Steamer Function; Cleaning; Troubleshooting; Specifications - Unit USP-1060 Instruction Manual

ENGLISH
•
Turn the Relief Valve to down position to release steam.
Note: When cooking fluid food, such as porridge, to avoid squirting up remember not to release
the steam immediately after 3 sound signals. Let the pressure cooker cool down naturally.
Otherwise the fluid food may squirt and result in damage.
•
Remove the plug from the socket.
•
Turn the Handle counter clockwise; open it and take the food out.

STEAMER FUNCTION

The appliance can be used as a Steamer. For this purpose use a special accessory that you
have bought with the appliance – the Steamer .
•
Add some water (1/5 scale) into the Inner Pot. Put the Steamer with kitchen-stuff into the
Inner Pot and close the Lid.
•
Turn the Relief Valve to down position.
•
Power on the appliance with the Power Cord.
•
Choosethebutton "Пароварка».
•
Cooking time is up to your preferences – control the cooking time according to your food
or menu. For this use the "Время давления" button.
• Press the "Отмена" button if you would like to stop the cooking process.

CLEANING

•
Remove the plug from the socket before cleaning wait until the appliance has normal tem-
perature.
•
Take out the Inner Pot and clean it with a sponge or nonmetal soft brush, and then dry it
with towel.
•
Rub the Inner Surface of the appliance with a soft cloth.
• Clean the outer coating of the appliance with a soft slightly wet towel. Never dip it in water
for cleaning or run water over it.
•
Take off the Water Collector and clean it with a wet towel. Put it back as shown in the pic-
ture:
•
Clean the Sealing Gasket, Relief Valve,and Floating Valve with soap water then dry them with
a towel. Aftercleaningputthe parts together again.
Attention! For your safety remember that when the appliance is on it must not contact with
water or other liquids especially the cord and the base of the appliance.
You must not dip the appliance into the water to avoid electric shock, fire or injuring.
Never wash the appliance in a dishwasher!

TROUBLESHOOTING

NO. A Problem
1 Difficult to close the
Lid
2 Difficult to open the
Lid
10
The Cause The Solution
The sealing gasket is Fix the sealing gas-
not fixed well ket well
The pressure inside Let the steam out
is too high turning the relief
valve left or right
3 Steam leaks off the
Lid
4 Indicating lights are
not on
5 E1
E2
E3
E4

SPECIFICATIONS

Model Rated Volt- Power
age
USP-1060D 220-240 V 900 W
Max Pres- Keeping Pre-set
sure warm Tem- Time
perature
80 kPa 70-80 º C 0-24 hours
The head office of the manufacturer :
Exported by:
ENGLISH
There isn't a sealing Put the sealing
gasket in the Lid gasket into the Lid
(see "Appliance use"
paragraph)
The sealing gasket Clean the Sealing
isn't clean Gasket
The sealing gasket is Change a broken or
damaged or de- deformed Sealing
formed Gasket to a new one
in a UNIT service
center
The Lid isn't fixed Fix the Lid properly
properly
The appliance isn't Check the power
powered on cord and the plug
Someotherproblems Send the appliance
to a UNIT service
center
Short circuit of the Send the appliance
sensor to a UNIT service
center
Open circuit of the
sensor
Error of the pressure
regulator
Protection against
overheating
Capacity Diameter Working
Pressure
5 L 22 cm 40-70 kPa
Pressure- Max keep Lifetime
keeping warm Time
Time
1-60 min 0-24 hours 20000 cycles
but not more
than 5 years
from the
date of the
purchase
«UNIT Handelsgesellschaft G.m.b.H.»
131, Gersthofer Str., A-1180, Vienna, Austria
«UNIT Electronics (H. K.) Limited»
3905 Two Exchange Square, 8 Connaught
Place, Central, Hong Kong
11