Advertisement
Available languages
Available languages
HDTVI-100 CON
Order number 18.7990
ELECTRONICS FOR SPECIALISTS
ELECTRONICS FOR SPECIALISTS
HD TVI Video Signal Converter
These instructions are intended for install-
ers of video surveillance systems. Please
read the instructions carefully prior to
operation and keep them for later refer-
ence.
1 Applications
This converter is used to convert a TVI video
signal (e. g. from a camera) into an HDMI™,
VGA or composite video signal, e. g. for display
on a monitor or TV set.
2 Safety Notes
The units (converter and power supply unit)
correspond to all relevant directives of the EU
and are therefore marked with
WARNING The power supply unit uses
dangerous mains voltage. Leave
servicing to skilled personnel
only. Inexpert handling may
result in electric shock.
•
The units are suitable for indoor use only.
Protect them against dripping water, splash
water and high air humidity. The admissible
ambient temperature range is 0 – 40 °C.
•
Do not operate the converter and immedi-
ately disconnect the power supply unit from
the mains socket
1. if one of the units is visibly damaged,
2. if a defect might have occurred after a unit
was dropped or suffered a similar accident,
3. if malfunctions occur.
In any case, the units must be repaired by
skilled personnel.
•
For cleaning only use a dry, soft cloth; never
use water or chemicals.
•
No guarantee claims for the units and no
liability for any resulting personal damage or
material damage will be accepted if the units
are used for other purposes than originally
intended, if they are not correctly connected,
or if they are not repaired in an expert way.
VGA OUT
1
ELECTRONICS FOR SPECIALISTS
If the units are to be put out of oper-
ation definitively, take them to a local
recycling plant for a disposal which is
not harmful to the environment.
3 Installation and Operation
The mounting brackets (2) can be used to in-
stall the converter, e. g. on a wall.
1) Use a 75 Ω cable to connect the video source
(e. g. camera) to the BNC jack HD-TVI IN (4).
2) Proceed as required:
– Connect the HDMI input of a monitor or
TV set to the output HDMI OUT (8).
– Connect the VGA input of a computer
monitor to the output VGA OUT (1).
.
– Connect the video input for composite
video signals of a surveillance monitor or
video recorder to the output Composite
OUT (3).
Note: The outputs can be used at the same time.
3) Connect the plug-in power supply provided
to the low-voltage jack DC 12 V (5) and to a
mains socket (230 V/50 Hz). The converter is
switched on; the POWER LED (6) lights up.
4) The LED SIGNAL (6) lights up when a valid
signal is available at the input HD-TVI IN. The
LED HDMI lights up when an HDMI connec-
tion has been made.
5) Briefly press the buttons (7) to increase
() or reduce () the resolution for
the outputs VGA OUT and HDMI OUT
[480p/60 576p/50 720p/60 720p/50
1080i /60 1080i /50 1080p/60 1080p/50].
Note: Not every monitor will support every reso-
lution.
6) The signal at the output Composite OUT also
depends on the setting selected in step 5
(PAL / NTSC). If the image on the monitor
is not fully visible, keep the button or
pressed (> 1 s) to adjust its size (in steps of
2 %, with 80 % as a minimum).
Composite OUT
HD-TVI IN
2
3
4
MONACOR INTERNATIONAL GmbH & Co. KG • Zum Falsch 36 • 28307 Bremen • Germany
Copyright
by MONACOR INTERNATIONAL. All rights reserved.
©
ELECTRONICS FOR SPECIALISTS
ELECTRONICS FOR SPECIALISTS
DC 12 V
5
6
ELECTRONICS FOR SPECIALISTS
4 Reset
1) Disconnect the converter from the power
supply.
2) Keep the button (7) pressed while recon-
necting the converter to the power supply.
3) Release the button.
Basic setting:
Composite OUT = NTSC, maximum size
HDMI OUT, VGA OUT: 480p/60
5 Specifications
Video system: . . . . . . . PAL / NTSC
Input HD-TVI
Resolution: . . . . . . . . . 720p at
25 / 30 / 50 / 60 Hz
1080p at 25 / 30 Hz
Outputs HDMI, VGA
Resolution: . . . . . . . . . 480p at 60 Hz
576p at 50 Hz
720p at 50 / 60 Hz
1080i at 50 / 60 Hz
1080p at 50 / 60 Hz
Output Composite: . . . PAL / NTSC
Power supply: . . . . . . . ⎓ 12 V, 300 mA
via power supply unit
provided and
connected to
230 V/50 Hz
Ambient temperature: 0 ... 40 °C
Dimensions: . . . . . . . . 90 × 33 × 130 mm
Weight: . . . . . . . . . . . 270 g
Subject to technical modification.
POWER RESOLUTION
HDMI OUT
SIGNAL
HDMI
2
7
8
A-1746.99.01.03.2016
ELECTRONICS
Advertisement
