Further, ViewSonic reserves the right to revise this publication and to make changes from time to time in the contents hereof without obligation of ViewSonic to notify any person of such revision or changes.
Specification Front Panel Function Control Description Circuit Description Adjustment Procedure Troubleshooting Flow Chart Recommended Spare Parts List Exploded Diagram and Exploded Parts List Block Diagram 10. Schematic Diagrams 11. PCB Layout Diagrams ViewSonic Corporation VX1935wm-1 Confidential - Do Not Copy...
4. Power Supply Requirements The external AC power operating range shall be from 90 to 264Vac ViewSonic Corporation VX1935wm Confidential - Do Not Copy...
Page 5
Power Source, or be applied exemption. (14) The LCD module is designed so that the CFL in it is supplied by Limited Current Circuit. Do not connect the CFL in Hazardous Voltage Circuit. ViewSonic Corporation VX1935wm Confidential - Do Not Copy...
Page 6
3.Place the monitor on a clean and soft foam 3.Placing the monitor on foreign objects. That pad. could scratch the surface of the panel or cause “Mura”. ViewSonic Corporation VX1935wm Confidential - Do Not Copy...
≦ 8% (Maxmum output @ 1KHZ) Signal to Noise Ratio 50 dB Frequency response 500 Hz – 20 Khz SPL. 80 ± 3 dB / 10.W‧0.5m 3.5 mm stereo jacks Line input connection ViewSonic Corporation VX1935wm Confidential - Do Not Copy...
Page 8
Typical = 5ms (Tr = ms,Tf = 10%-90% @ Ta=25°C Maxmum = 10ms (Tr = ms,Tf = Panel Defects Please see Panel Quality Specifications. *1 Test conditions: Inverter Current=6.5mA, Color Temp.=User Mode, OSD: Brightness=100%, Contrast=100% ViewSonic Corporation VX1935wm Confidential - Do Not Copy...
Performance no 35 1280×960 @50Hz 49.405 49.853 83.000 P 1680 128 200 1280 72 991 guarantee 36 1280×960 @60Hz 60.000 60.000 108.000 P 1800 112 312 1280 96 1000 3 36 960 ViewSonic Corporation VX1935wm Confidential - Do Not Copy...
Page 10
● Under DOS mode (640 x 350, 720 x 400 & 640 x 400), it should recall factory setting when execute “Auto Image Adjust” ● The monitor needs to do “Auto Adjust” the first time when a new mode is detected(See section “0-Touch™ Function Actions”) ViewSonic Corporation VX1935wm Confidential - Do Not Copy...
[▲] Up Arrow Button Note: Power Button, Button 1 and Button 2 must be one-shot logic operation. (i.e. there should be no cycling) Reaction Time OSD must fully appear within 0.5s after pushing Button 1 ViewSonic Corporation VX1935wm Confidential - Do Not Copy...
Page 12
REMARK: There may need to select “Fine Tune” function on “Manual Image Adjust” to optimized Performance for various VGA tolerance. Contrast / Brightness : To adjust the Contrast of the video and the backlight currency. ViewSonic Corporation VX1935wm Confidential - Do Not Copy...
Page 13
To select the signal sources of the Analog or Digital. Audio Adjust : To adjust the audio volume and mute. Color Adjust : To select the color temperature sRGB, 9300°K, 7500°K ,6500°K, 5400°K or user color. ViewSonic Corporation VX1935wm Confidential - Do Not Copy...
Page 14
Horizontal Size: To adjust the horizontal pixel clock of the video. H./V. Position: To adjust the horizontal and vertical position of the video. Fine Tune: To adjust the delay time of data and clock. Sharpness: To select the picture sharpness of display. ViewSonic Corporation VX1935wm Confidential - Do Not Copy...
Page 15
OSD Timeout: To set the displaying time of OSD. OSD Background :To select video background brightness. Memory Recall: Restore default settings of Clock, H./V. Position, Phase, Contrast, Brightness, Color temperature, OSD position, OSD timeout and Sharpness, Volume. ViewSonic Corporation VX1935wm Confidential - Do Not Copy...
LCD monitors with resolutions up to WXGA. It is configured with an integrated triple-ADC/PLL, a high quality scaling engine, an on-screen display controller, a built-in output clock generator, and LVDS display interface. To further reduce system costs, the TSUM17AK also integrates intelligent power management . ViewSonic Corporation VX1935wm Confidential - Do Not Copy...
Vertical of video should be adjustable to Thickness be within the screen frame. RGB Color RGB Color Contrast of each R, G, B, color Figure 4, 5, Performance Intensities should be normal. ViewSonic Corporation VX1935wm Confidential - Do Not Copy...
Page 18
Fine Line Morie Pattern (Figure1) Gray Scale Pattern (Figure2) Horizontal & Vertical Thickness Pattern R. Color Pattern (Figure 4) (Figure 3) G. Color Pattern (Figure5) B. Color Pattern (Figure 6) ViewSonic Corporation VX1935wm Confidential - Do Not Copy...
Page 19
Test Pattern: Burn In Mode (Refer to Chapter 3-1. Hot Keys for Function Controls) - Make sure the F/W is the latest version. 1.5.4 DDC Test Pattern: EDID program - Make sure it can pass test program. 1.5.5 Fine Tune and Sharpness ViewSonic Corporation VX1935wm Confidential - Do Not Copy...
Page 20
- Make sure there is audio output. - Make sure that audio function (volume≦80%) is working without noise and resonance. - Make sure that the sound of right and left speakers are in balance. ViewSonic Corporation VX1935wm Confidential - Do Not Copy...
Page 21
- Fixture for Firmware Upgrade - VGA Cable - PC (Personal Computer) - ISP Tool - Firmware Upgrade Program - One additional monitor for checking the program execution ISP tool instruction 15 pin D-Sub LPT cable ViewSonic Corporation VX1935wm Confidential - Do Not Copy...
Page 22
ISP tool Use 12V adapter ISP connect method ISP Download program procedure Hardware Connect status: ViewSonic Corporation VX1935wm Confidential - Do Not Copy...
Page 23
AR : Analog /RSDS DR : Analog + Digital / RSDS Panel type : 150MX17A01 Firmware version : R30.2 Change Panel (Version update) 1. Check : Monitor model 2. Check : Firmware version ViewSonic Corporation VX1935wm Confidential - Do Not Copy...
Page 24
(ps.2) If change panel : (Form HSD150MX17A00 change to HSD150MX17A01) Panel type : 150MX17A00 => 150MX17A01 Firmware change : HC154_AL_150MX17A00R30.2 => HC154_AL_150MX17A01R30.2 5. Update final firmware version : HC154_AL_150MX17A01R30.3 6. Update EDID code : HC154_150MX17A01_EDID_A.txt ViewSonic Corporation VX1935wm Confidential - Do Not Copy...
Page 25
DR : Analog + Digital / RSDS Panel type : 150MX17A01 Firmware version : R30.2 3. Change scaler board. 4. Update final firmware version : HC154_AL_150MX17A01R30.3 5. Update EDID code : HC154_150MX17A01_EDID_A.txt ViewSonic Corporation VX1935wm Confidential - Do Not Copy...
Page 26
3. Enforce Mstar ISP Utility Window's Connect function, and Device Type's Dialog window will be opened ,then press "Sure " on Dialog window. 4. Enforce Mstar ISP Utility window 之 Read function. ViewSonic Corporation VX1935wm Confidential - Do Not Copy...
Page 27
6. Choose the path and file of Binary code ,and Program Bin Ready Dialog window will be opened, then press "Sure" on Dialog window. 7. Enforce Mstar ISP Auto function of Utility window. ViewSonic Corporation VX1935wm Confidential - Do Not Copy...
Page 28
8. Enforce Mstar ISP Utility window "Run"and write in the data . 9. After writing in the data , Enforce Dis Connect function of Mstar ISP Utility window and the burn in procedure will be completed. ViewSonic Corporation VX1935wm Confidential - Do Not Copy...
- PC - RS232 cable - VGA Cable or DVI Cable DDC Card (D8330) RS-232 Cable VGA Cable Step 1 : Select VA903b in Working Model column to show EDID data on left ViewSonic Corporation VX1935wm Confidential - Do Not Copy...
Page 30
Step 2 : Modify the column of Week of Manufacture and Year of Manufacture and ID serial Number then press “2B” button for changing serial number data. Step 3 : You will see the result as follows. ViewSonic Corporation VX1935wm Confidential - Do Not Copy...
Page 31
(Figure 5 ~ 6) User’s manual / Warranty card / CD package Base short side turn upward Panel side forward D-Sub/ DVI Power Code / cables Audio Cable (Figure 5) (Figure 6) ViewSonic Corporation VX1935wm Confidential - Do Not Copy...
Page 32
1.1 Detach Base Unit from the monitor. 1.2 Remove the ARM cover. 1.3 Unfasten six screws to remove the ARM. 2. Disassembly of Front Cover and Rear Cover 2.1 Unscrew ten screws to remove Rear Cover. ViewSonic Corporation VX1935wm Confidential - Do Not Copy...
Page 33
2.2 Unfasten four screws to remove Hinge folder bracket. 2.3 Unfasten six screws to remove the D-sub / DVI connector and Power socket. 2.4 Unfasten five screws and disconnect Inverter cables from panel to remove the shielding. ViewSonic Corporation VX1935wm Confidential - Do Not Copy...
Page 34
2.5 Unfasten four screws to remove the Keypad board. 2.6 Unfasten eight screws to remove Power Inverter board and D-sub/DVI connect board. Power Inverter Board D-sub/DVI connect board Cables 2.7 Remove the Front Bezel. ViewSonic Corporation VX1935wm Confidential - Do Not Copy...
Please change panel line or vertical line The backlight is OFF Please check inverter wire if properly connected Please change panel or P/I/A board (ps) Display panel have block bar Please change panel ViewSonic Corporation VX1935wm Confidential - Do Not Copy...
Page 36
Please check if panel wire is loose connection or not Please change panel Audio output error Please change P/I/A board (ps) (ps) : P/I/A board Power/Inverter/Audio board ViewSonic Corporation VX1935wm Confidential - Do Not Copy...
Remark 2: All revised RSPLs with newly added items or any change made should be highlighted and correlated with the ECN/ECR approved by ViewSonic Corporation. This is to eliminate repeated cross checks of each item between this version and prior versions.
Page 38
BOM LIST ( VX1935wm-1 ) ViewSonic Model Number: VS11307 Serial No. Prefix: Q8Y Rev: 1a Item ViewSonic P/N Ref. P/N Description Location Universal number# Q'ty 72-01193502G000 VX1935 China Packing assy A-00008042 72-01193501G000 VX1935 USA Packing assy 70-VX193500G000 VX1935 KEY BOARD ASS’Y (Lead Free)
Page 39
Item ViewSonic P/N Ref. P/N Description Location Universal number# Q'ty 39-VX193500G000 VX1935 Key Board PCB Ver : 2.0 34-04170017G000 AL Foil W40*L200*T0.1mm 33-R3910506G000 CABLE STEREO PHONE(JHEN VEI) 33-R3910503G000 DVI CABLE 1800MM(JHEN VEI) 33-R3910501G000 CABLE SIGNAL D/15P-15P(M)1800MM-JHEN VEI 33-E3980005G000 PWR CORD CHN 250V/10A 1.8M 3C BLK"Linetek"...
11. PCB Layout Diagrams TOP SIDE ViewSonic Corporation VX1935wm-1 Confidential - Do Not Copy...
Page 55
BOTTOM ViewSonic Corporation VX1935wm-1 Confidential - Do Not Copy...
Page 56
SILKSCREEN-BOTTOM ViewSonic Corporation VX1935wm-1 Confidential - Do Not Copy...
Page 57
SILKSCREEN-TOP ViewSonic Corporation VX1935wm-1 Confidential - Do Not Copy...
Page 58
MASK-TOP ViewSonic Corporation VX1935wm-1 Confidential - Do Not Copy...
Page 59
MASK-BOTTOM ViewSonic Corporation VX1935wm-1 Confidential - Do Not Copy...
Page 60
SMD-TOP ViewSonic Corporation VX1935wm-1 Confidential - Do Not Copy...
Page 61
DRILL DRAWING ViewSonic Corporation VX1935wm-1 Confidential - Do Not Copy...
Page 62
ViewSonic Corporation VX1935wm-1 Confidential - Do Not Copy...
Page 63
ViewSonic Corporation VX1935wm-1 Confidential - Do Not Copy...
Page 64
ViewSonic Corporation VX1935wm-1 Confidential - Do Not Copy...
Page 65
ViewSonic Corporation VX1935wm-1 Confidential - Do Not Copy...
Page 66
ViewSonic Corporation VX1935wm-1 Confidential - Do Not Copy...
Page 67
ViewSonic Corporation VX1935wm-1 Confidential - Do Not Copy...
Page 68
Company: Add: Tel: Fax: E-mail: After completing this form, please return it to ViewSonic Quality Assurance in the USA at facsimile 1-909-839-7943. You may also e-mail any suggestions to the Director, Quality Systems & Processes (marc.maupin@viewsonic.com) ViewSonic Corporation VX1935wm-1 Confidential - Do Not Copy...
Need help?
Do you have a question about the VX1935wm-1 and is the answer not in the manual?
Questions and answers