Page 1
Operating and Installation Instructions Freezer To prevent accidents and appliance damage read these instructions before installation or use. M.-Nr. 10 605 940 en - US, CA...
Page 2
Contents IMPORTANT SAFETY INSTRUCTIONS....... . . 4 Guide to the freezer ..........8 Before use .
Page 4
IMPORTANT SAFETY INSTRUCTIONS Electrical Safety When using the appliance, follow basic safety precautions, including Before installation, make sure that the following: the voltage and frequency listed on the data plate correspond with the Read all instructions before household electrical supply. This data installation and use to prevent must correspond to prevent injury and accidents and machine damage.
Page 5
Installation and repair work should disinfection or other treatment before or be performed by a Miele authorized after the filter is used; the filter alone is service technician. Work by unqualified not an adequate safeguard.
Page 6
IMPORTANT SAFETY INSTRUCTIONS Persons who lack physical, sensory Do not use defrosting sprays or or mental abilities, or experience with de-icers, as they might contain the machine should not use it without substances which could damage the supervision or instruction by a plastic parts or which could cause a responsible person.
Page 7
IMPORTANT SAFETY INSTRUCTIONS Disposal of your old appliance Before disposing of an old appliance, first make the door latch or lock unusable. Take off the door. Leave the shelves in place so that children may not easily climb inside. Consult with your municipal policy on recycling.
Page 8
Guide to the freezer a Door shelves (height adjustable) b Shelves (height adjustable) c Ice cube maker d Ice cube container e Control panel f Main switch to turn the whole appliance On/Off g Freezer baskets h Water filter...
Page 9
Guide to the freezer Control panel a Access button "p" d On/Off sensor button for the ice cube activates the control panel maker b Temperature display e Sensor button for the temperature X colder; Y warmer and door alarm* Allows you to set the desired f Water filter change indicator* temperature in the freezer c On/Off sensor button for the...
Page 10
Before use Before using for the first time Turning the appliance On/Off ^ Open the appliance door. The stainless steel surface of the appliance is protected with a plastic film, which protects it during shipping. Do not remove this protective film until the appliance has been completely installed.
Page 11
Settings Using the settings Additional settings This appliance is operated with the use In the settings mode you can select of touch keys activated by a finger. and change functions. – An available button will appear white. In settings mode, certain settings can be changed.
Page 12
Settings ^ While holding down the X button, Turning the button sound press the access button "p" once. On/Off Keep holding the X button down until If you prefer the buttons to be silent the following appears in the display when touched the button sound can be (approx.
Page 13
Settings Turning off for longer periods of time If the appliance is not going to be used for an extended time (for example, during a vacation) some precautions need to be taken: ^ Shut off the water supply line, (several hours before switching off the appliance) ^ Take all food out of the appliance ^ Turn the appliance off...
Page 14
Temperature and door alarm The appliance is equipped with an Turning the temperature alarm Off alarm system, to ensure that the As soon as the alarm condition is temperature does not rise unnoticed corrected, the alarm signal turns off because of energy loss or an open and the affected zone stops flashing in door.
Page 15
Setting the temperature Setting the temperature Temperature range The temperature can be set within the following range: 7°F to -11°F (-14°C to -24°C). To freeze fresh food and store frozen ^ Touch the access button "p" so it food for an extended period of time, a turns yellow.
Page 16
Setting the temperature ^ While holding down the X button, Temperature unit press the access button "p" once. (Fahrenheit/Celsius) Keep holding the X button down until The temperature can be displayed in the following appears in the display degrees Fahrenheit (°F) or Celsius (°C). (approx.
Page 17
Using the freezer efficiently Freezing food Placing food in the freezer Fresh food should be frozen as quickly Food to be frozen can be placed as possible. This helps maintain the anywhere in the freezer. nutritional value, vitamin content, Load bearing capacity of the baskets: appearance and taste of the food.
Page 18
Using the freezer efficiently Defrosting Cooling drinks quickly Frozen food can be defrosted in To cool drinks quickly, switch on the different ways: SuperCool function, see "SuperCool" for more information. – in a microwave oven, Do not leave bottles in the freezer for –...
Page 19
Using the freezer efficiently Freezing tips – Do not place hot foods or drinks in the freezer. This causes already – The following are examples of foods frozen food to thaw, and increases suitable for freezing: the energy consumption Fresh meat, poultry, game, fish, considerably.
Page 20
SuperCool When the SuperCool function is Switching off SuperCool activated, the appliance is cooled as The SuperCool function automatically cold as possible (to a factory-preset switches off after approx. 52 hours. The temperature). sensor button turns white, and the appliance continues running at normal SuperCool power.
Page 21
Ice cube maker Once the ice cube container is full, the For the automatic ice cube maker to ice cube maker switches off operate, it must be connected to the automatically. household water supply. See "Plumbing". Do not use the ice cube container for rapid cooling of food or drinks.
Page 22
Automatic defrost The freezer defrosts automatically. The moisture generated in the appliance collects in the evaporator. It is automatically defrosted and dissipated by the condenser periodically. This automatic defrosting system enables the freezer to remain permanently ice-free, while ensuring that the food stored in the freezer stays frozen.
Page 23
Adjusting the interior fittings Moving the shelves Replacing a door shelf ^ Start at the top of the slide-rails and The shelves can be adjusted according to the height of the food. slide the shelf down into the desired position. ^ Using both hands, grasp the shelf from underneath and lift slightly so Freezer baskets...
Page 24
Adjusting the interior fittings Ice cube container The ice cube container is set on telescopic tracks, and can be removed for loading, unloading and cleaning. ^ Slide the container forward until resistance is felt. ^ On both sides of the container, pull the latches (see arrow) upward and lift the container out of the freezer.
Page 25
Cleaning and care To better maintain your appliance To reduce the risk of electrical avoid the following: shock, disconnect the appliance – cleaners containing soda, ammonia, from the power supply by shutting thinners, or chlorides off the power main, tripping the circuit breaker or unplugging the –...
Page 26
Cleaning and care Cleaning the interior and The stainless steel doors have a accessories special coating that is soil-resistant. Use a mild solution of warm water and Do not wipe these with a stainless liquid dish soap. Wash all accessories steel conditioner, it will leave visible and drawers by hand.
Page 27
Cleaning and care Additional instructions for stainless Aluminum frames steel appliances: The shelf frames and the door baskets – Appliance doors are made of aluminum. ^ Clean the frames with a mild solution The appliance doors are finished with a high-quality surface coating.
Page 28
Cleaning and care After cleaning Upper lighting ^ Return all shelves and accessories. ^ Shut the appliance door, plug in the appliance and turn it on with the main switch. ^ Turn on the SuperCool function. The freezer section will cool down quickly.
Page 29
Cleaning and care Side lighting ^ Turn the light cover counterclockwise and pull out. Never touch a halogen bulb with bare fingers. When inserting a glass halogen bulb always hold with a soft cloth. ^ Pull the defective light bulb from the socket.
Page 30
– If the ice maker has not been used Additional water filters are available for a prolonged time discard any ice cubes in the freezer, empty the from Miele. container and discard the ice production of the next 24 hours. It is important to change the water –...
Page 31
Water filter Exchanging the water filter Note: Air trapped in the system may cause water and the filter cartridge to eject forcefully. Use caution when removing. ^ Remove the cap from the used filter, ^ Take a new filter cartridge out of the packaging and remove the protective cap.
Page 32
Water filter Using an external water filter If your household water supply already has an external water filter installed, leave the standard water filter (bypass ^ After the filter change the filter cartridge) installed in the appliance. indicator in the display still flashes. The change must be be confirmed in the electronic.
Page 33
T rademark /M odel D esignation R eplacement E lements 9000 077095 9000 077104 Miele 07134220 07134220 M anufacturer : Cuno, Incorporated T he water treatment device ( s ) listed on this certificate have met the testing requirements pursuant to S ection...
Page 34
For estimated costs of replacement elements please contact exceeds 80 psi (552 kPa), you must install a pressure limiting valve. Contact a your local dealer, go to www.miele-shop.com or call Tel. plumbing professional if you are uncertain how to check your water pressure.
Page 35
Lead free certificate This product F 1813 SF (KIMSDF30US) F 1913 SF (KIMSDF36US) is tested and certified by WQA against NSF/ANSI 372 for "lead free" compliance. Miele & Cie. KG Carl-Miele-Straße 29 D-33332 Gütersloh...
Page 36
Check that the fuse has Reset the circuit breaker. not tripped. If the breaker trips again the appliance or the outlet may be defective. Contact Miele or a qualified electrician. The temperature is set Check the display. incorrectly. The temperature Select a warmer See "Selecting the correct...
Page 37
Possible fault Solution Water is flowing out of Close the shut-off valve immediately. the appliance. Check whether the water Contact Miele Technical pipe in the appliance is Service. defective. Check whether the water Contact a plumber. pressure is too low.
Page 38
There has been a power failure. The filter display is red. This is a warning that the Order replacement filters water filter needs to be from Miele. changed soon. The filter display is The water filter needs to See "Exchanging the flashing red.
Page 39
The appliance is not turned Check that the appliance is switched on. The water supply line was Contact Miele. not primed (purged of air) before the appliance was used for the first time. Check if: See "Ice Cube Maker"...
Page 40
Frequently asked questions Problems with the ice maker Issue Possible fault Solution The ice cubes are Other domestic appliances Avoid using such items as a small. that use water are in dishwasher, washing operation. machine or shower at the same time. Check whether the water fil- See "Water filter"...
Page 41
Frequently asked questions Problems with the ice maker Issue Possible fault Solution The ice maker is not Check the water Contact a plumber. producing enough ice pressure. The water or the ice cubes are pressure must be misshapen. between 25 and 80 psi (1.7-5.5 bar).
Page 42
Noises Normal noises What causes them Brrrrr... This noise may get louder for brief periods when the motor kicks on. Blub, blub..A gurgling noise can be heard when the refrigerant circulates through the pipes. Click..Clicking sounds occur whenever the thermostat turns the motor on or off.
Page 43
Miele appliance. Warranty Please note that unless expressly approved in writing by the Miele Ser- For additional information, please refer vice department, Extended Service to your warranty booklet. Contracts offered by other providers for...
Page 45
Installation Instructions Information is subject to change. Please refer to our website to obtain the most current product specification, technical & warranty information. To prevent accidents and machine damage read these instructions before installation or use.
Page 46
Caring for the environment Disposing of the packaging Disposal of your old appliance materials Old appliances may contain materials that can be recycled. Please contact The packaging is designed to protect your local recycling authority about the the appliance from damage during possibility of recycling these materials.
Page 47
Installation Installation site Have the appliance installed by a The appliance should be installed in a qualified technician, according to dry, well-ventilated room. the enclosed installation instructions. Do not install the appliance: - outdoors - in an environment with dripping WARNING water This appliance is top-heavy and...
Page 48
Installation Important! When there is high humidity a build-up of condensation on the outer surfaces of the appliance can occur.This can cause the surfaces to corrode.To prevent this, it is advisable to install the appliance in a dry and/or an air-conditioned room with sufficient ventilation.Please ensure that doors close and seal properly after...
Page 49
See "Niche dimensions". hard, rigid material. The side walls of the installation cavity If in doubt, contact Miele. must be plumb. The minimum thickness of the side Furniture/fixtures walls and the top wall must be "...
Page 50
The "Merging Kit" is available from Miele. There are many different installation options. You are limited only by the Contact Miele or your dealer for design of the kitchen. specific information about which combinations will work with your The door hinge cannot be appliance.
Page 51
The "Merging Kit" will also be needed. The "Merging Kit" is available from Miele.
Page 52
Dimensions Door dimensions (open 115°) F 1803 SF, F 1813 SF ° �- - Miele recommends using the full door opening angle of 115° for this freezer.
Page 53
Dimensions F 1903 SF, F 1913 SF 16 7/8" (428 ° .,,,,. ,, Miele recommends using the full door opening angle of 115° for this freezer.
Page 54
W*: The position of the 1/4" water supply (not included) should not be higher than 2" from the floor. Please notice: Miele recommends to place the electrical outlet next to the appliance. The electrical outlet must be easily accessible in case of an emergency!
Page 55
W*: The position of the 1/4" water supply (not included) should not be higher than 2" from the floor. Please notice: Miele recommends to place the electrical outlet next to the appliance. The electrical outlet must be easily accessible in case of an emergency!
Page 56
Installing the appliance Before you begin – Open-ended wrench ½" (SW 13 mm) – Box-end wrench Read these instructions completely and carefully. – " (8 mm) hex nut driver Have the appliance installed by a – Adhesive tape qualified technician, according to –...
Page 57
Installing the appliance Aligning the housing unit Check the installation niche To ensure a safe, trouble-free installation and the best possible cosmetic result, check to be sure that the installation space complies with the installation requirements. ^ Check the base (see "Installation"). ^ Check the dimensions of the cavity.
Page 58
Installing the appliance RemoteVision module There are transportation safety installation devices inside the appliance to (optional accessory) protect the shelves and storage compartments until installation is Always disconnect the appliance complete. Do not remove them, or from the power supply when parts may be damaged.
Page 59
In that case, repeat the process. If that does not correct the Keep the appliance door closed problem, contact Miele. until it is securely fastened in the niche. Tipping hazard. Because of the size and weight of the appliance, it is essential to...
Page 60
Installing the appliance Mounting Accessories Risk of tipping The mounting accessories needed for The installation niche must be installing the appliance into the niche securely attached to the wall behind are included in the packaging. Several it. This is the only way the plastic bags are included which are appliance, which is later secured in marked alphabetically.
Page 61
Installing the appliance In a cabinet without a back wall ^ Now attach the installation niche to the wall. The built-in cabinet must be secured to the wall behind it with several screws. In a cabinet with a back wall ^ screw the cabinet to the wall behind it in several places using suitable mounting brackets.
Page 62
Installing the appliance Securing an alternative anti-tip – The beam must cover the appliance by at least 2" (50.8 mm). device ^ Mark the installation height (lower If the anti-tip brackets cannot be attached securely, an alternative edge of the beam) on the rear wall of anti-tip device can be used.
Page 63
Installing the appliance ^ Plug the appliance into the power Sliding the appliance into the outlet a. installation niche The plug of the appliance should be If a side-by-side installation is easily accessible after installation. desired, connect the two appliances If the plug is not accessible after the together.
Page 64
Installing the appliance Aligning the appliance – Unscrew the height-adjustable feet until the mark on the base has ^ Align the appliance with the reached the indicated guide surrounding cabinets. dimension 1 1/4" (32 mm). The guide dimension of 1 1/4" (32 mm) is related to a niche height of 84"...
Page 65
Installing the appliance Attaching the appliance to the Attaching the toe-kick cover installation niche The maximum height of the toe-kick cover is 4" from the top of the floor. Do not cover the ventilation slits in the plinth. Risk of damage to the appliance.
Page 66
Installing the appliance ^ Insert the foam pieces back into the sides. ^ Position the air separator in the center of the appliance door. ^ Remove the foil from the adhesive strips. ^ Attach the toe-kick cover to the plinth. Mounting the air separator The air separator keeps the supply and exhaust air separate.
Page 67
– The appliance is only suitable for In the event that the piping has to be connection to the cold water supply. replaced only Original Miele Spare parts are suitable for use. Contact – The water pressure must be between Miele.
Page 68
Plumbing Preparing the water connection For appliances with a hose guide The connection to the household water supply must be installed before the appliance is installed. ^ Turn off the main water valve to prevent damage caused by leaking water. ^ Attach the connecting pipe to the shut-off valve, according to the instructions supplied by the...
Page 69
Plumbing ^ Push the union nut and seal onto the Connecting the water supply water pipe. When connecting the water pipe to ^ Push the end of the water pipe into the solenoid valve of the appliance, the appliance connection and screw follow the instructions supplied by on the union nut, 3.
Page 70
If there are any questions regarding the electrical connection of this appliance to the power supply, please consult a licensed electrician or call the Miele Technical Service. U1-800-999-1360 V1-800-565-6435...
Page 71
'virtual link' between your following requirements appliance and our monitoring center. If – A wireless router that supports an a fault occurs, Miele's client service IEEE 802.11b/g protocol center will be notified and contact you, ® or another trusted individual identified –...
Page 72
RemoteVision (optional accessory) ^ Tap the X button until ; appears in Accessing the RemoteVision the display. control panel ^ Touch the access button "p" to confirm. See the table on the following page for a description of each setting in the ^ Touch the access button "p"...
Page 73
RemoteVision (optional accessory) MasterCool control panel options for RemoteVision Status indicators Description of function Flashing ; ~ Module booting phase Flashing ; ‡ Not connected to network Flashing ; | Connection to network established, no IP address assigned Solid Connected to network Flashing ;...
Page 76
F 1813 SF F 1913 SF M.-Nr. 10 605 940 / 01 en - US, CA...
Need help?
Do you have a question about the F 1913 SF and is the answer not in the manual?
Questions and answers