Door Reversal - Kenmore 461.99130 Owner's Manual

Door Reversal

TOOLS REQUIRED
Phillips #2 screwdriver and an adjustable wrench.
WARNING!
Excessive Weight Hazard
Use two or more people when moving the wine
cooler.
1. Unplug the wine cooler and lay the unit on its back.
2. Unscrew the two Leveling Legs; one from the
bottom hinge on right and one from the left side of the
unit (see Fig. 3 and Fig. 4 for locations).
3. Remove the bottom hinge by unscrewing its three (3)
screws (Fig. 2).
NOTE: Keep this hinge in a safe place incase
you need to return to a right hand door swing.
4. Carefully remove the door and set aside by sliding
it downward off of the top hinge pin.
5. Remove the two (2) plastic screw caps located on top
of the hinge cover (Fig. 1).
6. Remove the top hinge cover by removing its two (2)
screws (Fig. 1).
7. Remove the top hinge by unscrewing its three (3)
screws (Fig. 1)
8. Remove the plastic door pin cap from the top left
side of the door and transfer it to the right side of the
door.
9. Remove the three (3) Plastic Screw Caps from the
top left side of the cabinet and transfer them to the
top right side of the cabinet (Fig.6).
10. Install the top hinge on the left side of the unit and
secure with three (3) screws. (Fig. 1)
11. Install the hinge cover back on the top hinge and
secure with two (2) screws. (Fig. 1)
12. Install the two (2) plastic screw caps on the hinge
cover. (Fig. 1)
13. Carefully install the door on the cabinet (insert upper
door into top hinge pin).
Fig.5
Left Bottom
Hinge Assembly
14. Using the left-side bottom hinge supplied with your
unit (Fig.5): insert the hinge pin into the bottom of the
door, then align the holes in the hinge with the holes
in the cabinet and secure hinge to cabinet with three
(3) screws.
15. Install the Leveling Leg formerly attached to the
right bottom hinge (Fig.4) onto the new left bottom
hinge, and install the Leveling Leg from the former
left side position into the right side position (Fig.3).
16. Check door alignment, door seal and ensure the door
lock slides comfortably into the lock chamber. Tighten
all hinge screws.
I M P O R TA N T !
Allow the unit to stand upright for at-least 1 hour
before putting the unit into operation.
Fig.1
Fig.6
Top Hinge
Plastic Screw Caps
Assembly
Fig. 2
Right Bottom
Hinge Assembly
Fig.3
Leveling Leg
Fig. 4
Leveling Leg for Bottom Hinge
8
Instrucciones de Operación
Características de su
Heladera para Vinos
1
5
1. Trabas con llave a prueba de niños.
2. Juntas Magnéticas de la Puerta: Las
juntas ajustadas mantienen todo el poder
de enfriamiento y los niveles de humedad.
3. Puerta de vidrio templado: Polarización
para proteger contra radiación UV pero
permite ver fácilmente el interior.
Especificaciones
Ancho 19,44" / 493mm
Alto 33,06" / 840mm
Profundidad 24,13" / 613mm
29
2
3
4
6
4. Estantes con bordes de acero
inoxidable
5. Controles Electrónicos Dobles: Para
regular independientemente la temperatura
de ambos compartimientos de la heladera
para vinos.
6. Patas Niveladoras
Temperatura 39,2~64,4°F / 4~18°C
Peso Neto 97 libras / 44 kg