Summary of Contents for Detection Systems solution ultima
Page 1
A member of the Bosch Group Solution Ultima Operators Manual ISSUE 1.00...
Page 2
Notice of Liability While every precaution has been taken in the preparation of this document, neither Detection Systems nor any of its official representatives shall have any liability to any person or entity with respect to any liability, loss or damage caused or alleged to be caused directly or indirectly by the information contained in this book.
Table Of Contents INTRODUCTION...........................6 KEYPAD INDICATORS ........................7 Zone Indicators..............................7 AWAY Indicator ..............................7 STAY Indicator ..............................9 System Unset ................................9 MAINS Indicator..............................9 Off Indicator / Zone Closed ..........................9 On Indicator / Zone In Alarm ..........................9 FAULT Indicator..............................10 Audible Indications .............................10 SETTING THE SYSTEM........................11 Forced Setting ..............................11 Setting In AWAY Mode............................11 Setting In STAY Mode 1.............................12...
Page 4
FAULT ANALYSIS MODE ........................ 18 Fault Descriptions..............................19 System Fault...............................19 Low Battery..............................19 Date and Time ..............................19 RF Receiver Fail.............................20 Horn Speaker..............................20 Telephone Line Fail ............................20 E2 Fault ................................20 Fuse Fail .................................20 RF Low Battery..............................20 Tamper Fail................................20 Sensor Watch Fault ............................20 RF Sensor Watch Fault ............................20 Communication Fail............................21 DATE AND TIME..........................
Page 5
Operation Of Keypads In Areas ........................27 Area Addressable Keypad Operations ......................27 Master Area Keypad Operations ........................27 DOMESTIC DIALLING........................27 Acknowledging Domestic Calls ..........................27 Programming Domestic Telephone Numbers....................28 Disable Domestic Dialling ...........................28 BASIC PAGER REPORTING ......................29 Basic Pager Display Information ........................29 Site ID Number ..............................29 Zone Status..............................29 System Status ..............................29 GLOSSARY OF TERMS........................31...
Solution Introduction Congratulations on selecting the Solution Ultima control panel to protect you and your property. So that you can obtain the most from your unit, we suggest that you take the time to read through this manual and familiarise yourself with the numerous outstanding operating features of this system.
The AWAY indicator is used to display that the system is Set in AWAY Mode. The AWAY indicator will also flash in unison with the STAY indicator when programming various options throughout the operator’s manual. Detection Systems Operators Manual UK...
Page 8
Refer to page 10 for information on the different methods of setting the system in AWAY Mode. AWAY Indicator Definition System Is Set In AWAY Mode System Is Not Set In AWAY Mode Table 2: AWAY Indicator Operators Manual UK Detection Systems...
On Indicator / Zone In Alarm indicator will display when the system is Set in AWAY Mode and will flash when an alarm occurs. The indicator will reset once a valid user code has been entered. Detection Systems Operators Manual UK...
Walk Test Mode Is Currently Active Or Warning Before One Beep Every Second Automatic Setting Takes Place One Short Beep Every There Is A System Fault Waiting To Be Acknowledged Minute Table 6: Audible Indicators Operators Manual UK Detection Systems...
Two beeps will be heard and the AWAY indicator will display. Exit time will now commence counting. Method Two How To Set The System In AWAY Mode Hold down the # button until two beeps are heard. The AWAY indicator will display and exit time will commence counting. Detection Systems Operators Manual UK...
Any zones that have been programmed to be automatically omitted in STAY Mode 1 will flash until exit time expires. At the end of exit time, the zone indicators will extinguish and the Keypad will give one short beep. Operators Manual UK Detection Systems...
Press the # button when you have selected all zones to be automatically omitted in STAY Mode 2 to exit this mode. Two beeps will be heard and the STAY and AWAY indicators will extinguish. Detection Systems Operators Manual UK...
# button. Two beeps will be heard and the STAY and AWAY indicators will extinguish. If you wish to add or change any further radio remote user codes, repeat this procedure as many times as required. Operators Manual UK Detection Systems...
Press the * button to delete the user code that you have selected. Two beeps will be heard and the STAY and AWAY indicators will extinguish. If you wish to delete any further user codes, repeat this procedure as many times as required. Radio Transmitter Operations Detection Systems Operators Manual UK...
If you wish the Keypads to shutdown and lockout for a period of time (0 – 150 seconds), ask your Engineer to program this. Operators Manual UK Detection Systems...
Repeat Step 2 if more than one zone is required to be omitted until all zone that are required to be omitted have been selected. Press the # button after you have selected all zones to be omitted. Two beeps will be heard and the system will return to the Unset state. Detection Systems Operators Manual UK...
Zone 1 was displayed in Step 1, press and hold button 1 to display which system fault has occurred). To exit and return to the Unset state, press the # button. The FAULT indicator will remain displayed and the Keypad will cease its once a minute beep. Operators Manual UK Detection Systems...
The date and time fault will register every time the system has been powered down. This type of fault will not cause the FAULT indicator to display on the Keypad unless your Engineer has programmed the automatic setting time. Refer to page 20 to program the date and time. Detection Systems Operators Manual UK...
The fault will clear once the RF device in question has successfully transmitted to the RF radio receiver. Whilst you are in fault analysis mode, press and hold button 5 until two beeps are heard will display which RF detection device reported the RF sensor watch fault. Operators Manual UK Detection Systems...
Repeat Step 2 and Step 3 if more than one output is required to be turned on or off. Press the # button to exit this function. Two beeps will be heard and the STAY and AWAY indicators will extinguish. Detection Systems Operators Manual UK...
Press the # button when finished. Two beeps will be heard and the STAY and AWAY indicators will extinguish. Note: To disable the Call Divert Set Sequence, enter the Call Divert sequence as *4 (break) for Step 3. Operators Manual UK Detection Systems...
Note: To disable the Call Divert Unset Sequence, enter the Call Divert sequence as *4 (break) for Step 3. Digit Required Number To Program Digit Required Number To Program 4 Second Pause Break Table 8: Call Divert Set/Unset Dialling Digits Detection Systems Operators Manual UK...
Three beeps will be heard. The last forty events will display one at a time via the Keypad indicators starting from the most recent event. A beep will be heard as each event is displayed. Operators Manual UK Detection Systems...
4 rings and then hang up the telephone. Wait a minimum of 8 seconds before you call the control panel back again). Detection Systems Operators Manual UK...
The group of four “AREA ON/OFF” indicators display the status of each area (i.e. If an indicator is displayed, that area is Set and if the indicator is not displayed, that area is Unset). Note that only Area 1 and Area 2 can be used with the Solution Ultima control panel. Area Display Indicators The group of four “AREA DISPLAY”...
If the call has been successfully acknowledged, a tone of decreasing pitch will be heard. Digit Required Number To Program Digit Required Number To Program 4 Second Pause Break Table 9: Domestic Dialling Telephone Digits Detection Systems Operators Manual UK...
Two beeps will be heard and the STAY and AWAY indicators will begin to flash. Press the * button followed by 4 and the # button (eg. *4#). The STAY and AWAY indicators will now extinguish. Operators Manual UK Detection Systems...
The fourth digit on the system status display indicates when a system fault has occurred at the control panel (0 = System Normal – There is no faults / 1 = System Fault – There is a fault registered by the control panel). Detection Systems Operators Manual UK...
Page 30
The example above shows that the transmission has come from the control panel that has an ID number of 678 and that zone 2 is in alarm. The example also displays that zone 3 has been manually omitted and the system is Set. Operators Manual UK Detection Systems...
A handover zone will act as an instant zone if violated before the Fx zone is violated. Can be used to remotely operate your system via hand held transmitters (Also Hand Held Remote known as RF keyfobs). Control Detection Systems Operators Manual UK...
Page 32
Zones A monitored input used to trigger an alarm condition when violated. 24-Hour Zones A monitored input programmed to trigger an alarm condition when violated when the system is Set or Unset 24-hours a day. Operators Manual UK Detection Systems...
Detection Systems, such as lightning, excessive voltage, mechanical shock, or damage arising out of abuse, alteration, or improper application of the equipment.
Page 34
Ultima Operators Manual Solution Operators Manual UK Detection Systems...
Ultima Operators Manual Solution Installation Notes Installation Company Technicians Name Technicians Telephone Number Installation Date Warranty Expires Panel Software Version Service Notes Detection Systems Operators Manual UK...
Page 36
User Code User Code 10 User Code User Code 11 User Code User Code 12 User Code User Code 13 User Code User Code 14 User Code User Code 15 User Code User Code 16 Operators Manual UK Detection Systems...
Standard Omitting Code To Omit Communication Options Reporting Domestic Reporting Domestic Reporting – No Of Beeps Other System Information Siren Run Time Minutes Can Your System Be If Yes, Engineer’s Code Serviced By Another Technician Detection Systems Operators Manual UK...
Page 38
RF Device 13 ID Number RF Device 6 ID Number RF Device 14 ID Number RF Device 7 ID Number RF Device 15 ID Number RF Device 8 ID Number RF Device 16 ID Number Operators Manual UK Detection Systems...