Track Programming For Recording; Automatic Tape Programming - Yamaha CDC-685 Owner's Manual

TRACK PROGRAMMING FOR RECORDING
" I /
- i:::.J::i·-
/ I "
(OFF)
9~~1~
:::I.i:::I . . . . . . . . .
~ ------....l
TAPE
~
You can also enter the tape's total possible recording
time manually.
Example: For a C-64 tape (32 minutes on each side)
You can select any of four tape lengths by pressing the
TAPE button.
REPEAT
Q
The unit automatically programs tracks for side A and
side B separately considering the tape's total time.
*
The programmed track numbers and the total number
of tracks for side A and B are displayed for a short
time.
• It is recommended that you use a tape that is slightly longer
in length than the CD you are recording, because the
programmed tracks on a CD may not fit properly into the
time allowed on each half of the tape.
• CD synchronized recording function can be used if your tape
deck is compatible with it. In this case, in step 5 and 6, press
the SYNCHRO button and then press the
C>
button.
Recording automatically begins. (For details, refer to page
16.)
fa
Begin recording on the tape deck and press the
[>
button at the same time.
m
The unit will pause at the end of side A of the
tape.
Turn the tape over to side B. Resume recording and, at
the same time, press the
[>
or
DO
button.
n
Press the REPEAT button.
" I /
' 1 ."
- J:··I···.-
/ I "
4
TAPE
Q
6
Select the disc.
3
<l
DISC SKIP
C>
~ :~
....
\ /
' _ • • 1
~
Enter the tape's total possible recording time
(tape length).
The unit will automatically program tracks on a disc with
the original order of tracks unchanged.
_ _I
D
Stop the unit.
This convenient feature can be used to program tracks for
recording to tape. By only memorizing the tape's total
possible recording time, the unit will automatically program
tracks or help you to program tracks so they will fit onto the
tape with the least amount of unrecorded space remaining at
each end of the tape.
The peak level searching function of this unit is useful for
adjusting recording level on the tape deck. (Refer to page
21.)
E-17
TRACK PROGRAMMING FOR RECORDING
" I /
- i:::.J::i·-
/ I "
(OFF)
9~~1~
:::I.i:::I . . . . . . . . .
~ ------....l
TAPE
~
You can also enter the tape's total possible recording
time manually.
Example: For a C-64 tape (32 minutes on each side)
You can select any of four tape lengths by pressing the
TAPE button.
REPEAT
Q
The unit automatically programs tracks for side A and
side B separately considering the tape's total time.
*
The programmed track numbers and the total number
of tracks for side A and B are displayed for a short
time.
• It is recommended that you use a tape that is slightly longer
in length than the CD you are recording, because the
programmed tracks on a CD may not fit properly into the
time allowed on each half of the tape.
• CD synchronized recording function can be used if your tape
deck is compatible with it. In this case, in step 5 and 6, press
the SYNCHRO button and then press the
C>
button.
Recording automatically begins. (For details, refer to page
16.)
fa
Begin recording on the tape deck and press the
[>
button at the same time.
m
The unit will pause at the end of side A of the
tape.
Turn the tape over to side B. Resume recording and, at
the same time, press the
[>
or
DO
button.
n
Press the REPEAT button.
" I /
' 1 ."
- J:··I···.-
/ I "
4
TAPE
Q
6
Select the disc.
3
<l
DISC SKIP
C>
~ :~
....
\ /
' _ • • 1
~
Enter the tape's total possible recording time
(tape length).
The unit will automatically program tracks on a disc with
the original order of tracks unchanged.
_ _I
D
Stop the unit.
This convenient feature can be used to program tracks for
recording to tape. By only memorizing the tape's total
possible recording time, the unit will automatically program
tracks or help you to program tracks so they will fit onto the
tape with the least amount of unrecorded space remaining at
each end of the tape.
The peak level searching function of this unit is useful for
adjusting recording level on the tape deck. (Refer to page
21.)
E-17