Safety instructions Before you switch ON Installation the appliance Following installation, ensure Please read the operating that the back and installation instructions of the dishwasher is not carefully. They contain freely accessible (protection important information on how to against contact due to hot install, use and maintain surface).
Safety instructions If the dishwasher is installed Do not install the appliance below or above other near heat sources (radiators, domestic appliances, follow heat storage tanks, cookers the information for installation or other appliances which in combination with generate heat) and do not a dishwasher install under a hob.
Safety instructions Damage In the case of free-standing appliances, ensure that the The appliance may be baskets are not overloaded. repaired and opened up by a If the appliance technician only. To do this, is not in a cavity and a side disconnect the appliance panel is accessible, the door from the power supply.
Protection of the environment Keep children away from Protection of the detergents and rinse aid. environment These may cause chemical burns in the mouth, throat i o n P r o t e c t o f t e n v i r o n m e n t and eyes or asphyxiation.
Getting to know your appliance Appliance interior Getting to know your appliance 1" Interior light * G e t t i t o k n o w y o u r a p p l i a n c 1* Cutlery drawer Diagrams of the control panel 12 Top basket and the interior of the appliance can be...
Water softening system/Special salt To change the setting: Water softening 1. Press programme button 3. system/Special salt Each time the button is pressed, the set value increases by one level; W a t e r s o f t e n i s y s t e m / S p e c i s a l t when the value of :...
Rinse aid 1. Open the screw-type cap of the Switching off salt refill compartment 1R. indicator/water softening 2. Fill the tank with water (only required system when switching on the appliance for S w i t c h i n g o f f w a t e r s o f t e n i n g s y s t e m the first time).
Rinse aid 1. Open the dispenser 1j by pressing 1. Open the door. and lifting the plate on the cover. 2. Switch on ON/OFF switch (. 3. Hold down programme button # and press START button ` until : ..is indicated on the digital display.
Utensils Loading the dishwasher Utensils U t e n s i 1. Remove large food remnants. It is not necessary to prerinse utensils Not suitable under running water. 2. Place the utensils so that Cutlery and utensils made of wood. –...
Utensils Cups and glasses Pans Top basket 12 Bottom basket 1b Note Utensils must not be placed above the Heavily soiled utensils (pans) should tablet collecting tray 1B. These may be placed in the bottom basket. The block the lid of the detergent dispenser more powerful spray jet provides and prevent it from opening fully.
Utensils Cutlery drawer F olding spikes * F o l d i n g s p i k e s Arrange the cutlery in the cutlery drawer * depending on model 1* as illustrated. Separately arranged The spikes can be folded down to utensils are easier to remove after improve arrangement of pans, bowls washing.
Detergent Adjusting the height of the 3. To raise the basket, hold the basket on the sides of the upper edge and basket lift it up. 4. Before re-inserting the basket again, The height of the upper utensils basket ensure that it is at the same height 12 can be adjusted in 3 stages to on both sides.
Detergent Adding detergent 2. Close the cover on the detergent dispenser by sliding it up until the lock engages without difficulty. 1. If the detergent dispenser 9" is still closed, press the lock 9* to open the detergent dispenser. Pour detergent into the dry detergent dispenser 9"...
Detergent Combination detergent Notes You will obtain optimum rinsing Apart from conventional detergents and drying results by using solo (Solo), a number of products are offered detergents and applying salt with additional functions. These and rinse aid separately. products contain not only the detergent If programmes are short, tablets but also rinse-aid and salt replacement may not have full cleaning effect...
Overview of programmes Overview of programmes p r o g r a m m e s O v e r v i e w o f The max. possible number of programmes is illustrated in this overview. The corresponding programmes and their arrangement can be found on the fascia.
Additional options § Programme selection Half load * H a l f l o a d You can select a suitable programme If you have only a few items to wash according to the type of utensils and (e.g. glasses, cups, plates), you can degree of soiling.
Operating the appliance Switching on the appliance If the appliance is installed at eye-level, with flush furniture front, the light point is not visible. 1. Turn on the tap fully. This function can be changed as 2. Open the door. follows: 3.
Operating the appliance T imer programming * To change the setting, T i m e r p r o g r a m m i n g 1. Press programme button 3. Each time the button is pressed, the set * depending on model value increases by one level;...
Operating the appliance 1. Open the door. About the Eco drying function: When Eco drying is activated in the 2. Switch on ON/OFF switch (. Eco 50° programme, the door opens 3. Hold down programme button # automatically when the programme and press START button ` ends.
Cleaning and maintenance Never use a steam cleaner to clean your Filters dishwasher. The manufacturer is not liable for any consequential damage. The filters 1Z keep large foreign Regularly wipe the front of the appliance objects in the rinsing water away from and fascia with a damp cloth;...
Fault, what to do? Spray arms Fault, what to do? F a u l t , w h a t d o ? Limescale and contaminants in the rinsing water may block nozzles and Experience has shown that you can bearings on the spray arms 1: and rectify most faults which occur in daily operation yourself.
Fault, what to do? Waste water pump 6. Check impeller wheel and remove any foreign objects. 7. Place cover in the original position Large food remnants or foreign objects and press down until it engages which were not captured by the filters (click).
Fault, what to do? Fault table Fault Reason Remedial action “Check water supply” Supply hose kinked. Install supply hose without kinks. display 8 lights up. Tap turned off. Turn on the tap. Tap jammed or calcified. Turn on the tap. Flow rate must be min.
Fault, what to do? Fault Reason Remedial action A different error code is A technical fault has probably Switch off the appliance with the ON/OFF switch (. After a short time restart the indicated on the digital occurred. display. appliance. to : If the problem recurs, turn off the tap and pull out the mains plug.
Fault, what to do? Fault Reason Remedial action Utensils not dry. No or too little rinse aid in the Refill rinse aid. dispenser. Programme selected without Select programme with drying (see drying. “Overview of programmes”, “Programme sequence”). Water collecting in depressions Arrange utensils in a sloping position, on the utensils and cutlery.
Fault, what to do? Fault Reason Remedial action Food remnants on the Utensils placed too closely Arrange utensils with adequate clearance utensils. together, utensils basket between them ensuring that the spray jets overfilled. can reach the surface of the utensils. Prevent contact points.
Fault, what to do? Fault Reason Remedial action Water stains on plastic Droplet formation on plastic Use a more intensive programme (more parts. surface is physically unavoidable. water changes). After drying, water stains are Arrange utensils in a sloping position. visible.
Fault, what to do? Fault Reason Remedial action Coloured (blue, yellow, Film formation consisting of Can be partly removed with machine brown), difficult to remove ingredients from vegetables (e.g. cleaner or by mechanical cleaning. Coatings to non-removable coatings cabbage, celery, potatoes, are harmless.
Fault, what to do? Fault Reason Remedial action Initial or existing, Glasses not dishwasher-proof, Use dishwasher-proof glasses. irreversible clouding of only suitable for dishwasher. Avoid long steam phase (standing time after glass. wash cycle ends). Use wash cycle at lower temperature. Set water softening system according to the water hardness (if required one setting lower).
Fault, what to do? Fault Reason Remedial action Door does not open Eco drying deactivated. Activate Eco drying (see chapter “Operating automatically at the end of the appliance”). the Eco 50° programme. Button lock has been activated. * Deactivate button lock (see chapter “Safety information”).
Fault, what to do? Fault Reason Remedial action Appliance stops in the Door not closed properly. Close the door. programme or programme Do not place utensils or fragrance Check whether rear panel is being pressed is interrupted. dispenser in the tablet collecting in, e.g.
Customer service Customer service Installation and connection C u s t o m e r s e r v i c e If you are unable to rectify the fault, l a t i o n I n s t a l a n d c o n n e c t i please contact your customer service.
Installation and connection Delivery Installation Your dishwasher has been checked The required installation dimensions can thoroughly in the factory to ensure that it be found in the installation instructions. is in working order. This may cause Level the appliance with the aid of the small water stains.
Installation and connection Drinking water connection Setting hot water: 1. Open the door. 2. Switch on ON/OFF switch (. 1. Fasten the drinking water connection to the tap according 3. Hold down programme button # to the installation instructions using and press START button ` the enclosed parts.
Installation and connection Electrical connection Removing the appliance Connect the appliance to an Also observe alternating current only, ranging from the sequence of worksteps here. 220 V to 240 V and 50 Hz or 60 Hz 1. Disconnect the appliance from via a correctly installed socket with the power supply.
Installation and connection Transportation Protection against frost P r o t e c t i o n a g a i n s t f r o s t ( E m p t y i n g t h e a p p l i a n c e ) Empty the dishwasher and secure loose If the appliance is in a room where there parts.
*9001059271* 9001059271 en (9506) 640MV...