Mini-itx intel 7th/6th gen. core i7/i5/i3/pentium/celeron processor (133 pages)
Summary of Contents for Protech Systems ISA-562LF
Page 1
USER’S MANUAL ISA-562LF Half Size CPU Card With VGA/Sound/LAN ISA-562LF M2...
Page 2
Copyright Notice ISA-562LF Half Size CPU Card With VGA /Sound/LAN OPERATION MANUAL COPYRIGHT NOTICE This operation manual is meant to assist both Embedded Computer manufacturers and end users in installing and setting up the system. The information contained in this document is subject to change without any notice.
Copyright Notice FCC NOTICE This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment.
Contents TABLE OF CONTENTS CHAPTER 1 INTRODUCTION About This Manual ............System Specification ............Safety Precautions ............CHAPTER 2 HARDWARE CONFIGURATION Jumper & Connector Quick Reference Table ....Component Locations ............ How to Set the Jumpers ..........COM Port Connector ……..…………………………... RS232/422/485(COM2) Selection ........
CHAPTER INTRODUCTION This chapter gives you the information for ISA-562LF. It also outlines the System specification. Section includes: About This Manual System Specifications Safety precautions Experienced users can skip to chapter 2 on page 2-1 for Quick Start. Page:1-1...
Chapter 1 Introduction 1-1. ABOUT THIS MANUAL Thank you for purchasing our ISA-562LF Intel® processor, Half Size Card enhanced with VGA / Sound/ LAN, which is fully PC / AT compatible. ISA- 562LF provides faster processing speed, greater expandability and can handle more task than before.
One additional 4-pin External keyboard connector UNIVERSAL SERIAL BUS : Universal Serial Bus Connector on board Supports up to two USB 2.0 ports. BUS SUPPORT : One ISA Bus One PC/104 One Compact Flash Bus ′ Page: 1-3 ISA-562LF USER S MANUAL...
Page 10
Monitor Voltage, CPU Temperature and Cooling Fan. IRDA PORT : One 5-pin Infrared connector Supports IrDA v1.0 SIR protocol. LED INDICATOR : HDD LED, Power LED. SOUND : Realtek ALC202A (AC’ 97 Codec) ′ Page: 1-4 ISA-562LF USER S MANUAL...
3. Disconnect power when you change any hardware devices. For instance, when you connect a jumper or install any cards, a surge of power may damage the electronic components or the whole system. ′ Page: 1-5 ISA-562LF USER S MANUAL...
You can connect PIN1 & PIN2 to create one setting and shorting. You can either connect PIN2 & PIN3 to create another setting. The same jumper diagrams are applied all through this manual. The figure below shows what the manual diagrams look and what they represent. ′ Page: 2-4 ISA-562LF USER S MANUAL...
Page 16
Jumper Block looks like this JUMPER SETTINGS 2 pin Jumper close(enabled) Looks like this 3 pin Jumper 2-3 pin close(enabled) Looks like this Jumper Block 1-2 pin close(enabled) Looks like this ′ Page: 2-5 ISA-562LF USER S MANUAL...
COM2 : COM2 Connector The COM2 is selectable as RS-232/422/485. The pin assignment is as follows : ASSIGNMENT RS-232 RS-422 RS-485 COM2_DCD COM2_RXD COM2_TXD COM2_DTR COM2_DSR RTSN COM2_RTS RTSP COM2_CTS CTSP COM2_RI CTSN ′ Page: 2-6 ISA-562LF USER S MANUAL...
This connector is used to set the COM2 function. The jumper settings are as follows : COM 2 Jumper Settings Jumper Function (pin closed) Illustrations RS-232 open RS-422 1-2, 3-4, 9-10 RS-485 1-2, 5-6, 7-8 *** Manufactory default --- RS-232. ′ Page: 2-7 ISA-562LF USER S MANUAL...
For Y-Cable user, please set the jumper same as AT keyboard. The jumper settings are as follows: JUMPER SETTING DEVICE JUMPER (pin closed) TYPE ILLUSTRATION AT KEYBOARD PS/2 MOUSE *** Manufactory default -- AT Keyboard. ′ Page: 2-9 ISA-562LF USER S MANUAL...
JPAENL1 (5,7) : Hard Disk Drive LED Connector The pin assignment is as follows : ASSIGNMENT +3.3V HD_LED 2-11. ATX POWER BUTTON JPANEL1 (10,12) : ATX Power Button The pin assignment is as follows : ASSIGNMENT V5SB PWB_SIOJ ′ Page: 2-10 ISA-562LF USER S MANUAL...
2-13. POWER LED CONNECTOR JPAENL1 (4,6,8) : Power LED Connector The pin assignment is as follows: ASSIGNMENT PLED 2-14. KEYLOCK CONNECTOR JPAENL1 (13,14) : Keylock Connector The pin assignment is as follows: ASSIGNMENT KEYLOCKJ ′ Page: 2-11 ISA-562LF USER S MANUAL...
IRTX2 IRRX2 JIRDA1: IrDA (Infrared) Connector. The pin assignments are as follows: ASSIGNMENT IRRX IRTX 2-16. CPU FAN CONNECTOR JCFAN1 : CPU Fan connector The pin assignment is as follows: ASSIGNMENT +12V FAN1 ′ Page: 2-12 ISA-562LF USER S MANUAL...
Note: To clear CMOS data, user must power-off the computer and set the jumper to “Clear CMOS” as illustrated above. After five to six seconds, set the jumper back to “Normal” and power-on the computer. ′ Page: 2-13 ISA-562LF USER S MANUAL...
Chapter 2 Hardware Configuration 2-18. VGA CONNECTOR VGA1 : VGA CRT Connector The pin assignments are as follows: ASSIGNMENT GREEN BLUE VGA IIC DATA HSYNC VSYNC VGA IIC CLK ′ Page: 2-14 ISA-562LF USER S MANUAL...
34-pin flat cable to attach the FDD on the board, and the other side is attaches two FDDs. The pin assignments are as follows : ASSIGNMENT ASSIGNMENT RWCJ DS1J INDEXJ MOAJ DSBJ DSAJ MOBJ DIRJ STEPJ WENJ TRAK0J RDATAJ HEADJ DSKCHGJ ′ Page: 2-16 ISA-562LF USER S MANUAL...
As to link the Printer to the card, you need a cable to connect both DB25 connector and parallel port. The pin assignments are as follows : ASSIGNMENT ASSIGNMENT PRNSTRBJ PRNALFJ PRND0 PRNERRORJ PRND1 PRNPARINITJ PRND2 PRNSLCTINJ PRND3 PRND4 PRND5 PRND6 PRND7 PRNACKJ PRNBUSY PRNPE PRNSLCTJ ′ Page: 2-17 ISA-562LF USER S MANUAL...
CGND CGND CGND LAN LED Indicator: Left side LED: Green Color On 10/100 LAN Speed Indicator No LAN switch/hub connected Right side LED: Yellow Color Blinking LAN Message Active No LAN Message Active ′ Page: 2-18 ISA-562LF USER S MANUAL...
2-24. ATX POWER CONNECTOR PW1 : ATX Power Connector The pin assignments are as follows: ASSIGNMENT +12V V5SB PSON -12V 2-25. 5VSB CONNECTOR J6 : 5VSB Connector The pin assignments are as follows: ASSIGNMENT V5SB PSON ′ Page: 2-19 ISA-562LF USER S MANUAL...
2-26. AT/ATX POWER SELECTION JP1, JP14 : AT/ATX Power Selection The selections are as follows : JUMPER SETTING JUMPER (pin closed) FUNCTION ILLUSTRATION JP14 Open Open *** Manufacturing Default is set as ATX. ′ Page: 2-20 ISA-562LF USER S MANUAL...
Chapter 2 Hardware Configuration 2-30. RESET/NMI WATCHDOG SELECTION JP18 : Reset/NMI Watchdog Selection The selections are as follows: JUMPER JUMPER SETTING FUNCTION ILLUSTRATION (pin closed) RESET ***Manufacturing Default is set as Reset. ′ Page: 2-22 ISA-562LF USER S MANUAL...
2-32. LVDS PANEL VOLTAGE SELECTION JP7 : LVDS Panel Voltage Selection. The selections are as follows: JUMPER SETTING JUMPER SELECTION ILLUSTRATION LVDS_VCC3 1-3, 2-4 LVDS_VCC5 3-5, 4-6 ***Manufacturing Default is set as LVDS_VCC3. ′ Page: 2-24 ISA-562LF USER S MANUAL...
CHAPTER SOFTWARE UTILITIES This chapter comprises the detailed information of VGA driver, LAN driver, and Flash BIOS update. It also describes how to install the watchdog timer configuration. Section includes: VGA Driver Utility Flash BIOS Update LAN Driver Utility Sound Driver Utility Intel®...
Chapter 3 Software Configuration 3-1. INTRODUCTION Enclosed with our ISA-562LF package is our driver utility, which may comes in a form of a CD ROM disc or floppy diskettes. For CD ROM disc user, you will only need some of the files contained in the CD ROM disc,...
Page 38
Under the Windows 98 system, after rebut computer, there will have two error messages appear, “Can’t find ikch8xx.cat and isb8xx.cat”, just skip the messages, they will not cause any effects. ′ Page:3-3 ISA-562LF USER S MANUAL...
Utility Disk for system BIOS and VGA BIOS update. 3-3-2. To update VGA BIOS for LCD Flat Panel Display: As ISA-562LF user, you have to update the VGA BIOS for your specific LCD flat panel you are going to use. For doing this, you need two files.
Page 40
File Name to Program: H562xxxx.bin Checksum: XXXXX Reset System or Power off to accomplish update process! F1: Reset F10: Exit Please reset or power off the system, and then the Flash BIOS is fully implemented. ′ Page:3-5 ISA-562LF USER S MANUAL...
Chapter 3 Software Configuration 3-4. LAN DRIVER UTILITY 3-4-1. Introduction ISA-562LF is enhanced with LAN function that can support various network adapters. Installation programs for LAN drivers are listed as follows: For more details on Installation procedure, please refer to Readme.txt file found on LAN DRIVER UTILITY.
“D:\Sound\pathname” refers to the full path to the source files. 3. Click on the OK button or press the ENTER key. 4. Click on the “Next” and OK prompts as they appear. 5. Reboot the system to complete the driver installation. ′ Page:3-7 ISA-562LF USER S MANUAL...
3. Click Setup.exe file for utility installation. 4. Follow the instructions on the screen to complete the installation. 5. Once installation is completed, shut down the system and restart in order for the changes to take effect. ′ Page:3-8 ISA-562LF USER S MANUAL...
5. Double Click “USB Root Hub”. 6. Select “Driver”. 7. Click “Install” to install the driver. 8. Follow the instructions on the screen to complete the installation. 9. Click “Finish” after the driver installation is complete. ′ Page:3-9 ISA-562LF USER S MANUAL...
1. Enable watchdog timer and set 30 sec. as timeout interval ;----------------------------------------------------------- Mov dx, 2eh ; Enter to extended function mode Mov al, 87h Out dx, al Out dx, al ;----------------------------------------------------------- Mov al, 07h ; Select Logical Device 8 of watchdog timer ′ Page:3-10 ISA-562LF USER S MANUAL...
Page 46
Dec dx ; Set timeout interval as 30seconds and start counting Mov al, 0f6h Out dx,al Inc dx Mov al, 30 Out dx,al ;----------------------------------------------------------- Dec dx ; Exit the extended function mode Mov al, 0aah Out dx,al ′ Page:3-11 ISA-562LF USER S MANUAL...
CHAPTER AWARD BIOS SETUP This chapter shows how to set up the Award BIOS. Section includes: Introduction Entering Setup The Standard CMOS Features The Advanced BIOS Features The Advanced Chipset Features Integrated Peripherals Power Management Setup PNP/PCI Configuration PC Health Status Frequency Control Load Fail-Safe Defaults Load Optimized Defaults...
4-1. INTRODUCTION This chapter will show you the function of the BIOS in managing the features of your system. The ISA-562LF Intel® processor, Half Size Card is equipped with the BIOS for system chipset from Award Software Inc. This page briefly explains the function of the BIOS in managing the special features of your system.
You may use the cursor the up/down keys to highlight the individual menu items. As you highlight each item, a brief description of the highlighted selection will appear at the bottom of the screen. ′ Page: 4-3 ISA-562LF USER S MANUAL...
< Hour >, < Minute >, and < Second >. Use 24 hour clock format, i.e., for PM numbers, add 12 to the hour. For example: 4: 30 P.M. You should enter the time as 16:30:00. ′ Page: 4-4 ISA-562LF USER S MANUAL...
Page 51
Auto: The BIOS automatically determines the optimal mode. Normal: Maximum number of cylinders, heads, sectors supported are 1024, 16 and 63. Large: For drives that do not support LBA and have more than 1024 cylinders. ′ Page: 4-5 ISA-562LF USER S MANUAL...
Page 52
BASE MEMORY: Displays the amount of conventional memory detected during boot up. EXTENDED MEMORY: Displays the amount of extended memory detected during boot up. TOTAL MEMORY: Displays the total memory available in the system. ′ Page: 4-6 ISA-562LF USER S MANUAL...
Page 53
1024 65535 1023 1024 65535 1023 1024 65535 1023 1024 65535 1023 1024 65535 1023 65535 1023 65535 1024 65535 1023 1024 65535 1023 65535 65535 65335 AUTO Award Hard Disk Type Table ′ Page: 4-7 ISA-562LF USER S MANUAL...
This item allows you to choose the Virus Warning feature for IDE Hard Disk boot sector protection. If this function is enabled and someone attempt to write data into this area, BIOS will show a warning message on screen and alarm beep. ′ Page: 4-8 ISA-562LF USER S MANUAL...
Page 55
This item sets the number of times a second to repeat a key stroke when you hold the key down. TYPEMATIC DELAY (MSEC): The item sets the delay time after the key is held down before it begins to repeat the keystroke. ′ Page: 4-9 ISA-562LF USER S MANUAL...
Page 56
Setup freely. OS SELECT FOR DRAM >64MB : Select the operating system that is running with greater than 64MB or RAM on the system. You may choose OS2 or Non-OS2. ′ Page: 4-10 ISA-562LF USER S MANUAL...
The default settings have been chosen because they provide the best opera- ting conditions for the system. The only time you might consider making any changes would be if you discovered that data was being lost while using your system. ′ Page: 4-11 ISA-562LF USER S MANUAL...
Page 58
VIDEO BIOS CACHEABLE: Select Enabled allows caching of the video BIOS, resulting in better system performance. However, if any program writes to this memory area, a system error may result. ′ Page: 4-12 ISA-562LF USER S MANUAL...
Page 59
PANEL TYPE: (depend on chipset) This field allows user to decide the LVDS panel resolution. The available choices are: 640x480 18bits, 800x600 18bits, 1024x768 18bits, 1280x1024 36bits, 1400x1050 36bits, 1600x1200 36bits, and 1024x768 24bits. ′ Page: 4-13 ISA-562LF USER S MANUAL...
If bios setup menu item supports USB device boot, it will cause Win9x detects the same storages twice when the system is rebooted, and USB HDD will fail. Note: this cause just happen under Win9x, the phenomenon is a limitation. ′ Page: 4-14 ISA-562LF USER S MANUAL...
Page 61
DMA driver (Windows 95 OSR2 or a third-party IDE bus master driver). If you hard drive and your system software both support Ultra DMA/33, select Auto to enable BIOS support. ′ Page: 4-15 ISA-562LF USER S MANUAL...
Page 62
Select Enabled if your system contains a Universal Serial Bus (USB) controller and you have a USB keyboard. 4. USB Mouse Support Select Enabled if your system contains a Universal Serial Bus (USB) controller and you have a USB Mouse. ′ Page: 4-16 ISA-562LF USER S MANUAL...
Page 63
Disabled. 2. Onboard Serial Port 1/2 Select an address and corresponding interrupt for the first and second serial ports. 3. UART Mode Select This item allows you to select UART mode. ′ Page: 4-17 ISA-562LF USER S MANUAL...
Page 64
Select a DMA channel for the parallel port for use during ECP mode. 12. PWRON After PWR-Fail This item allows you to select if you want to power on the system after power failure. The choice: Off, On, Former-Sts. ′ Page: 4-18 ISA-562LF USER S MANUAL...
ACPI FUNCTION: This item allows the user to set the ACPI suspend type to be used. POWER MANAGEMENT: This item allows you to select the Power Management mode. ′ Page: 4-19 ISA-562LF USER S MANUAL...
Page 66
When the system enters a Soft-off mode (Standby power exist but system is not working), it will wake up system when specific signals occurred. The BIOS monitors the system for “activity” to determine when to enable power management. ′ Page: 4-20 ISA-562LF USER S MANUAL...
Page 67
Enabled, even when the system is in a power down mode. (1) Primary IDE 0 (2) Primary IDE 1 (3) Secondary IDE 0 (4) Secondary IDE 1 (5) FDD, COM, LPT Port ′ Page: 4-21 ISA-562LF USER S MANUAL...
Normally, you leave this field Disabled. Select Enabled to reset Extended System Configuration Data (ESCD) when you exit Setup if you have installed a new add-on and the system configuration has caused such a serious conflict that the operating system cannot boot. ′ Page: 4-22 ISA-562LF USER S MANUAL...
Page 69
Descriptions on each item above are as follows: 13. IRQ-n Assigned to: You may assign each system interrupt a type, depending on the type of device using the interrupt. PCI/VGA PALETTE SNOOP: Leave this field at Disabled. ′ Page: 4-23 ISA-562LF USER S MANUAL...
This item shows you the current CPU temperature. CURRENT CPU FAN SPEED: This item shows you the current CPUFAN speed. CURRENT SYSTEM FAN SPEED: This item shows you the current System FAN speed. ′ Page: 4-24 ISA-562LF USER S MANUAL...
Enabling pulse spectrum spread modulation changes the extreme values from spikes to flat curves, thus reducing EMI. This benefit may in some cases be outweighed by problems with timing- critical devices such as a clock-sensitive SCSI device. ′ Page: 4-25 ISA-562LF USER S MANUAL...
When you press <Enter> on this category, you get a confirmation dialog box with a message similar to the following: Load Optimized Defaults ( Y/N ) ? N Pressing "Y" loads the default values that are factory setting for optimal performance system operations. ′ Page: 4-26 ISA-562LF USER S MANUAL...
PASSWORD DISABLED!!! Press any key to continue... Press the < Enter > key again and the password will be disabled. Once the password is disabled, you can enter Setup freely. ′ Page: 4-27 ISA-562LF USER S MANUAL...
You may always call up the setup program at any time to adjust any of the individual items by pressing the <Del> key during boot up. ′ Page: 4-28 ISA-562LF USER S MANUAL...
►Integrated Peripherals ►Power Management word Quit Without Saving (Y/N)? N ►PnP/PCI Configura etup ►PC Health Status Saving Esc : Quit ↑↓→← : Select Item F10 : Save & Exit Setup Abandon all Datas ′ Page: 4-29 ISA-562LF USER S MANUAL...
Appendix B Technical Summary INTERRUPT MAP ASSIGNMENT System TIMER Keyboard Cascade Serial port 2 Serial port 1 Available Floppy Parallel port 1 RTC clock Available Available Available PS/2 Mouse Math coprocessor IDE1 IDE2 ′ Page: B-3 ISA-562LF USER S MANUAL...
Extension memory low byte Extension memory high byte Reserved for extension memory low byte Reserved for extension memory high byte Date Century byte Information Flag 34-3F Reserve 40-7f Reserved for Chipset Setting Data ′ Page: B-4 ISA-562LF USER S MANUAL...
TIMER & DMA CHANNELS MAP Timer Channel Map : Timer Channel Assignment System timer interrupt DRAM Refresh request Speaker tone generator DMA Channel Map : DMA Channel Assignment Available Available Floppy Available Cascade Available Available Available ′ Page: B-5 ISA-562LF USER S MANUAL...