Table of Contents
Advertisement
QQ
3 7 63 1515 0
Step 2 : Setting up the remote commander
Inserting the batteries
Insert two R6 (size AA) batteries
by matching the + and – on the
batteries to the diagram inside the
battery compartment.
Insert the negative (–) end first,
then push in and down until the
positive (+) end clicks into the
position.
Using the remote
commander
You can use this remote
commander to operate this VCR
and a Sony TV. Buttons on the
remote commander marked with a
dot (•) can be used to operate your
Sony TV. If the TV does not have
the
symbol near the remote
sensor, this remote commander
will not operate the TV.
To operate
Set
the VCR
a Sony TV
TE
L 13942296513
12
Setting up the remote commander
To
Switch to Teletext*
Select the sound
Use FASTEXT*
1
Call up the on-screen display
Change the Teletext page*
Switch to/from wide mode of a Sony wide TV (For
other manufactures' wide TVs, see "Controlling
other TVs with the remote commander (SLV-
SE840G only)" below.)
Notes
• With normal use, the batteries should last about three to six months.
• If you do not use the remote commander for an extended period of time, remove
the batteries to avoid possible damage from battery leakage.
• Do not use a new battery together with an old one.
• Do not use different types of batteries together.
• Do not leave the remote commander in an extremely hot or humid place.
• Do not drop any foreign object into the remote casing, particularly when replacing
the batteries.
• Do not expose the remote sensor to direct light from the sun or lighting apparatus.
Doing so may cause a malfunction.
• Some buttons may not work with certain Sony TVs.
*
1
SLV-SE840G only
Controlling other TVs with the remote commander (SLV-
SE840G only)
The remote commander is preprogrammed to control non-Sony TVs. If your
TV is listed in the following table, set the appropriate manufacturer's code
number.
1
Set
/
www
Hold down ?/1, and enter your TV's code number using the programme
2
number buttons. Then release ?/1.
Now you can use the following TV control buttons to control your TV:
?/1, t TV/VIDEO, programme number buttons, - (ten's digit),
PROG +/–, 2 +/–, a (TV), / (Teletext), FASTEXT buttons,
.
(wide)*, MENU*,
* These buttons may not work with all TVs.
14
Setting up the remote commander
http://www.xiaoyu163.com
Remote sensor
/
1
2
3
4
5
6
7
8
9
0
/
to
and point at the remote sensor at the VCR
and point at the remote sensor at the TV
Press
1
/ (Teletext)
AUDIO MONITOR
FASTEXT buttons
DISPLAY
c / C
1
(wide)
at the top of the remote commander to
.
x
ao
y
i
M
/
m
/
<
/
,
*, and OK*.
http://www.xiaoyu163.com
8
TV control buttons
To
Set the TV to standby mode
Select an input source: aerial in or line in
Select the TV's programme position
Adjust the volume of the TV
Switch to TV (Teletext off)*
Q Q
3
6 7
1 3
Code numbers of controllable TVs
If more than one code number is listed, try entering them one at a time until
you find the one that works with your TV.
To switch to wide mode, see the footnotes below this table for the applicable
code numbers.
Manufacturer
Sony
Akai
Ferguson
Grundig
Hitachi
JVC
Loewe
Mivar
NEC
Nokia
*
1
Press
*
2
Press
*
3
Press
select the wide picture you want and press OK.
Tip
• When you set your TV's code number correctly while the TV is turned on, the TV
turns off automatically.
Notes
• If you enter a new code number, the code number previously entered will be
erased.
• If the TV uses a different remote control system from the one programmed to work
with the VCR, you cannot control your TV with the remote commander.
• When you replace the batteries of the remote commander, the code number may
change. Set the appropriate code number every time you replace the batteries.
u163
.
1-3
2 9
9 4
2 8
?/1
AUDIO MONITOR
DISPLAY
t TV/VIDEO
1
2
3
Programme
4
5
6
number
7
8
9
buttons
-
0
/
2 +/–
PROG +/–/
a
c / C
FASTEXT buttons
Press
?/1
t TV/VIDEO
Programme number buttons,
-, PROG +/–
2 +/–
a (TV)
1
1 5
0 5
8
2 9
9 4
Setting up the remote commander
Code number
Manufacturer
01*
, 02
Panasonic
1
68
Philips
52
Saba
10*
1
, 11*
1
Samsung
24
Sanyo
33
Sharp
45
Telefunken
09, 70
Thomson
66
Toshiba
15, 16, 69*
3
(wide) to switch the wide picture mode on or off.
(wide), then press 2 +/– to select the wide picture mode you want.
(wide). The menu appears on the TV screen. Then, press M/m/</, to
m
co
Setting up the remote commander
9 9
2 8
9 9
continued
13
Code number
17*
, 49
1
06*
1
, 07*
1
, 08*
1
12, 13
22, 23
25
29
36
43*
2
38
15
Hide quick links:
Advertisement
Table of Contents
