CognitiveTPG A798 User Manual page 21

*** A798 – Diagnostics Form ***
*** A795 - Diagnostics Form ***
Model number
Serial number
Model number
Boot Firmware
Serial number
Revision
CRC
Boot Firmware
P/N
Revision
Flash Firmware
CRC
Revision
P/N
CRC
Flash Firmware
P/N
Revision
CRC
H/W parameters
P/N
Flash Memory Size
Flash Logos/Fonts
H/W parameters
Flash User Storage
Flash Memory Size
SRAM Size
Flash Logos/Fonts
Head Setting
Flash User Storage
Paper Type Name
Flash Perm'nt Fonts
Color Density Adj
Flash Journal Size
Print Density (Mono)
SRAM Size
Max Speed
Head setting
Paper Width
Pre-Heating
Max Power
Print Density
Knife
Max Speed
Partial Cut
Paper Width
Paper Low Sensor
Max Power
Knife
Comm. Interface
Partial Cut
RX Buffer Size
Paper Low Sensor
Interface type
Parameters
Comm. Interface
Baud Rate
RX Buffer Size
Data Bits
Interface type
Stop Bit
Parameters
Parity
Baud Rate
Flow Control
Data Bits
Reception Errors
Stop Bit
Alternate DTR/DSR : Disabled
Parity
Flow Control
Resident Code Pages
Reception Errors
USB Driver Type
USB Packet w/Error
Available Paper Types
Resident Code Pages
Logo (s) defined
User Char(s) defined
Logo(s) defined
User Char(s) defined
Journal Unused
To enter Printer Config Menu :
1) Flip DIP switch #1 down
2) Reset the printer, while holding
the Paper Feed button down
To enter Printer Config Menu :
1) Flip DIP switch #1 down
2) Reset the printer, while holding
the Paper Feed button down
Print test and Configuration menu samples. Samples will vary depending on the printer model.
(Shown approximately 60% of size)
Short clicks are used in the main menu selections.
10/2013
*********
*******************************
: A795-2119
: A012251287
Select a sub-menu :
: A798-720D-TD00
: C073400014
: V1.02
: 76EB
: 189-1076076A
: V3.02
: D554
: V1.13
: 189-7940505A
: AB62
: 189-7950290A
: V3.01
Enter code, then hold Button DOWN
: 4FFF
at least 1 second to validate
: 189-7940497A
: 2 Mbyte
: 1024 kbytes
: 0 kbytes
: 2 Mbytes
: 256 kbytes
: 64 kbytes
: D
: 64 kbytes
: Type 5, Version 0
: 0 kbytes
: 100 %
: 1152 kbytes
: 100 %
: 128 kbytes
: 100 mm/sec
: C
: 80 mm
: Disabled
: 55 W
: 100%
: Enabled
: 150 mm/sec
: 135 steps
: 80 mm
: Disabled
: 55 W
: Enabled
: 125 steps
: 4096
: Disabled
: RS232/USB
: 115200
: 4096
: 8
: RS232/USB
: 1
: NONE
: 115200
: DTR/DSR
: 8
: Ignore
: 1
: NONE
: DTR/DSR
: 437, 850, 852, 858
: Ignore
860, 863, 865, 866
: Printer Class
1252, 862, 737
: Reject
: 00.00 01.00 05.00
: 437, 850, 852, 858
01.90 01.92 01.93
860, 863, 865, 866
1252, 862, 737, 857
: YES
1251, 1255, KZ-1048
Current Printer tallies are
: NO
}
printed after the Diagnostic
: NO
information and will vary
: NO
: 1152 kbytes
per printer use.
A798-UG00001 Rev. E1
Chapter 4: Using the Printer
**********
MAIN MENU
- EXIT -> 1 click
- Print Current Configuration -> 2 clicks
- Set Communication Interface -> 3 clicks
- Set Diagnostics Modes -> 4 clicks
- Set Emulation/Software Options -> 5 clicks
- Set Hardware Options -> 6 clicks
- Set Paper Type -> 7 clicks
When the printer is configured for USB, this
location will show either: "USB Driver Type: Printer
Class", or "USB Driver: Comm Class".
A798 Thermal Receipt Printer: User Guide
21