Download Print this page

Miele F 1813 SF Installation Instructions Manual

Hide thumbs


Quick Links

Installation Instructions

F 1813 SF, F 1913 SF
en - CA
Installation, repair and maintenance work should be performed by
a Miele authorized service technician in accordance with national
and local safety regulations and the provided installation instructions.



  Related Manuals for Miele F 1813 SF

  Summary of Contents for Miele F 1813 SF

  • Page 1: Installation Instructions

    Installation Instructions F 1813 SF, F 1913 SF en - CA Installation, repair and maintenance work should be performed by a Miele authorized service technician in accordance with national and local safety regulations and the provided installation instructions.
  • Page 2: Caring For The Environment

    Caring for the environment Disposing of the packaging Disposal of your old appliance materials Old appliances may contain materials that can be recycled. Please contract The packaging is designed to protect your local recycling authority about the the appliance from damage during possibility of recycling these materials.
  • Page 3: Climate Range

    Installation Installation site Have the appliance installed by a The appliance should be installed in a qualified technician, according to dry, well-ventilated room. the enclosed installation instructions. Do not install the appliance: - outdoors - in an environment with dripping WARNING water This appliance is top-heavy and...
  • Page 4 Installation Important! When there is high humidity a build-up of condensation on the outer surfaces of the appliance can occur.This can cause the surfaces to corrode.To prevent this, it is advisable to install the appliance in a dry and/or an air-conditioned room with sufficient ventilation.Please ensure that doors close and seal properly after...
  • Page 5: Installation Niche

    See "Niche dimensions". hard, rigid material. The side walls of the installation cavity If in doubt, contact Miele. must be plumb. The minimum thickness of the side Furniture/fixtures walls and the top wall must be "...
  • Page 6: Stainless Steel Panels

    The "Merging Kit" is available from Miele. There are many different installation options. You are limited only by the Contact Miele or your dealer for design of the kitchen. specific information about which combinations will work with your The door hinge cannot be appliance.
  • Page 7: Side Panels

    The "Merging Kit" will also be needed. The "Merging Kit" is available from Miele. Installation with partition without using the "Merging Kit" If there is a partition with a thickness of more than 6 "...
  • Page 8 Dimensions Door dimensions (open 115°) F 18X3 SF " (829 mm) " (363 mm) F 19X3 SF " (982 mm) " (428 mm) Miele recommends using the full door opening angle of 115° for this freezer.
  • Page 9: Niche Dimensions

    Dimensions Niche dimensions Niche width (A) F 18X3 SF 30" (762 mm) F 19X3 SF 36" (915 mm)
  • Page 10 Dimensions Power supply and water connection 1. Power supply 2. Water connection F 18X3 SF 15" (381 mm) F 19X3 SF 18" (458 mm) Install a pressure limiting device and water hammer arrester for inlet water pressures exceeding 80 psi.(Refer to Uniform Plumbing Code, Sections 608.2 and 609.10) Never install or operate where inlet water pressure may exceed 120 psi.
  • Page 11: Installing The Appliance

    Installing the appliance Before you begin – Open-ended wrench ½" (SW 13 mm) – Box-end wrench Read these instructions completely and carefully. – " (8 mm) hex nut driver Have the appliance installed by a – Adhesive tape qualified technician, according to –...
  • Page 12: Aligning The Housing Unit

    Installing the appliance Aligning the housing unit Check the installation niche To ensure a safe, trouble-free installation and the best possible cosmetic result, check to be sure that the installation space complies with the installation requirements. ^ Check the base (see "Installation"). ^ Check the dimensions of the cavity.
  • Page 13: Remotevision Module Installation

    Installing the appliance RemoteVision module There are transportation safety installation devices inside the appliance to (optional accessory) protect the shelves and storage compartments until installation is Always disconnect the appliance complete. Do not remove them, or from the power supply when parts may be damaged.
  • Page 14: Preparing The Installation Niche

    In that case, repeat the process. If that does not correct the Keep the appliance door closed problem, contact Miele. until it is securely fastened in the niche. Tipping hazard. Because of the size and weight of the appliance, it is essential to...
  • Page 15 Installing the appliance Mounting Accessories The mounting accessories needed for installing the appliance into the niche are included in the packaging. Several plastic bags are included which are marked alphabetically. The bag needed for each step will be Two anti-tip brackets are marked with its respective letter.
  • Page 16 Installing the appliance In a cabinet without a back wall ^ Now attach the installation niche to the wall. The built-in cabinet must be secured to the wall behind it with several screws. In a cabinet with a back wall ^ screw the cabinet to the wall behind it in several places using suitable mounting brackets.
  • Page 17 Installing the appliance Securing an alternative anti-tip – The beam must cover the appliance by at least 2" (50.8 mm). device ^ Mark the installation height (lower If the anti-tip brackets cannot be attached securely, an alternative edge of the beam) on the rear wall of anti-tip device can be used.
  • Page 18: Sliding The Appliance Into The Installation Niche

    Installing the appliance ^ Plug the appliance into the power Sliding the appliance into the outlet a. installation niche The plug of the appliance should be If a side-by-side installation is easily accessible after installation. desired, connect the two appliances If the plug is not accessible after the together.
  • Page 19: Aligning The Appliance

    Installing the appliance Aligning the appliance – Unscrew the height-adjustable feet until the mark on the base has ^ Align the appliance with the reached the indicated guide surrounding cabinets. dimension 1 1/4" (32 mm). The guide dimension of 1 1/4" (32 mm) is related to a niche height of 84"...
  • Page 20: Attaching The Appliance To The Installation Niche

    Installing the appliance Attaching the appliance to the Attaching the toe-kick cover installation niche The maximum height of the toe-kick cover is 4" from the top of the floor. Do not cover the ventilation slits in the plinth. Risk of damage to the appliance.
  • Page 21 Installing the appliance ^ Insert the foam pieces back into the sides. ^ Position the air separator in the center of the appliance door. ^ Remove the foil from the adhesive strips. ^ Attach the toe-kick cover to the plinth. Mounting the air separator The air separator keeps the supply and exhaust air separate.
  • Page 22 Do not use pipe extenders. Turn off the water supply before In the event that the piping has to be connecting the water lines to the ice replaced only Original Miele Spare cube maker. parts are suitable for use. Contact Miele.
  • Page 23: Preparing The Water Connection

    Plumbing Preparing the water connection For appliances with a hose guide The connection to the household water supply must be installed before the appliance is installed. ^ Turn off the main water valve to prevent damage caused by leaking water. ^ Attach the connecting pipe to the shut-off valve, according to the instructions supplied by the...
  • Page 24: Connecting The Water Supply

    Plumbing ^ Push the union nut and seal onto the Connecting the water supply water pipe. When connecting the water pipe to ^ Push the end of the water pipe into the solenoid valve of the appliance, the appliance connection and screw follow the instructions supplied by on the union nut, 3.
  • Page 25: Electrical Connection

    If there are any questions regarding the electrical connection of this appliance to the power supply, please consult a licensed electrician or call the Miele Technical Service. U1-800-999-1360 V1-800-565-6435...
  • Page 26: Remotevision (Optional Accessory)

    'virtual link' between your following requirements appliance and our monitoring center. If – A wireless router that supports an a fault occurs, Miele's client service IEEE 802.11b/g protocol center will be notified and contact you, ® or another trusted individual identified –...
  • Page 27: Accessing The Remotevision Control Panel

    RemoteVision (optional accessory) ^ Tap the X button until ; appears in Accessing the RemoteVision the display. control panel ^ Touch the access button "p" to confirm. See the table on the following page for a description of each setting in the ^ Touch the access button "p"...
  • Page 28 RemoteVision (optional accessory) MasterCool control panel options for RemoteVision Status indicators Description of function Flashing ; ~ Module booting phase Flashing ; ‡ Not connected to network Flashing ; | Connection to network established, no IP address assigned Solid Connected to network Flashing ;...
  • Page 32 F 1813 SF F 1913 SF en - US, CA M.-Nr. 09 920 840 / 00...

This manual is also suitable for:

F 1913 sf