English CONTENTS GENERAL POWER TOOL SAFETY WARNINGS ........13 DEMOLITION HAMMER SAFETY WARNINGS ........... 15 SYMBOL ....................... 16 SPECIFICATIONS ..................16 STANDARD ACCESSORIES ............... 16 OPTIONAL ACCESSORIES (sold separately)..........16 APPLICATIONS .................... 17 PRIOR TO OPERATION ................17 HOW TO USE THE DEMOLITION HAMMER..........18 GREASE REPLACEMENT ................
Page 14
English d) Do not abuse the cord. Never use the cord for carrying, pulling or unplugging the power tool. Keep cord away from heat, oil, sharp edges or moving parts. Damaged or entangled cords increase the risk of electric shock. e) When operating a power tool outdoors, use an extension cord suitable for outdoor use.
English Disconnect the plug from the power source and/or the battery pack from the power tool before making any adjustments, changing accessories, or storing power tools. Such preventive safety measures reduce the risk of starting the power tool accidentally. d) Store idle power tools out of the reach of children and do not allow persons unfamiliar with the power tool or these instructions to operate the power tool.
English Properly set the bit holder. At the start of work, confi rm screw tightening. When working at a highly elevated location, pay attention to articles and persons below. 10. Wear protective shoes to protect your feet. SYMBOL WARNING The following show symbols used for the machine. Be sure that you understand their meaning before use.
English Groove digging and edging Scooping Work ○ ○ (1) Cold chisel Overall length: 280, 400 mm (1) Scoop Hammer Grease A ○ 500 g (in a can) 70 g (in a tube) 30 g (in a tube) APPLICATIONS Demolishing concrete, chipping off concrete, grooving, bar cutting, and driving piles. Application examples: Installation of piping and wiring, sanitary facility installation, machinery installation, water supply and drainage work, interior jobs, harbor facilities and other civil engineering work.
English Return grip (A) to its original position, pull the tool and make sure it is locked completely (Fig. 2). Deciding Working Position of Tool The tool can be turned every 30 degrees and can be fi xed at the position of 12 steps. As shown in Fig.
At this time, do not damage or lose the oil seal. Fig. 6 NOTE The Hitachi Electric Hammer Grease A is of the low viscosity type. When the grease is consumed, purchase from the Hitachi Authorized Service Center. MAINTENANCE AND INSPECTION CAUTION Be sure to switch power OFF and disconnect the plug from the receptacle to avoid serious trouble.
Page 20
Replacing supply cord If the replacement of the supply cord is necessary, this has to be done by Hitachi Authorized Service Center in order to avoid a safety hazard.
Page 22
English Item Item Part Name Q’TY Part Name Q’TY FRONT CAP RETAINING RING FOR D14 SHAFT RETAINING RING D28 GEAR COVER DAMPER HOLDER (A) BALL BEARING DAMPER (A) 6203DDCMPS2L DAMPER HOLDER (B) BEARING WASHER GRIP (A) NEEDLE HOLDER ARMATURE ASS’Y SPRING (A) FAN GUIDE STOPPER RING...
Page 23
English Item Item Part Name Q’TY Part Name Q’TY TERMINAL M4.0 CORD SIDE HANDLE NAME PLATE MOUNT TAPPING SCREW D6 × 30 HANDLE BOLT SUPPORT (B) BAND PILLAR TERMINAL SEAL LOCK HEX. SOCKET 100 CONNECTOR 50092 HD. BOLT M5 × 16 101 CONNECTOR 50091 CRANK COVER 502A CASE...
Page 24
● 制造商的售后服务 ;地指表 日立工机商业(中国)有限公司 上海市长宁区遵义南路88号 协泰中心19B-C ● Servicing by manufacturer; list of addresses Hitachi Koki (China) CO., Ltd. Room 19B-C, Shartex Plaza, No.88 Zun Yi Nan Rd., Shanghai 服务中心 日立工机商业(中国)有限公司 上海市长宁区遵义南路88号协泰中心19B-C 制造商 日立工机(马来西亚)有限公司 马来西亚柔佛州士乃第二工业区 Hitachi Koki Co., Ltd. 编号:C99193625 M 发行日期:2015年7月...