Unpacking - Dometic miniCool DS 200 Operating Instructions Manual

1. Unpacking

After removal from the cardboard packaging, make
sure the appliance is not damaged. If you find damage
to the appliance resulting from transport, report it
immediately to the transportation firm.
2. View of the appliance
2. Door
3. Evaporator
4. Thermostat knob
5. Cooling unit cover
6. Interior light
IN CASE IF YOUR REFRIGERATOR IS EQUIPPED WITH LOCK, DOMETIC ZRT DO NOT ACCEPT
LIABILITY FOR LOSS OR DAMAGE OF KEYS. HOWEVER A COMPLETE LOCK CAN BE SUPPLIED.
3. Cleaning
Clean the refrigerator thoroughly at intervals, as
necessary. Remove the shelves; these parts, as
well as the cabinet interior and the door should be
washed with a warm solution of sodium bi-carbonate.
Finally wipe over with a cloth rinsed in warm water
only, and dry with a clean cloth. Do not wash any
plastic parts in water that is more than hand warm, and
do not expose them to dry heat. The outside of the
cabinet should be wiped down regularly with a clean,
damp cloth.
NEVER USE STRONG CHEMICALS OR ABRASIVE
CLEANING MATERIALS ON ANY PART OF THE
CABINET.
4. Positioning the appliance
When first using this refrigerator please consider the
following points:
ENSURE REFRIGERATOR IS LEVEL
THE PIPEWORK AT THE BACK GETS HOT IN USE
THE REFRIGERATOR HAS NO 'MOTOR' AND IS
THEREFORE VIRTUALLY SILENT
ALLOW AT LEAST 3 HRS. FOR SIGNS OF COOLING
During the refrigeration process, the appliance
gives off heat from the condenser (under the
upper part of the rear cover) into the surrounding air.
The more ventilated the condenser is, the more
effective the refrigeration will be.
The other condition for satisfactory operation is that
the appliance is levelled. This could be checked by
placing a glass of water on top of the appliance.
It is important that the appliance is not directly
exposed to radiated heat (sunlight, radiator, near an
oven, etc.).
Please do not place the refrigerator onto thick
carpet!
(fig. 2.)
1. Door lock (if available)
All model are available in freestanding and built-in
version. BI in the modelname refers for the built-in
version and FS for the freestanding version. Please
check your product version (figure 1.) and follow
the relevant instructions about the installation and
operation.
7. Shelves
8. Footframe
9. Air-sensor
10. Door racks
11. Evaporator-sensor
4.1. Installation instructions
All four sizes of the miniCool family are available in
built-in and freestanding version.
4.1.1. Built-in versions
This version is intended for built in purposes. Built
in models do not have foot frames, cooling unit
covers compared to the freestanding versions
(figure 1).
The miniCool can be screwed to the furniture using
the fittings at the bottom. Drive in the screws (figure
3).
4.1.2. Freestanding versions
These versions are intended for freestanding use.
Cooling unit covers protect the hot parts of the
cooling units. Foot frames with grilles ensure
sufficient ventilation.
These models can be also build in into the
furnitures with sliding hinges or simply be pushed
into a given space. In this case please take into the
consideration items listed below.
IMPORTANT
Please follow the installation details below
carefully. Guarantee is valid for products
installed as described only.
1. The refrigerator must be level both directions
2. There should be 20 mm clearance to the wall
3. Ventilation must be provided as shown in
alternatives A, B, C or D (fig 4-5)
1. Air in
2. Air out
3. Ventilation grille
4. Only the entire cooling unit must project into
the duct as shown
5. Air passing through the duct must not be
preheated by any source of heat
GB
(fig. 3.)
(fig. 4-5.)
7