Program Information, the “ i ” button TV Guide The Radio button Nokia Home Communications operates a policy of continuous development. Therefore we reserve the right to make changes and improvements to any of the products described in this manual without any prior notice.
Never allow liquids, spray or other materials to come into contact with the inside of the Mediamaster. Ÿ Service should be carried out only at a Nokia authorized service center. Ÿ Do not connect or modify cables when the Mediamaster is plugged in.
Power To turn the receiver on/off (standby). INSTALLATION OF THE MEDIAMASTER The box for your Mediamaster should contain the following items: Mediamaster 9660S includes Power cable SCART Cable About the SCART sockets Ÿ The rear panel of the Mediamaster is equipped with 2 SCART sockets.
Connecting the Mediamaster to the satellite dish Installing the satellite dish Ÿ Your satellite dish should be installed with a cable for you to connect to the Mediamaster. If you do not have this cable you will need to buy one from a dealer (tell the dealer you need a coaxial cable and F-connectors).
Connecting to a TV and a Video recorder Refer to your video recorder manual for full instructions. Ÿ Connect one SCART cable between the main SCART socket on the TV and the TV SCART socket on the Mediamaster. Ÿ Connect another SCART cable between the VCR and the VCR SCART socket on the Mediamaster.
Connecting to Hi Fi system Connect an RCA/Cinch stereo cable from the AUDIO L R sockets on the Mediamaster to the LINE, AUX, SPARE or EXTRA input sockets on your Hi Fi system. Preparing the remote control Ÿ Remove the cover on the battery compartment at the bottom of the remote control handset.
About the Smart Card and CA Module. To be able to receive scrambled digital satellite channels you will need a Common Interface CA (Conditional Access) module and a smartcard from a Service Provider. It is possible to use two CA modules. The Service Provider is the programme distributor.
REMOTE CONTROL This section describes how to operate the Mediamaster using the buttons on the remote control. Some of the functions can also be carried out using the buttons on the front panel. To switch the Mediamaster in and out of standby mode. EXIT TV To return to the viewing mode from a menu without storing settings (in menu mode).
BASIC SETTINGS Once you have correctly connected the Mediamaster, you also have to perform some “Basic Settings”. During this procedure, helpful information is displayed at the bottom of the menus. Please note! The OK button always confirms a selection within these menus, and pressing it will take you to the next step in the installation process.
The Welcome Menu To install the Mediamaster properly you have to adjust a few settings. You will always be guided by the information at the bottom of the menus. When you have finished the final part of the setup procedure you can start watching TV channels and listening to radio channels.
Predefined Channel Select one of the predefined channel alternatives Predefined Channel. Adjust Motor Use the RIGHT / LEFT buttons to adjust the motor angle for selected satellite. During you adjust the motor by RIGHT of LEFT buttons, if you can find the AGC and BER level is full or higher level, stop the adjust the motor immediately.
If you download new software from “Nokia Internet pages”, you transfer the software from the computer to the Mediamaster via the serial port IMPORTANT! Updating via satellite may take a while. The front display will indicate the percent left to download.
You can enter a special LNB frequency, which is not presented in the LNB Type list as above. 22KHz Tone Switch: If you have connected to a Dual LNB or two antennas connected to a 22KHz tone switch box, set it to “Enable”...
corresponds to the antenna which you wants to use for the search. Transponder Freq (MHz): Specify the frequency in GHz. using the numbered buttons on your remote control. If you enter the wrong number, erase it with the left arrow button. Polarization: Select polarization;...
Start/Stop Watching TV To start the Mediamaster from stand-by mode, press the “ ” button or one of the numbered buttons on the remote control. It is also possible to start by pressing the button on the front of the Mediamaster.
The display on your Mediamaster and on the TV screen will show the name of the audio channel you are listening to. While in audio mode, you can press the “i” button to get extended information (if transmitted) about the audio programme. Return to TV mode by pressing the TV button again.
To watch TV programmes again, press the TV button or stop the VCR. Please note, that during the recording of a programme, everything shown on the screen will be registered! For example: If you call up a Menu from the Mediamaster on the screen, the menu will be recorded! Subtitling and Teletext.
TV Guide and Radio Guide These guides will give you an overview of programme information from the TV/Radio channels. Step to different channel numbers with the UP/DOWN buttons. If you stop on a highlighted line and press OK, you will exit the menu and enter the highlighted channel.
Add Channels From here you can create your own favorite lists, containing the channels you watch most frequently. You can give each list a specific name in the “Rename List” menu. When a favorite list is selected, you see only those channels defined in the list. You can add channels to your Favorite Lists from the “All TV”, “All Radio”, “Free TV”...
DO NOT FORGET IT! Without it you do not have access to any of the functions where the code is required! If you forget it, you have to contact an Authorized Nokia Service Center to get help. Language Settings From here you can change the language for the menus, main audio language and alternative audio language.
System Settings From here you can adjust settings concerning your TV. TV Screen Format: Select your TV screen format. The 4:3 format is the standard format for most TV screens. Select 16:9 for a wide screen TV. Output Selection: If the teletext function does not work when watching channels from an analogue satellite receiver connected to the Mediamaster, change this setting from “RGB”...
Time Setting You can select the operation mode of the On/Off timer by pressing LEFT/RIGHT button on the remote control. Ÿ Once: The Mediamaster will be switched-on/off for the specified time only once. Ÿ Daily: The Mediamaster will be daily switched-on/off for the specified time.
INSTALLATION SUBMENUS Select this Menu from the line “Installation” in the Main Menu. The submenu will give you the opportunity to change the preferences performed during first time installation. You can also add features that were not included in the first installation.
Reinstall This will start the Installation procedure from the “Welcome Menu”. When you press OK in the “Welcome Menu” again, be aware of the fact, that all previous channels and settings will be erased! To exit the ”Reinstall” menu without erasing any channels, press “Back”.
GLOSSARY OF TERMS ACCESS code Personal Identification Number. A four -digit code stored in the memory. You can change ACCESS code on the “User Preference” Menu. Acquisition Gain Control. Audio system With digital satellite reception, the sound is transmitted in packages and is elected either in a special audio mode or pre-selected by using the installation set-up.
PROBLEM SOLVING Problem Possible causes The display on the Mains lead is not connected. front panel does not light up/is not lit. No sound or picture. The satellite dish is not pointing at the satellite. No signal or weak signal. The LNB is faulty.
TECHNICAL SPECIFICATION Transmission Standards DVB,MPEG2 LNB/Tuner input Connector 2 x F-type (Loop Through) Input frequency 950-2150MHz Max Current 500mA max Supply Voltage 13V/18V DiSEqC RF Impedance 75 ohm Demodulator QPSK Symbol rate 2-45 Msym/s SCPC and MCPC Video decoder MPEG-2 Main Profile @ Main Level Data rates up to 15Mbit/s Video formats...