 K4S561632E-UC75 CN531 K4S561632E-UC75 QGF0534F1-60X C5103 C5109 -ATA_RST 3.3V 3.3V LRCKA 2.9V DQ15 2.9V 2.9V DQ15 2.7V C5104 C5110 ASIC BCLKA 3.3V VDDQ VSSQ 3.3V VDDQ VSSQ CD8V 2.9V DQ14 2.9V 2.9V DQ14 2.9V IC531...

  • Page 41

    CPU section (2/2) DAC for VOICEGUIDE IC591 AK4384ET-X C5902 MCLK R5901 1.7V MCLK DZFL BCLKB R5902 1.7V BICK DZFR C5901 SDATA_1 R5903 5.0V SDTI LRCKB R5904 1.7V 10/16 LRCK C5903 -CODEC_RST R5905 3.3V 2.5V VCOM C5904 2.5V 10/16 SMUTE AOUTL ACKS AOUTR 5.0V...

  • Page 42

    DVD section P3.3V FLASH ROM P3.3V K399 SDRAM D3.3V NQR0502-001X IC399 K4S281632F-UC75 IC398 K301 SG32M90TFIR34A C397 R300 22/6.3 C399 3.2V NQR0502-001X MDQ0 0.1/16 3.1V 3.0V MDQ15 R301 DQ15 C392 EXADT15 1.2V EXADR16 3.2V VDDQ VSSQ EXADT14 R399 MDQ1 0.1/16 MDQ14 P3.3V 0.9V 3.2V...

  • Page 43

    LCD & Key switch section LVB10527 BACK LIGHT WHITE LED RED LED Q8601 R8066 UN2211-X R8065 R8063 1.5k Q8602 UN2211-X R8064 1.5k EN832 QSW1025-001 ENC2 R8062 1.5k ENC1 IC841 Q8301 GP1UX511RK 2SB709A/QR/-X R8319 R8306 R8305 R8304 R8303 R8302 R8301 KEY0 S8311 1.5k S8305...

  • Page 44

    Printed circuit boards Main board Lead free solder used in the board (material : Sn-Ag-Cu, melting point : 219 Centigrade) Forward side Reverse side C606 R628 IC462 C622 IC601 C1258 C1259 C610 CN902 C2258 CN121 CN752 R621 D963 CN901 C601 CN901 C963 C916...

  • Page 45

    CPU board Lead free solder used in the board (material : Sn-Ag-Cu, melting point : 219 Centigrade) Forward side CN531 TP18 TP19 R5517 R5015 R5017 C5028 Q5501 R5018 R5016 R5514 R5020 R5518 C5029 R5021 Q5502 C5031 R5022 C5019 C5012 IC542 R5023 C5407 R5407...

  • Page 46

    Front end board Lead free solder used in the board (material : Sn-Ag-Cu, melting point : 219 Centigrade) Forward side R435 C431 R438 C433 B204 C432 K445 IC411 C533 IC401 C532 R531 C452 C453 C454 R535 K451 K301 C451 R355 C361 R356 C302...

  • Page 47

    Switch board Lead free solder used in the board (material : Sn-Ag-Cu, melting point : 219 Centigrade) Forward side S8307 D8632 D8611 D8618 IC841 S8312 D8606 D8621 R8623 D8622 D8619 D8620 R8611 S8308 S8306 R8619 R8313 R8624 R8612 R8016 R8620 R8015 R8314 R8034...

  • Page 48

    Victor Company of Japan, Limited AV & MULTIMEDIA COMPANY CAR ELECTRONICS CATEGORY 10-1,1chome,Ohwatari-machi,Maebashi-city,371-8543,Japan Printed in Japan (No.MA161SCH) Downloaded from www.Manualslib.com manuals search engine...

  • Page 49: Parts List

    PARTS LIST [ KD-NX901 ] * All printed circuit boards and its assemblies are not available as service parts. Area suffix E ---------------- Southern Europe - Contents - 3- 2 Exploded view of general assembly and parts list (Block No.M1) 3- 6 DVD mechanism assembly and parts list (Block No.MJ)

  • Page 50

    Exploded view of general assembly and parts list Block No. CPU board Switch board Downloaded from www.Manualslib.com manuals search engine...

  • Page 51

    33 117 Main board Downloaded from www.Manualslib.com manuals search engine...

  • Page 52

    General Assembly Block No. [M][1][M][M] Symbol No. Part No. Part Name Description Local  GE20156-001A GEAR BKT UNIT LV40865-002A MINI SCREW (x3) LV40847-002A SPACER FSYH4036-100 SHEET GE30968-002A LEVER BKT UNIT LV40865-002A MINI SCREW (x2) GE30964-003A LOWER LEVER ASS LV35330-001A FRONT BKT ASSY QNZ0664-003 CAR CONNECTOR QAL0587-001...

  • Page 53

    Symbol No. Part No. Part Name Description Local  LV35515-001A KNOB RING LV40848-057A SPACER(P) (x2) LV35516-004A DETACH BUTTON LV44055-001A COMPRESSION SPRING LV35545-001A VOL. RUBBER LV35547-001A VOL.KNOB ASSY LV35508-001A SOURCE WALL (x2) LV35517-007A BUTTON EJECT LV35518-006A BUTTON POWER LV35519-001A PRESET BTN(L) LV35520-001A PRESET BTN(R) LV35521-001A...

  • Page 54

    DVD mechanism assembly and parts list Grease Block No. FMU-JD3-1D = JVS-1003 = MOBIL-1 = JVG-31N = JC-803B = 1401C BACK SIDE AFTER SET PICK UP SA. APPLY GREASE INSIDE The parts without symbol number are not service. Downloaded from www.Manualslib.com manuals search engine...

  • Page 55

    DVD mechanism Block No. [M][J][M][M] Symbol No. Part No. Part Name Description Local  VKZ4539-056 MINI SCREW (x2) QYSPSFT2040ZA TAP SCREW M2 x 4mm LV43481-001A COOLING RUBBER (x2) LV10674-003A CHASSIS FRAME LV30225-0J6A SPACER (x2) VKZ4539-056 MINI SCREW VYSA1R4-056 SPACER LV33684-001A DAMPER(F) (x2) LV33685-001A...

  • Page 56

    Symbol No. Part No. Part Name Description Local  LV43010-001A L.S.GEAR LV43063-001A L.S.COLLAR LV43011-001A THRUST SPRING QYSPSFT2040ZA TAP SCREW M2 x 4mm LV33624-001A HOLDER(M) VKZ4539-056 MINI SCREW (x2) LV21288-001A HOLDER(S) VKZ4539-056 MINI SCREW (x2) LV43064-001A ROD(M) LV43065-001A ROD(S) LV43066-001A SUB SHAFT VKZ4730-002 SPECIAL SCREW (x3)

  • Page 57: Electrical Parts List

    Electrical parts list Main board  Symbol No. Part No. Part Name Description Local Block No. [0][1] Q7002 UN2213-X DIGI TRANSISTOR  Symbol No. Part No. Part Name Description Local Q7501 UN2211-X TRANSISTOR Q7905 UN2211-X TRANSISTOR IC11 SAF7730HV/N114F MA8056/M/-X Z DIODE IC12 PHK04P02T-X POWER MOS FET...

  • Page 58

     Symbol No. Part No. Part Name Description Local  Symbol No. Part No. Part Name Description Local NDC31HJ-220X C CAPACITOR 22pF 50V J C465 NDC31HJ-220X C CAPACITOR 22pF 50V J NDC31HJ-270X C CAPACITOR 27pF 50V J C466 NCB31HK-103X C CAPACITOR 0.01uF 50V K NDC31HJ-101X C CAPACITOR...

  • Page 59

     Symbol No. Part No. Part Name Description Local  Symbol No. Part No. Part Name Description Local C1202 NBE41CM-106X TA E CAPACITOR 10uF 16V M C7802 NBE41AM-476X TA E CAPACITOR 47uF 10V M C1211 NBE21AM-475X TA E CAPACITOR 4.7uF 10V M C7905 NEAG1HM-105X E CAPACITOR...

  • Page 60

     Symbol No. Part No. Part Name Description Local  Symbol No. Part No. Part Name Description Local R129 NRSA63J-100X MG RESISTOR 10Ω 1/16W J R661 NRSA63J-101X MG RESISTOR 100Ω 1/16W J R132 NRSA63J-101X MG RESISTOR 100Ω 1/16W J R901 NRSA63J-103X MG RESISTOR 10kΩ...

  • Page 61

     Symbol No. Part No. Part Name Description Local  Symbol No. Part No. Part Name Description Local R2003 NRSA63J-303X MG RESISTOR 30kΩ 1/16W J R7049 NRSA63J-101X MG RESISTOR 100Ω 1/16W J R2005 NRSA63J-103X MG RESISTOR 10kΩ 1/16W J R7050 NRSA63J-101X MG RESISTOR 100Ω...

  • Page 62

     Symbol No. Part No. Part Name Description Local  Symbol No. Part No. Part Name Description Local R7905 NRSA63J-332X MG RESISTOR 3.3kΩ 1/16W J Q8602 UN2211-X TRANSISTOR R7906 NRSA63J-0R0X MG RESISTOR 0Ω 1/16W J R9801 NRSA63D-244X MG RESISTOR 240kΩ 1/16W D D8001 MA8056/M/-X Z DIODE...

  • Page 63

     Symbol No. Part No. Part Name Description Local  Symbol No. Part No. Part Name Description Local R8006 NRSA63J-331X MG RESISTOR 330Ω 1/16W J R8201 NRSA63J-222X MG RESISTOR 2.2kΩ 1/16W J R8009 NRSA63J-102X MG RESISTOR 1kΩ 1/16W J R8301 NRSA63J-301X MG RESISTOR 300Ω...

  • Page 64

    CPU board  Symbol No. Part No. Part Name Description Local Block No. [0][3] C5207 NCB31CK-105X C CAPACITOR 1uF 16V K  Symbol No. Part No. Part Name Description Local C5301 NBZ0020-107X E CAPACITOR 100uF C5302 NCB31CK-104X C CAPACITOR 0.1uF 16V K C5303 NDC31HJ-100X C CAPACITOR...

  • Page 65

     Symbol No. Part No. Part Name Description Local  Symbol No. Part No. Part Name Description Local R5308 NRSA63J-103X MG RESISTOR 10kΩ 1/16W J CN561 QGF0534F1-50X CONNECTOR FFC/FPC (1-50) R5309 NRSA63J-103X MG RESISTOR 10kΩ 1/16W J CN562 QGF0534F1-50X CONNECTOR FFC/FPC (1-50) R5312 NRSA63J-103X...

  • Page 66

     Symbol No. Part No. Part Name Description Local  Symbol No. Part No. Part Name Description Local C222 NCB31HK-103X C CAPACITOR 0.01uF 50V K C251 NCB31CK-104X C CAPACITOR 0.1uF 16V K R101 NRSA63J-0R0X MG RESISTOR 0Ω 1/16W J C252 NEAF1CM-107X E CAPACITOR 100uF 16V M...

  • Page 67

     Symbol No. Part No. Part Name Description Local  Symbol No. Part No. Part Name Description Local R329 NRSA63J-101X MG RESISTOR 100Ω 1/16W J K426 NQR0022-005X FERRITE BEADS R332 NRSA63J-102X MG RESISTOR 1kΩ 1/16W J K427 NQR0022-005X FERRITE BEADS R333 NRSA63J-163X MG RESISTOR...

  • Page 68

    Packing materials and accessories parts list Block No. No additional / supplemental order of WARRANTY CARDs are available A1 A3 A4 A7 A9 A11 A12 A2 A5 A6 A8 A10 KIT : A13 A14 A15 A16 A17 A18 3-20 Downloaded from www.Manualslib.com manuals search engine...

  • Page 69

    Packing and Accessories Block No. [M][3][M][M] Symbol No. Part No. Part Name Description Local  LVT1294-001B INST BOOK ENG GER FRE DUT LVT1294-002B INST BOOK SPA ITA SWE DAN LVT1294-003A INSTALL MANUAL LVT1294-004A INSTALL MANUAL LVT1294-005A INSTALL MANUAL LVT1294-006A INSTALL MANUAL LV36145-002A ANGLE GAUGE VND3046-001...

Comments to this Manuals

Symbols: 0
Latest comments: