Firmware Update Procedures - Yamaha CDR-HD1000 Service Manual

QQ
3 7 63 1515 0

FIRMWARE UPDATE PROCEDURES

1. Overview
CDR-HD1000 is capable of upgrading both of the system control firmware and the CD-R/W drive firmware by
using the firmware CD-R.
The details of firmware CD-R availability will be provided by a Technical Bulletin.
2. Confirmation of the firmware versions
1. Press the " " key.
2. Press the "MENU" key to enter MENU mode. "Album Edit" is displayed.
3. Rotate the "MULTI JOG" knob to select "Sys. Utility". Press the "MULTI JOG" knob.
4. "Firm. Version" appears is displayed. Press the "MULTI JOG" knob.
The system control firmware version is displayed with its compiled date and time.
The characters shown are scrolled once.
5. Rotate the "MULTI JOG" knob clockwise, the CD-R/W drive firmware version is displayed.
6. Rotate the "MULTI JOG" knob clockwise again, the HDD name is displayed.
7. Press the "MENU" key three times to return to the normal playback mode.
3. Upgrading of the firmware
3.1 Normal Update Operation
1. Press the " " key.
2. Press the "CDR" key to select the CD-R/W drive.
3. Press the " " key to open the disc tray. Load the "firmware CD-R" on the disc tray and press the " " key
to close the tray.
Wait to finish reading the disc.
4. Press the "MENU" key to enter MENU mode. "Album Edit" is displayed.
TE
5. Rotate the "MULTI JOG" knob to select "Sys. Utility".
L 13942296513
Press the "MULTI JOG" knob. "Firm. Version" is displayed.
6. Rotate the "MULTI JOG" knob to select "Firm. Update". Press the "MULTI JOG" knob.
7. "Main FW (CD)" is displayed. Three types of upgrade mode can be selected by rotating the "MULTI JOG"
knob.
(1) "Main FW (CD)" means upgrading the system control firmware from CD-ROM.
(2) "CDRW FW (CD)" means upgrading the CD-R/W drive firmware from CD-ROM.
(3) "All FW (CD)" equal executing "Main FW (CD)" and "CDRW FW (CD)" at the same time.
8. Choose one mode and press the "MULTI JOG" knob.
9. "Push PLAY KEY" is displayed. Press the "
10. "Downloading" is displayed. NEVER TURN OFF THE POWER WHILE "Downloading" IS DISPLAYED.
– "Main FW (CD)" takes about 16 seconds.
– "CDRW FW (CD)" takes about 32 seconds.
– "All FW (CD)" takes about 48 seconds.
11. When finishing the upgrade, "Complete" is displayed and the CDR-HD1000 is rebooted.
12. Confirm that the firmware version has been changed from old to new.
13. If the firmware versions stay old, retry above updating procedures. And if the CDR-HD1000 does not
work well after this updating, see section 3.2 to recover it.
3.2 Recovery mode
The updating procedure fails and the CDR-HD1000 malfunctions. In this case, the CDR-HD1000 has a
recovery updating mode.
3.2.1 The system control firmware recovery
www
If "Firm. Update" is displayed when the CDR-HD1000 has finished the start up sequence, the system control
firmware may be corrupted.
In this case, you can recover the system control firmware by the following procedures.
1. Press the " " key to open the disc tray. Load the "firmware CD-R" on the disc tray and press the " " key
.
to close the tray.
Wait to finish reading the disc.
2. Rotate the "MULTI JOG" knob to select "Firm. Update". Press the "MULTI JOG" knob.
3. "Main FW (CD)" is displayed. Five types of upgrade mode can be selected by rotating the "MULTI JOG"
http://www.xiaoyu163.com
x ao u163
y
i
http://www.xiaoyu163.com
2 9
8
Q Q
3 6 7 1 3 1 5
" key to start update.
co
.
CDR-HD1000
9 4 2 8
0 5 8 2 9 9 4 2 8
m
9 9
9 9
12