Ariens 921045 Operator's Manual
  1. Manuals
  2. Brands
  3. Ariens Manuals
  4. Snow Blower
  5. 921045
  6. Operator's manual

Ariens 921045 Operator's Manual

Deluxe series
Hide thumbs Also See for 921045:
Table of Contents

Advertisement

Quick Links

Deluxe Series
Models
921045 – Deluxe 24
(SN 000101 +)
921046 – Deluxe 28
(SN 000101 +)
921047 – Deluxe 30
(SN 000101 +)
921048 – Deluxe 28 SHO
(SN 000101 +)
E10
Sno-Thro
Operator's Manual
Manuel du Utilisateur
ENGLISH
FRANÇAIS
®
•
05001300A
4/16
Printed in USA

Advertisement

Table of Contents
loading

Related Manuals for Ariens 921045

Summary of Contents for Ariens 921045

  • Page 1 Sno-Thro ® Operator’s Manual Manuel du Utilisateur Deluxe Series Models 921045 – Deluxe 24 (SN 000101 +) 921046 – Deluxe 28 (SN 000101 +) 921047 – Deluxe 30 (SN 000101 +) 921048 – Deluxe 28 SHO (SN 000101 +) ENGLISH •...

  • Page 2: Table Of Contents

    TABLE OF CONTENTS WELCOME ..... . 1 Change Engine Oil....13 Check Auger Gearcase Oil .

  • Page 3: Welcome

    WELCOME Congratulations on your purchase and welcome to the Ariens family! Every snow thrower in the Ariens lineup is designed for long-lasting and unsurpassed performance. We are confident your machine will be part of your family for many years to come.

  • Page 4: Safety

    • BECOME ALERT! penalties. Emission controls and components • OBEY THE MESSAGE! can only be adjusted by an Ariens Company dealer or an authorized engine SIGNAL WORDS manufacturer's service center. Contact your The safety alert symbol above and signal Ariens Company Equipment Retailer...

  • Page 5: Safety Decals

    4. Notice Safety Decal Descriptions NOTICE: Indicates information or procedures 1. CAUTION! that are considered important but not hazard related. If not followed, property damage could result. Danger! 5. Important IMPORTANT: Indicates general reference information worthy of special attention. SAFETY DECALS Only use clean-out tool to The safety decals on your machine are visual clear blockages.

  • Page 6: Safety Rules

    SAFETY RULES 2. DANGER! The following safety instructions are based on the B71.3 specifications of the American National Standards Institute in effect at the Danger! time of production. Training Read, understand and follow all instructions on the machine and in the manual(s) before operating this unit.
  • Page 7 Handle fuel with care; it is highly flammable. Thrown objects can cause injury. Check for weak spots on docks, ramps or floors. Avoid • Use an approved fuel container. uneven work areas and rough terrain and • Never add fuel to a running engine or hot stay alert for hidden hazards.
  • Page 8 Disengage attachment when not in use and Maintenance and Storage when traveling from one work area to Secure unit so it will not tip over during another. maintenance. Disengage power to the auger / impeller Before cleaning, removing clogs or making when snow thrower is transported or not in any inspections, repairs, etc., disengage use.
  • Page 9 Avoid starting or stopping on a Accessories slope. Do not park unit on a slope unless absolutely necessary. When parking on a Use only Ariens Company-recommended slope always block the wheels. attachments or accessories that are Do not operate near drop-offs, ditches, or designed for your unit and that are embankments.

  • Page 10: Controls & Features

    CONTROLS & FEATURES Model 921047 Models 921045, 921046, 921048 Models 921045, Models 921047, 921046 921048 Figure 3 1. Engine Key 14. Shear Bolt (2) 2. Primer Bulb 15. Attachment Clutch Lever 3. Fuel Tank and Cap 16. Traction Drive Clutch Lever 4.

  • Page 11: Engine Key

    Figure 7 Stop SPEED SELECTOR LEVER See Figure 8. Controls the speed of forward and reverse travel. Models 921045, 921046, 921048 Figure 4 PRIMER BULB Model 921047 Adds fuel to engine for easier start on cold engines. FUEL VALVE See Figure 5.

  • Page 12: Attachment Clutch Lever (Right Side)

    Auger continues to turn until both clutch levers are released. DISCHARGE CHUTE ROTATION HANDLE Models 921045, 921046, 921048 See Figure 11. Rotates discharge chute left or right to control snow discharge. Figure 12 EN - 10...

  • Page 13: Heated Hand Grip Switch

    E85 blended fuels; the engine is not E20 / 3. Engage attachment clutch. E30 / E85 compatible. The maximum NOTICE: Stop auger when traveling between recommended ethanol content is 10%. Ariens work areas. recommends using a quality fuel stabilizer in 4. Engage traction drive clutch.

  • Page 14: Stop The Engine

    Check Tire Pressure • understand the Safety section Check Engine Oil • before proceeding. Change Engine Oil ** Your Ariens dealer can provide service and General Lubrication • • adjustments to keep your unit operating at Check Auger Gearcase Oil •...

  • Page 15: Service Parts

    • DO NOT inflate tires above • 414 ml (14 oz) cartridge (1) 00036700 the recommended pressure. Ariens L3 Lube – 237 ml (8 oz) 00068800 • DO NOT inflate tires with a Shear Bolt and Nut 52100100 compressor; use a hand Fuel Stabilizer –...

  • Page 16: Lubricate Unit

    (2.4 – 2.6") from the flat surface of the gearcase cover. IMPORTANT: Ariens recommends using only Ariens L3 synthetic severe duty gear lube (see Service Parts on page 13). Using other lubricants will not automatically void unit warranty, but the warranty will not cover damage caused by using unauthorized lubricants.

  • Page 17: Auger Shaft

    Auger Shaft ADJUSTMENTS 1. Remove shear bolt nuts and bolts. See Figure 17. WARNING: AVOID INJURY. Read and understand the Safety section before proceeding. ADJUST SCRAPER BLADE The auger housing may be damaged if blade wears down too much. 1. Tip unit back onto handlebar, support auger housing and loosen nuts retaining blade.

  • Page 18: Replace Shear Bolts

    If deflector does not follow full range of travel: 1. Position deflector control in the rear-most IMPORTANT: Ariens recommends using only position. Ariens OEM shear bolts when replacing 2. Adjust nuts on chute cable. See shear bolts. Figure 21. See Figure 17.

  • Page 19: Adjust Speed Selector Lever

    ADJUST SPEED SELECTOR ADJUST ATTACHMENT CLUTCH LEVER & BRAKE See Figure 23. WARNING: AVOID INJURY. 1. Disconnect adjustment pivot pin from Improper adjustment could speed selector arm. Save hardware for result in unexpected movement reinstallation. of auger and impeller causing 2.
  • Page 20 • If roller is 12.7 – 22.2 mm (1/2 – 7/8") from frame, no further adjustment is required. • If roller is less than 12.7 mm (1/2") from frame, loosen idler adjustment nut and move idler closer to belt. Tighten adjustment nut and recheck roller clearance.

  • Page 21: Adjust Traction Drive Clutch

    Check Belt Finger Clearance See Figure 28. With attachment clutch engaged, the belt finger located opposite the belt idler must be less than 3.2 mm (1/8") from belts, but must not touch the belts. To adjust belt finger: 1. Remove belt cover. 2.

  • Page 22: Troubleshooting

    (flooded). and reattempt starting. See Start The Engine on page 11. Engine is faulty. See your Ariens dealer or authorized engine manufacturer’s service center. Fuel mixture is too rich. Turn choke control knob to off position. See Choke Control Knob on page 9.
  • Page 23 TROUBLESHOOTING Problem Probable Cause Correction Shear bolts are broken. See Replace Shear bolts on page 16. Attachment clutch / brake is not See Adjust Attachment Clutch & Brake on adjusted correctly. page 17. Impeller is frozen in place. Move unit to a warm place to thaw. Ice or debris is obstructing auger.

  • Page 24: Storage

    2. Tighten all hardware to correct ACCESSORIES specifications. 3. Inspect unit for visible signs of wear or See your Ariens dealer for a complete list of damage. Repair as needed. compatible accessories and attachments for 4. Apply a light layer of oil or anti-rust your unit.

  • Page 25: Specifications

    SPECIFICATIONS Model Number 921045 921046 921047 921048 Deluxe 28 Description Deluxe 24 Deluxe 28 Deluxe 30 Engine Ariens AX Gross Torque* – N•m (lb-ft) 16.6 (12.5) 20.3 (15.0) 254.0 (15.5) 306.0 (16.7) Displacement – cm Maximum RPM – No Load 3600 ±...

  • Page 26: Warranty

    , Sno-Tek ® and Chore Performing Equipment Limited Warranty Warranty Ariens Company (Ariens) warrants to the original purchaser that Ariens, Gravely, Parker, and Countax ® ® brand chore performing equipment (including Sno-Thro and Sno-Tek equipment) purchased on or after 1/1/2015 will be free from defects in material and workmanship for the time period noted in the chart below.
  • Page 27 Register the product immediately at the time of sale. If the dealer does not register the product, the customer must complete the product registration card in the literature package and return it to Ariens Company, or register the unit online at www.ariens.com, www.gravely.com, www.countax.com or www.parkersweeper.com.
  • Page 28 Exclusions – Items Not Covered by This Warranty • Parts that are not genuine Ariens, Gravely, Parker or Countax service parts are not covered by this warranty and may void the warranty. • Damages resulting from the installation or use of any part, accessory, or attachment which is not approved by the Ariens Company for use with product(s) identified herein are not covered by this warranty.
  • Page 30 655 West Ryan Street Brillion, WI 54110 ariensstore.com ariens.custhelp.com parts.ariens.com...

This manual is also suitable for:

921046921047921048Sno-thro deluxe seriesSno-thro deluxe 24Sno-thro deluxe 28 ... Show all

Table of Contents