Cleaning Hard Floors - Kenmore 680.14100410 Use & Care Manual

CLEANING HARD FLOORS

CAUTION
!
To reduce the risk of injury from moving parts,
unplug cleaner.
Read "before using the machine" instructions.
1. Make sure you have the correct brushes on the
machine. For hard floors these are the dark
bristled hard scrub brushes. To change brushes
follow instructions at the end of section 2.
2. Attach the hard floor squeegee as shown in fig.
3.5
3. Fill clean water tank and detergent tank as
instructed in section 2.
4. Set wash High/Normal setting knob to the
normal position (fig 3.1).
5. Turn switch on in the "Carpet/Hard Floor"
position. The brushes will start turning, and the
vacuum motor will start.
6. While depressing the solution button at the top
of the handle pull the machine on a straight line
backwards slowly and steadily. You should see
the dirty water flowing into the dirty water tank (if
you do not see it, turn machine off and refer to the
troubleshooting section at the end of this
manual). This machine is designed to clean in
one pass. You may have to repeat if the floor is
heavily soiled. Release the solution button 8 to 10
inches before the end of the pass.
7. Push the machine forward to start another
pass and repeat step 5. Consecutive passes
should overlap about 1" (Fig 3.2). Repeat until
you covered the entire area.
8. When the clean water tank is empty, the sound
of the pump will change and dirty water will stop
flowing into the dirty water tank. Turn machine off,
empty dirty water tank and refill clean water tank
and detergent tank as per section 2 in this
manual.
9. Make a "dry pass" over the area to extract the
most amount of moisture from the floor. To only
extract moisture, do not press down on the
Solution button when passing the Cleaner over
the just-cleaned area.
10. When cleaning is complete, turn machine off.
Empty the clean water tank, and empty and clean
dirty water tank as instructed in section 2.
Remove and rinse brushes.
3.5
CAUTION
!
Do not use the carpet cleaner on unsealed
hardwood floors.
To prevent damage to wood floor, follow the
flooring manufacturer´s cleaning
recommendations.
If using cleaner on sealed wood floors, inspect
floor surface for worn finish, bare wood or
separated joints. It is not recommended to
use the cleaner on wood floors if any of these
conditions exist.
11
2. COMO USAR SU LAVA ALFOMBRAS
DESCRIPCIÓN
2.1
1. Manija
2. Ganchos guarda cable
3. Botón para abatir la manija
4. Perilla reguladora de detergente
5. Botón accionador de detergente
6. Manija de carga
7. Tanque de recuperación
8. Acceso para conexión
del accesorio tapicero
9. Boquilla de succión
10. Botón de encendido/apagado
11. Tanque de agua limpia
12. Tanque para detergente
13. Pedal para liberar la manija
14. Cepillos
15. Manguera
16. Accesorio tapicero
17. Charola porta accesorios
2
3
4
13
BOTÓN DE
2.2
ENCENDIDO Y
APAGADO
2.2 Para encender su
lava alfombras presione
el botón hacia abajo,
para apagarla presione
el botón nuevamente.
10
15
16
17
12
11
1
7
5
14
6
8
9
PEDAL PARA
2.3
LIBERAR MANIJA
2.3 Pise el pedal (A)
para poner la manija
en posición de trabajo.
La manija no se bloquea
en una sola posición, se
mantiene móvil para
manejarla fácilmente. A
20