Denna bok kan finnas tillgänglig på ditt språk. Kontakta din återförsäljare Svenska eller gå till: www.operatorsguide.brp.com. Know Before you Go Congratulations on your purchase of a new Sea-Doo ® personal water- To learn how to reduce the risk for you craft (PWC). It is backed by the BRP...
FOREWORD The informations contained in this doc- WARNING ument are correct at the time of publi- Get familiar with this PWC; it may cation. However, BRP maintains a pol- exceed the performance of other icy of continuous improvement of its PWCs you have ridden.
CO poisoning, serious health prob- craft illegal for use on water. lems and death. See your authorized Sea-Doo dealer for available accessories for your wa- Avoid Gasoline Fires and tercraft. Other Hazards Gasoline is extremely flammable and highly explosive.
SPECIAL SAFETY MESSAGES Reminders Regarding Safe When braking, riders must brace them- selves against the deceleration force Operation to prevent from moving forward on the The performance of this watercraft watercraft and losing balance. may significantly exceed that of other When operating an iBR equipped wa- watercraft you may have operated.
Page 12
SPECIAL SAFETY MESSAGES Do not store any objects in areas that Keep the tether cord attached to the are not designed specifically for stor- operator's PFD or wrist (wrist strap age. required) at all times and keep it free from snagging on the handlebars to Riding with passenger(s), pulling help ensure the engine stops should...
Page 13
The operator and passenger(s) should Read and understand all safety labels be properly seated and have a firm grip on the Sea-Doo PWC, the Operator's on a handhold before starting the wa- Guide, all other safety documents, and tercraft, and at all times when the wa-...
Page 14
SPECIAL SAFETY MESSAGES should be instructed to use the hand- On a PWC, never place your feet and holds provided, or to hold on to the legs in the water to aid turning. waist of the person in front of them. Operation by Minors Each passenger must be able to simul- taneously place both feet firmly flat...
SPECIAL SAFETY MESSAGES Water Sports (Towing with – When pulling a tube, skier, or a wake boarder, do not make tight sharp the Watercraft) turns or use the braking system unless absolutely necessary. Re- WARNING member that although this PWC is Avoid personal injury! Your PWC manoeuvrable and has stopping ca- is not designed for and should not...
SPECIAL SAFETY MESSAGES – Approach a person in the water from straps can become entangled in mov- the lee side (opposite the direction ing parts resulting in serious injury or of the wind). Turn off the motor be- drowning. In shallow water, shells, fore coming close to the person.
SPECIAL SAFETY MESSAGES Some points to remember about hy- pothermia protection: – While afloat in the water, do not at- tempt to swim unless it is to reach a nearby watercraft, fellow sur- vivor, or a floating object onto which you can lean or climb.
ACTIVE TECHNOLOGIES (iCONTROL) Introduction The iTC allows the following operating modes: NOTE: Some functions or features de- – Touring mode scribed in this section may not apply to every PWC model, or may be available – Sport mode as an option. –...
ACTIVE TECHNOLOGIES (iCONTROL) unlike an automotive type cruise con- Learning Key and Rental Key Modes trol which maintains a constant speed The Sea-Doo learning key limits the while throttle pedal is released. speed of the watercraft therefore en- As you proceed under a constant cruis-...
Page 20
ACTIVE TECHNOLOGIES (iCONTROL) Under ideal conditions, experienced operators were consistently able to reduce the stopping distance of a wa- tercraft equipped with an iBR system by approximately 33%, from an initial speed of 80 km/h (50 MPH). Limitations Even when equipped with an iBR sys- tem, watercraft do not have the ability of land based vehicles.
SAFETY EQUIPMENT Required Safety Recommended Protective Gear Equipment The operator and passenger(s) of PWCs must wear protective gear, in- The operator and the passenger(s) cluding: must wear an approved Personal Flota- tion Device (PDF) that is suitable for – A wet suit bottom, or thick tightly PWC use.
Page 22
SAFETY EQUIPMENT A PFD provides buoyancy to help keep ability of quick rescue such as in areas the head and face above the water, and where other people are commonly in- to help maintain a satisfactory body po- volved in water activities. sition while in the water.
SAFETY EQUIPMENT Weighing the Risks vs Benefits In order to decide whether or not you should wear a helmet, it is best to con- sider the particular environment you will be riding in, as well as other fac- tors such as personal experience. Will there be a lot of traffic on the water? What is your riding style? The Bottom Line...
PRACTICE EXERCISES It is always a good idea to practice and Watercraft Equipped with iBR get familiar with all controls, functions Practice stopping the watercraft in and handling characteristics of your a straight line at various speeds and watercraft before venturing on the wa- braking force.
PRACTICE EXERCISES Slow Speed Mode, Ski Mode and Cruise Mode If your watercraft has any of these modes, it is also important to under- stand their operation and to become familiar with these features prior to us- ing them on a ride with other people. WARNING The ski and the cruise modes are not an automatic pilot;...
NAVIGATION RULES Operating Rules Operating a watercraft can be com- pared with driving on unmarked high- ways and roads. To prevent collisions or avoid other boaters, a system of op- erating rules must be followed. It’s not only common sense... it’s the law! smo2012-003-200 Generally keep to your right and safely TYPICAL...
Page 27
NAVIGATION RULES buoy, or to which channel you can con- When operating an iBR equipped wa- tinue. They may also indicate whether tercraft, be aware that other boats fol- you are entering a restricted or con- lowing or operating in close proximity trolled area such as a no wake or low may not be able to stop as quickly.
FUELING Fueling Procedure WARNING Fuel tank may be pressurized, fuel WARNING vapors may be released while re- moving the fuel tank cap. Fuel is flammable and explosive under certain conditions. Always work in a well ventilated area. Do 8. Insert the gas pump spout into the not smoke or allow open flames or filler neck and fill up the fuel tank.
Page 29
FUELING NOTICE Never experiment with other fuels. Never use fuel contain- ing more than 10% ethanol. The use of a non-recommended fuel can result in decreased engine perfor- mance and damage to critical parts in the fuel system and engine. Inside North America MINIMUM OCTANE RATING ENGINE...
A Sea-Doo cover can protect the wa- WARNING tercraft, particularly when driving on dirt roads, to prevent dirt entry through Never tip this watercraft on end for the air inlet openings.
(2-UP) or bystanders. The labels illustrated on the following pages are on your watercraft. If missing or damaged, they can be replaced free of charge. See an authorized Sea-Doo dealer. Please read the following labels carefully before operating this watercraft.
Page 32
IMPORTANT ON-PRODUCT LABELS smo2011-003-003_a WATERCRAFT SAFETY LABEL LOCATION - WAKE MODEL 219903451B LABEL 1 - MAIN WARNING LH (GTS MODELS ONLY) _______ ________ SAFETY INFORMATION...
Page 33
IMPORTANT ON-PRODUCT LABELS 219903447B LABEL 1 - MAIN WARNING LH (GTI SERIES AND WAKE MODELS) 219903448B LABEL 2 - MAIN WARNING RH ________ ________ SAFETY INFORMATION...
The pre-ride inspection can help you monitor wear and deterioration before they become a problem. Correct any problems that you discover to reduce the risk of a breakdown or crash. See an authorized Sea-Doo dealer as necessary. CONTROLS Before performing the pre-ride inspection, read and understand the section.
Page 39
Clean as necessary. If any obstruction smo2009-002-135_a cannot be removed, refer to an autho- TYPICAL - BILGE DRAIN PLUG LOCATIONS 1. Bilge drain plugs rized Sea-Doo dealer for servicing. 2. Tighten 3. Untighten WARNING Ensure bilge drain plugs are prop- erly secured prior to launching the watercraft in water.
Page 40
Refer to same direction as the handlebar (e.g.: an authorized Sea-Doo dealer be- when handlebar is turned to the left, fore use. the nozzle opening must point towards the LH side of watercraft).
START/STOP button does not stop the engine, do not use the WAKE Model watercraft. See your authorized Make sure ski/wakeboard post is fully Sea-Doo dealer. extended and locked before use. What to Do After Completely retract and lock when not used.
Page 42
PRE-RIDE INSPECTION Information Center (Gauge) Also test the VTS preset trim positions by double clicking the VTS UP/DOWN 1. Press START/STOP button and in- button (as applicable to model). stall the tether cord cap on the en- OPERATING INSTRUCTIONS gine cut-off switch. Refer to subsection for detailed instructions.
CONTROLS 1) Handlebar Waking Up the Electrical System The handlebar controls the direction of Press the START/STOP button once the watercraft. During forward opera- without installing the tether cord on tion, turning the handlebar to the right the engine cut-off switch. steers the watercraft to the right and This will power up the electrical sys- inversely.
Page 48
CONTROLS To have a key programmed to your watercraft, see your authorized BRP Sea-Doo dealer. D.E.S.S. Key Recognition Two short beeps indicate the system is ready to allow engine starting. Oth- TROUBLESHOOT- erwise, refer to the section. D.E.S.S. Key Types...
– LEARNING KEY The throttle lever is spring loaded and – RENTAL KEY. should return to rest position (idle) when not pressed. SEA-DOO learning rental key, limits the speed of the 5) iBR Lever (intelligent watercraft and the engine torque,...
CONTROLS OPERATING INSTRUCTIONS At speeds above 8 km/h (5 MPH), Refer to pulling the iBR lever in will engage the subsection for detailed instructions. brake. 7) UP/DOWN Buttons When the iBR lever is released after braking or reverse operation, neutral is All Models Except GTS engaged.
CONTROLS Press the VTS control button (up/down arrow) to adjust the riding attitude of the watercraft. OPERATING INSTRUCTIONS Refer to subsection for details. 10) Sport Button The Sport button is located on the LH handlebar. sdd2009-001-024_g TYPICAL 1. Cruise button It is used to activate or deactivate CRUISE mode or to engage SLOW SPEED MODE.
INFORMATION CENTER (GAUGE) (GTS) WARNING Do not adjust the display while riding, you could lose control. smo2011-003-024_a TYPICAL - GTS MODELS 1. Multifunction gauge Multifunction Gauge – Display the engine RPM Description – Display fault messages. NOTE: If a fault occurs, it will period- ically scroll the applicable fault mes- sage in the display and revert to the RPM indication depending on the...
Page 53
Fuel tank symbol nance is due. When this indicator comes on, bring Audible advisory your watercraft to your authorized (one long beep) Sea-Doo dealer to have it serviced and Periodically Scrolling LOW to have the maintenance reminder in- FUEL advisory dicator reset.
MPH. It is also capable of displaying messages in various languages. To have your gauge set up to your pre- ferred unit of measurement and avail- able language, see your authorized Sea-Doo dealer. ______________...
INFORMATION CENTER (GAUGES) (GTI/GTR/WAKE) WARNING Do not adjust the display while riding, you could lose control. smo2011-003-023_a TYPICAL - GTI AND GTI SE MODELS 1. Multifunction gauge smo2012-001-007_a TYPICAL - GTI LIMITED, GTR AND WAKE MODELS 1. Multifunction gauge 2. Analog speedometer 3.
INFORMATION CENTER (GAUGES) (GTI/GTR/WAKE) Multifunction Gauge Features GTI SE WAKE LIMITED Touring mode indicator Sport mode indicator Fuel level indication Hour meter display Water depth indication ECO mode indicator CRUISE mode indicator iBR position indicator SKI mode indicator VTS position indication X = Indicates a standard feature Opt = Indicates a feature available as an option Multifunction Gauge...
Page 57
INFORMATION CENTER (GAUGES) (GTI/GTR/WAKE) NUMERICAL DISPLAY 1. Numerical display indication 2. Unit of measurement of indication AVAILABLE INDICATIONS IN NUMERICAL DISPLAY GTI SE GTI Limited WAKE Watercraft speed Indication by default Engine RPM Engine temperature Clock N.A. Learning key settings CRUISE SPEED setting SLOW SPEED MODE setting VTS preset...
INFORMATION CENTER (GAUGES) (GTI/GTR/WAKE) 3) Touring Mode Indicator When the TOURING mode indicator is ON, the default TOURING mode of op- eration is active. FUEL LEVEL INDICATION When the fuel tank is full, 8 segments (bars) of the indicator are turned on. The top segment is not used.
Page 59
When this indicator comes on, bring WATER DEPTH DISPLAY your watercraft to your authorized Sea-Doo dealer to have it serviced and NOTE: The water depth indication is to have the maintenance reminder in- only available when a depth sounder is dicator reset.
INFORMATION CENTER (GAUGES) (GTI/GTR/WAKE) iBR FAULT INDICATOR CRUISE MODE INDICATOR TROUBLESHOOTING OPERATING MODES Refer to sub- Refer to subsec- section for details. tion for detailed instructions. 12) ECO Indicator 14) iBR Position Indicator The ECO indicator and a smile in the Provides an indication of the iBR gate fuel tank symbol comes ON when position.
INFORMATION CENTER (GAUGES) (GTI/GTR/WAKE) 16) VTS Position Indication The VTS position indication provides an indication of the pump nozzle position. A single segment of a bar gauge type indicator is turned on to indicate the rel- ative position of the watercraft bow. FUNCTION SUBMENU DISPLAYED IN SEQUENCE WHEN MODE BUTTON PRESSED REPEATEDLY...
Page 62
INFORMATION CENTER (GAUGES) (GTI/GTR/WAKE) NOTE: The compass indication is only NOTE: The timer starts immediately available above 5 km/h (3 MPH). when pressing the SET button. 4. To record each lap time, press the WARNING SET button at the start of each lap. Use the compass as a guide only.
Page 63
INFORMATION CENTER (GAUGES) (GTI/GTR/WAKE) When the LOW FUEL indications come on in the multifunction gauge, the "TIME TO EMPTY" and "DISTANCE TO EMPTY" functions will indicate "0" (zero) if they are the selected indica- tion. To display the watercraft fuel con- sumption, carry out the following: 1.
INFORMATION CENTER (GAUGES) (GTI/GTR/WAKE) NOTE: The fuel consumption value selected will be displayed in the nu- merical display. Double click the SET button to reset the average fuel con- sumption indication. The display will momentarily indicate zero (0). VTS Mode The VTS MODE function is used to manually set the VTS or change VTS MESSAGE DISPLAYED...
INFORMATION CENTER (GAUGES) (GTI/GTR/WAKE) Resetting Numerical Display Indication The following numerical display indica- tions can be reset when selected: – Average fuel consumption – Top speed – Average speed – Top RPM FUNCTION SELECTED - CLOCK – Average RPM. To reset the indication. double click the 1.
INFORMATION CENTER (GAUGES) (GTI/GTR/WAKE) To change the units of measurement or to change the language displayed in the multifunction gauge, see your authorized Sea-Doo dealer. Analog Speedometer Description The speedometer, located in the LH side of the information center, pro-...
EQUIPMENT NOTE: Illustrations may not be accurate for every model and are only provided as a visual guide. smo2011-003-003_b TYPICAL - WAKE MODEL ILLUSTRATED 1) Glove Box A small, storage compartment for per- sonal articles. Pull up on cover latch to open glove box.
EQUIPMENT smo2011-003-025_a TYPICAL smo2009-002-129_a 1. Front storage compartment cover TYPICAL - SEAT LATCH 2. Latch lever 1. Seat latch handle 2. Latch pin 3. Pin insertion hole WARNING Never carry any loose, heavy, To install the seat, insert the forward sharp, or breakable objects in the end of the seat in it's retainer.
EQUIPMENT a handhold for the skier/wakeboarder spotter or boarding the watercraft from the water. NOTICE Never use the molded grab handle to tow anything or to lift the watercraft. smo2009-002-133 BOARDING STEP HELD DOWN FOR BOARDING FROM WATER NOTICE – Never use the step for boarding a watercraft that is out of water.
EQUIPMENT Rear Eyelets smo2011-003-014_a smo2009-002-132_b 1. Boarding platform TYPICAL 2. Spotter foot rests (each side) 1. Rear eyelets 7) Front and Rear Eyelets All Models Except WAKE Eyelets can be used for mooring, tow- ing a water skier, wakeboarder or tu- ber, and as tie-down points when trai- lering your watercraft.
EQUIPMENT NOTICE Ensure drain plugs are properly secured prior to launching the watercraft in water. 9) Ski/Wakeboard Post WAKE Model Pull up on the knob to extend the post. Ensure both sections of post are fully extended and properly locked before smo2011-003-017_a attaching ski or wakeboard rope.
Page 72
EQUIPMENT 2. Rotate the rack upwards and push the top of the rack inboard until the handle locks into the top retaining bracket. WARNING If rack is not properly secured on the watercraft, it could become loose and detach unexpectedly, creating a risk of injury to people nearby.
Page 73
EQUIPMENT To remove the wakeboard rack, de- WARNING press the lever at the top of the rack If the wakeboard is not properly se- and remove it from its retaining brack- cured on the rack, it could become ets. loose and detach unexpectedly, creating a risk of injury to people nearby.
BREAK-IN PERIOD Operation During Break-In Period A break-in period of 10 operating hours is required before running the water- craft at sustained full throttle. During this period, maximum throttle should not exceed 1/2 to 3/4 opening. However, brief full acceleration and speed variations contribute to a good break-in.
Should any control or instruction not be fully understood, refer to an authorized Sea-Doo dealer. Boarding from Water Boarding the Watercraft Ensure there is at least 90 cm (3 ft) of...
Page 76
OPERATING INSTRUCTIONS 2. With the other hand on the boarding Using the other hand, take hold of the platform, lift your body until you can edge of the boarding platform, then lay one knee on the boarding plat- pull yourself up so that you can knee form.
Page 77
OPERATING INSTRUCTIONS smo2009-002-146 smo2009-002-144 The passenger then climbs onto the Take hold of the seat strap to help main- watercraft while the operator main- tain your balance and step forward tains balance by sitting as close as pos- onto the footboards on either side of sible to the console.
OPERATING INSTRUCTIONS 6. Release engine START/STOP but- ton immediately after engine is started. WARNING The tether cord clip should always be attached to the operators per- sonal flotation device when start- ing or operating the watercraft. smo2009-002-150 How to Start Engine NOTICE Do not hold START/STOP WARNING...
OPERATING INSTRUCTIONS How to Steer the The watercraft behaves differently with a passenger and requires greater Watercraft skill. The passenger(s) should always grip the seat strap, the molded grab handle, or the waist of the person ahead of them. Reduce speed and avoid sharp turns.
OPERATING INSTRUCTIONS How to Engage Neutral NOTE: Press the UP/DOWN button repeatedly until proper adjustment of iBR Equipped Models Only the neutral position is attained and the watercraft stops moving. WARNING How to Engage Forward The drive shaft and impeller are always turning when the engine is iBR Equipped Models Only running, even in neutral position.
Page 81
OPERATING INSTRUCTIONS When operating in reverse, turn the handlebar in the opposite direction that you want to move the rear of the watercraft. For example, to steer the rear of the watercraft to port (left), turn the han- dlebar to starboard (right). smo2009-002-202_a TYPICAL - iBR LEVER 1.
OPERATING INSTRUCTIONS How to Engage and Use When iBR lever is applied, the throttle lever command is overridden and en- Braking gine throttle control is now dependant iBR Equipped Models Only on the iBR lever position. Braking can thus be modulated by using only the WARNING iBR lever.
OPERATING INSTRUCTIONS If the throttle lever is still pulled in CAUTION As the watercraft when releasing the iBR lever, the wa- slows to a stop while braking in a tercraft will accelerate forward after a turn, the wake created by the water- short delay.
Page 84
OPERATING INSTRUCTIONS VTS POSITION INDICATION The VTS system allows for manually adjusting the trim position of the nozzle, or se- lecting two preset trim positions and recording or changing preset trim positions on certain models. VTS Trimming Methods AVAILABLE VTS TRIMMING METHODS GTI SE GTI Limited WAKE...
Page 85
OPERATING INSTRUCTIONS Trimming the VTS Using the VTS Using Preset Trim Positions Button Two preset trim positions can be se- Five trim positions are available. lected. With the watercraft operating in for- To select the highest trim position ward position, proceed as follows: recorded, double-click on the VTS UP button (bow up).
Page 86
OPERATING INSTRUCTIONS 3. On the RH handlebar, press the MODE button repeatedly until VTS MODE is displayed. FUNCTION SELECTED - PRESET 1 1. PRESET 1 message 2. VTS setting number 3. VTS position indicator at setting 1 sdd2009-001-024_b (bow down) 1.
OPERATING INSTRUCTIONS WARNING When crossing wakes, slow down. Operator and passenger(s) should brace themselves and adopt a semi-standing position to help absorb the bumps. Do not jump waves or wakes. Stopping/Docking FUNCTION SELECTED - VTS When the throttle is released, the wa- tercraft is slowed by water drag against 1.
Page 88
OPERATING INSTRUCTIONS iBR Equipped Models Only WARNING The iBR system can also be used for Directional control is reduced slowing down or for stopping the when the throttle is released watercraft more quickly, and for in- and/or when engine is off. Steer- creasing maneuverability especially ing direction is reversed when op- when docking.
OPERATING MODES WAKE LIMITED Touring mode Sport mode ECO mode Cruise mode N.A. Slow speed mode N.A. N.A. Ski mode Learning key modes X = Indicates a standard feature Opt = Indicates a feature available as an option N.A. = Not Applicable Touring Mode By default, the watercraft is in TOUR- ING mode of operation when first...
Page 90
OPERATING MODES smo2012-002-009_a MESSAGE DISPLAYED TYPICAL SPORT MODE ACTIVATED 1. Sport button NOTE: The following important mes- NOTE: After a few seconds, the gauge sage will scroll across the multifunc- will revert to its normal display. tion display: 3. Ensure the SPORT mode indicator is turned on.
OPERATING MODES The following message will be dis- played on the multifunction display: MESSAGE DISPLAYED SPORT MODE DEACTIVATED MESSAGE DISPLAYED NOTE: After a few seconds, the gauge ECO MODE will revert to its normal display. 2. Ensure the TOURING mode indica- The ECO mode indicator will also be ac- tor is on.
OPERATING MODES Cruise Mode To activate and preset CRUISE MODE at idle speed, carry out the following: Cruise mode is a function of iTC (in- telligent Throttle Control) system that 1. Tap the throttle lever to move the allows the operator to set the desired iBR to the forward position.
Page 93
OPERATING MODES A beep indicating that you are now in cruise mode will sound, and a CRUISE indicator will come on in the multifunc- tion gauge. sdd2009-001-024_i 1. UP button 2. DOWN button The following will be displayed in the multifunction gauge.
OPERATING MODES CRUISE MODE INDICATOR FUNCTION SELECTED - CRUISE MODE Changing Set Cruise Speed 1. CRUISE MODE _ SPEED To increase or decrease the set cruise ADJUSTING speed: 2. Cruise speed set point indication 1. Hold the throttle lever all the way in to the handlebar.
Page 95
OPERATING MODES The operator can select an idle speed set point (slow speed) be- tween 1 and 5 (1.6 km/h to 11 km/h (1 MPH to 7 MPH)). If you accelerate above approximately 14 km/h (9 MPH), Slow Speed Mode will be deactivated and the engine will return to its normal idle RPM when the throttle is released.
OPERATING MODES sdd2009-001-024_i MESSAGE DISPLAYED 1. UP button to increase speed SLOW SPEED MODE ACTIVE 2. DOWN button to decrease speed While the UP/DOWN is being pressed Deactivating Slow Speed Mode to change the slow speed set point, the following will appear in the multi- Slow speed mode can be deactivated function gauge.
OPERATING MODES RAMP 1 provides: – Slowest launch (smoothest) – Slowest acceleration rate – Slowest TARGET SPEED range. RAMP 5 provides: – Quickest launch – Quickest acceleration rate – Highest TARGET SPEED range. sdd2009-001-024_e TYPICAL TARGET SPEED Function 1. MODE button The TARGET SPEED function limits the maximum towing speed.
Page 98
OPERATING MODES MESSAGE DISPLAYED FIRST SETTING AVAILABLE - RAMP SKI MODE_PRESS_SET_TO START OR 1. RAMP message MODE TO EXIT 2. Ramp setting NOTE: A BEEP will be heard every 5 4. To change the RAMP setting, press seconds as a SKI MODE engaged re- the UP/DOWN button until the de- minder.
OPERATING MODES 9. To launch the PWC in ski mode, pull To end a ski run and completely deac- in and hold the throttle lever all the tivate ski mode, release the throttle to way to the handlebar grip. The PWC idle, then press the MODE button.
Page 100
OPERATING MODES 6. Press the SET button once to save the setting, twice to exit the func- tion, or simply wait for the function to time-out. The change in key set- ting will automatically be saved. NOTE: The key speed setting is appli- cable to any key of the same type used on a specific watercraft.
Start engine and make sure wa- TYPICAL tercraft operates properly. Clean the water intake area. If the sys- tem is still clogged, refer to an autho- rized Sea-Doo dealer for servicing. _______________...
Page 102
Inspect water intake grate WARNING for damage. Refer to an authorized If it is necessary to reach in to re- Sea-Doo dealer for repair as neces- move any foreign object caught sary. in the propulsion system, strictly observe the following before pro-...
Page 103
SPECIAL PROCEDURES Models Without a VTS UP/DOWN Button NOTE: On models without the VTS UP/DOWN button, use the UP/DOWN button on the RH handlebar to move the iBR to the desired position once the iBR override function has been ac- tivated as described in the previous steps.
Water trapped in intake manifold would flow towards the engine and possibly cause severe engine damage. Bring the watercraft to an authorized Sea-Doo dealer as soon as possible to smo2013-001-001_a have it serviced. 1. Cross over hose NOTICE...
Page 106
SPECIAL PROCEDURES This page is intentionally blank ______________...
MAINTENANCE SCHEDULE Maintenance is very important for keeping the watercraft in a safe operating con- dition. The watercraft should be serviced as per the maintenance schedule. Disregard the information pertaining to the following systems if the watercraft is not equipped with these features: –...
Page 109
MAINTENANCE SCHEDULE A: ADJUST FIRST 25 HOURS OR 3 MONTHS C: CLEAN EVERY 50 HOURS OR 6 MONTHS I: INSPECT L: LUBRICATE EVERY 100 HOURS OR 1 YEAR R: REPLACE EVERY 200 HOURS OR 2 YEARS O: OPERATOR TO BE PERFORMED BY D: DEALER PART/TASK NOTE...
Page 110
MAINTENANCE SCHEDULE A: ADJUST FIRST 25 HOURS OR 3 MONTHS C: CLEAN EVERY 50 HOURS OR 6 MONTHS I: INSPECT L: LUBRICATE EVERY 100 HOURS OR 1 YEAR R: REPLACE EVERY 200 HOURS OR 2 YEARS O: OPERATOR TO BE PERFORMED BY D: DEALER PART/TASK NOTE...
Page 111
MAINTENANCE SCHEDULE A: ADJUST FIRST 25 HOURS OR 3 MONTHS C: CLEAN EVERY 50 HOURS OR 6 MONTHS I: INSPECT L: LUBRICATE EVERY 100 HOURS OR 1 YEAR R: REPLACE EVERY 200 HOURS OR 2 YEARS O: OPERATOR TO BE PERFORMED BY D: DEALER PART/TASK NOTE...
If not, see XPS Synthetic blend oil at all times. your authorized Sea-Doo watercraft Damages caused by oil which is dealer. not suitable for the engine will not...
Page 113
MAINTENANCE PROCEDURES 7. Remove dipstick again and read CAUTION When operating the oil level. It should be between the engine out of water, the heat ex- FULL and ADD marks. changer in the ride plate may be- come very hot. Avoid any contact with the ride plate as burns may oc- cur.
1. Level between marks when engine is cold is completely flushed and refilled. Re- fer to an authorized Sea-Doo dealer. NOTE: The watercraft is level when it is in water. When on a trailer, raise...
MAINTENANCE PROCEDURES Ignition Coil Installation NOTE: Prior to inserting the ignition coil on its spark plug, apply sealant as IGNITION COIL LUBRI- described in CATION 1. Install coil in cylinder head hole. 2. Push the ignition coil down to se- curely install it on the spark plug tip.
MAINTENANCE PROCEDURES CAUTION When operating the SPARK ENGINE TORQUE engine while the watercraft is out PLUG (in) of the water, the heat exchanger in the ride plate may become very hot. Hand Avoid any contact with ride plate as tighten 0.75 burns may occur.
Inspect ride plate and jet pump wa- 3. Garden hose ter intake grate for damage. See your To flush, start engine then immediately Sea-Doo dealer to have any damaged open the water tap. part repaired or replaced. WARNING CAUTION Certain...
Ensure it slides up and down easily. Check locking mechanism operation. Check fasteners tightness. If some- thing is found defective, don't use ski/wakeboard post and see an autho- rized Sea-Doo dealer for repair. Ski/Wakeboard Post Lubrication TYPICAL Clean ski/wakeboard post and apply 1. Fuse a light coat of SUPER LUBE GREASE 2.
Page 120
MAINTENANCE PROCEDURES smo2011-003-011_c BATTERY AND FUSE ACCESS, FRONT STORAGE COMPARTMENT 1. Battery access panel smo2011-003-009_a TYPICAL 1. Fuse box 2. Fuel tank 3. Front storage compartment (access panel removed) To remove the fuse box cover, squeeze and hold locking tabs on both sides of the fuse box and pull the cover off the fuse box.
Page 121
MAINTENANCE PROCEDURES Fuse Description FUSE RATING DESCRIPTION — Not used 15 A Diagnostic connector START/STOP button GPS (except GTS models) 30 A iBR (except GTS models) 30 A Charge — Not used 30 A Battery — Not used — Not used Depth sounder (if so equipped) Gauge, OTAS and CAPS 10 A...
WATERCRAFT CARE Remove the watercraft from the water marine organisms from engine and/or every day. hull. Apply non-abrasive wax such as silicone wax. Post-Operation Care NOTICE Never clean fiberglass and plastic parts with strong deter- Exhaust System Flushing gent, degreasing agent, paint thin- The exhaust system should be flushed ner, acetone, or other strong chemi- daily when watercraft is used in salt or...
It is recommended that the watercraft against varnish deposits. be serviced by an authorized Sea-Doo dealer for storage, however the follow- WARNING ing operations can be performed by you with a minimum of tools.
Page 124
Electrical System NOTICE Failure to drain the ex- haust system may cause severe Battery Removal and Charging damage to the intercooler (super- Contact your authorized Sea-Doo charged models) and exhaust mani- dealer. fold. WARNING Remove special tools. Never charge or boost the battery Engine Internal Lubrication while installed in the watercraft.
Sea-Doo dealer. compartment. NOTE: It is highly recommended that NOTE: The seat should be left partially an authorized Sea-Doo dealer perform open during storage. This will prevent factory campaigns in addition to the engine compartment condensation preseason preparation, all at the same and possible corrosion.
Page 126
STORAGE AND PRESEASON PREPARATION This page is intentionally blank ______________...
WATERCRAFT IDENTIFICATION The main components of the water- craft (engine and hull) are identified by different serial numbers. It may some- times become necessary to locate these numbers for warranty purposes or to trace the watercraft in the event of theft. Hull Identification Number The Hull Identification Number (HIN) is located on the boarding platform at the...
Manufacturer's EPA Emission Regulations Responsibility All 1999 and more recent Sea-Doo Beginning with 1999 model year en- watercraft manufactured by BRP are gines, PWC manufacturers of marine certified to the EPA as conforming to...
IDI (inductive discharge ignition) Make and type NGK, DCPR8E Spark plug 0.75 mm (.03 in) Battery 12 V, 30 A•h. Electrolyte type PROPULSION Propulsion system Sea-Doo ® jet pump Axial flow, single stage. Type Large hub with 10-vane stator Jet pump Material Aluminum...
Page 131
SPECIFICATIONS WATERCRAFT GTS MODELS DIMENSIONS Length 336.8 cm (132.6 in) Width 123.1 cm (48.5 in) Height 111.8 cm (44 in) WEIGHT AND LOADING CAPACITY Weight (dry) 333 kg (734 lb) Rider capacity 3 (refer to load limit) Storage capacity 116.6 L (30.8 U.S. gal.) Load limit 273 kg (600 lb) (passengers + luggage)
Page 132
Spark plug 0.75 mm (.03 in) Battery 12 V, 30 A•h. Electrolyte type PROPULSION Propulsion system ® Sea-Doo jet pump with iBR (intelligent brake and reverse) Type Axial flow, single stage. Large hub with 10-vane stator Jet pump Material Aluminum...
Page 133
SPECIFICATIONS GTI MODELS WATERCRAFT GTI 130 GTI SE 130 GTI SE 155 GTI LTD 155 DIMENSIONS Length 336.8 cm (132.6 in) Width 123.1 cm (48.5 in) Height 111.8 cm (44 in) WEIGHT AND LOADING CAPACITY Weight (dry) 338 kg (745 lb) Rider capacity 3 (refer to load limit) Storage capacity...
Page 134
Battery 12 V, 30 A•h. Electrolyte type Make and type NGK, DCPR8E Spark plug 0.75 mm (.03 in) PROPULSION Sea-Doo ® jet pump with iBR Propulsion system (intelligent brake and reverse) Axial flow, single stage. Type Large hub with 10-vane stator...
Page 135
SPECIFICATIONS WATERCRAFT GTR MODELS DIMENSIONS Length 336.8 cm (132.6 in) Width 123.1 cm (48.5 in) Height 111.8 cm (44 in) WEIGHT AND LOADING CAPACITY Weight (dry) 348 kg (767 lb) Rider capacity 3 (refer to load limit) Storage capacity 116.6 L (30.8 U.S. gal.) Load limit 273 kg (600 lb) (passengers + luggage)
Page 136
Battery 12 V, 30 A•h. Electrolyte type Make and type NGK, DCPR8E Spark plug 0.75 mm (.03 in) PROPULSION Sea-Doo ® jet pump with iBR Propulsion system (intelligent brake and reverse) Axial flow, single stage. Type Large hub with 10-vane stator...
Page 137
SPECIFICATIONS WATERCRAFT WAKE MODEL DIMENSIONS Length 336.8 cm (132.6 in) Width 123.1 cm (48.5 in) Height 111.8 cm (44 in) WEIGHT AND LOADING CAPACITY Weight (dry) 339 kg (748 lb) Rider capacity 3 (refer to load limit) Storage capacity 116.6 L (30.8 U.S. gal.) Load limit 273 kg (600 lb) (passengers + luggage)
Page 138
SPECIFICATIONS This page is intentionally blank ______________...
– Refer to WATER-FLOODED ENGINE in SPECIAL PROCEDURES. 7. Faulty sensor or ECM. – Refer to an authorized Sea-Doo dealer. 8. Seized jet pump. – Try to clean. Otherwise, refer to an authorized Sea-Doo dealer. ENGINE CRANKS SLOWLY 1. Loose battery cable connections. – Check/clean/tighten.
Page 141
– Refer to WATER-FLOODED ENGINE in SPECIAL PROCEDURES. 5. Engine management system fault detected (check engine pilot lamp is ON). – Refer to an authorized Sea-Doo dealer. 6. Faulty fuel pump. – Refer to an authorized Sea-Doo dealer. ENGINE MISFIRES, RUNS IRREGULARLY 1.
Page 142
– Clean. Refer to JET PUMP WATER INTAKE AND IMPELLER CLEANING in SPECIAL PROCEDURES section. 4. Damaged impeller or worn-out wear ring. – Replace. Refer to an authorized Sea-Doo dealer. 5. Engine oil level too high. – Refer to an authorized Sea-Doo dealer.
Page 143
– Release the throttle to idle RPM. – Press the CRUISE button to activate the slow speed mode. – Return to shore using the slow speed mode. Refer to an authorized Sea-Doo dealer. iBR WILL NOT RETURN TO NEUTRAL POSITION (IBR INDICATOR LIGHT ON) 1.
MODE or SET button must be pressed once. There is no time out on When a fault occurs, see an authorized this function. Sea-Doo dealer as soon as possible for inspection. Fault Codes When a fault occurs, a numerical fault code may be recorded depending on the fault type and system.
The fault indicators and messages displayed in the information center will inform you of a particular condition or if an anomaly occurs. If a fault indicator or a fault message comes ON in the multifunction gauge, contact your authorized Sea-Doo dealer. MULTIFUNCTION GAUGE For information on usual function indicators, refer to section as applicable to model.
Page 146
MONITORING SYSTEM MESSAGE DISPLAY INFORMATION RIGHT KEYPAD ERROR Gauge control button malfunction LOW OIL PRESSURE Engine low oil pressure detected HIGH EXHAUST TEMPERATURE High exhaust temperature detected High engine temperature detected HIGH TEMPERATURE Engine system malfunction or CHECK ENGINE maintenance required HIGH BATTERY VOLTAGE High battery voltage detected LOW BATTERY VOLTAGE...
Refer to an authorized Sea-Doo dealer. Low oil pressure. Turn off engine as soon as possible. Check oil level and refill. Refer to an authorized Sea-Doo dealer. NOTICE If the monitoring beeper continuously sounds, stop engine as soon as possible.
Page 148
MONITORING SYSTEM This page is intentionally blank ______________...
(2) the Sea-Doo personal watercraft has been altered or modified in such a way so as to adversely affect its operation, performance or durability, or has been altered or modified to change its intended use.
Page 151
BRP’s standard limited warranty until the end of such regular coverage period. 4. For Sea-Doo personal watercrafts produced by BRP for sale in the State of Cal- ifornia that are originally sold to a resident or subsequently warranty registered to a resident in the State of California, please also refer to the applicable Califor- nia Emissions Control Warranty Statement contained herein.
Page 152
BRP dealer during the applicable warranty coverage period under the conditions described herein. No claim of breach of warranty shall be the cause for cancellation or rescission of the sale of the Sea-Doo personal watercraft to the owner. In the event that service is required outside of the country of original sale, the...
Page 153
8. TRANSFER If the ownership of a product is transferred during the warranty coverage period, this warranty shall also be transferred and be valid for the remaining coverage period provided that BRP is notified of such transfer of ownership in the following way: 1.
® ENGINES For California, your 2013 Sea-Doo personal watercraft has a special environmental label required by the California Air Resources Board. The label has 1, 2, 3 or 4 stars. A hangtag, provided with your personal watercraft, describes the meaning of the star rating system.
The California Air Resources Board and Bombardier Recreational Products Inc. (“BRP”) are pleased to explain the emission control system warranty on your Model Year 2013 Sea-Doo personal watercraft. In California, new personal water- craft engines must be designed, built and equipped to meet the State’s stringent anti-smog standards.
Page 156
Parts covered for a Model Year 2013 Sea-Doo ® personal watercraft equipped with 4-TEC ® engines: Idle bypass valve Air intake adapter Throttle position sensor Spark plugs Intake manifold air pressure sensor Ignition coils Intake manifold air temperature sensor Air box...
Page 157
Owner’s Warranty Responsibilities As the owner of a 2013 Sea-Doo personal watercraft, you are responsible for the performance of the required maintenance listed in your Operator’s Guide. BRP recommends that you retain all receipts covering maintenance your personal watercraft engine, but BRP cannot deny warranty solely for the lack of receipts or your failure to ensure the performance of all scheduled maintenance.
All genuine BRP personal watercraft parts and accessories, installed by an autho- rized BRP Sea-Doo distributor/dealer at the time of delivery of the 2013 Sea-Doo personal watercraft, carry the same warranty as that of the personal watercraft.
Page 159
Sea-Doo Distributor/Dealer; – Damage caused by abuse, misuse, abnormal use, neglect, racing, improper operation or operation of the product in a manner inconsistent with the recom- mended operation described in the Operator’s Guide;...
Page 160
This warranty coverage is available only if each of the following conditions has been fulfilled: – The 2013 Sea-Doo personal watercraft must be purchased as new and unused by its first owner from a Sea-Doo Distributor/Dealer authorized to distribute Sea- Doo personal watercrafts in the country in which the sale occurred;...
Page 161
No claim of breach of warranty shall the cause for cancellation or rescission of the sale of the Sea-Doo personal watercraft to the owner. You may have other legal rights which may vary from country to country.
Page 162
For all other countries, please contact your local Sea-Doo Distributor/Dealer (visit our website at www.brp.com for contact information), or contact our North American office at: BOMBARDIER RECREATIONAL PRODUCTS INC. Consumer Assistance Center 75 J.-A. Bombardier Street Sherbrooke QC J1L 1W3 Tel.: +1 819 566-3366...
All genuine BRP personal watercraft parts and accessories, installed by an autho- rized Sea-Doo Distributors/Dealers at the time of delivery of the 2013 Sea-Doo per- sonal watercraft carry the same warranty as that of the personal watercraft.
Page 164
Sea-Doo Distributor/Dealer; – Damage caused by abuse, misuse, abnormal use, neglect, racing, improper operation or operation of the product in a manner inconsistent with the recom- mended operation described in the Operator’s Guide;...
Page 165
This warranty coverage is available only if each of the following conditions has been fulfilled: – The 2013 Sea-Doo personal watercraft must be purchased as new and unused by its first owner from a Sea-Doo Distributor/Dealer authorized to distribute Sea- Doo personal watercrafts in the country in which the sale occurred;...
Page 166
9. CONSUMER ASSISTANCE 1. In the event of a controversy or a dispute in connection with this limited warranty, BRP suggests that you try to resolve the issue at the Sea-Doo Distributor/Dealer level. We recommend discussing the issue with the autho- rized Sea-Doo Distributor/Dealer's service manager or owner.
Page 167
ADDITIONAL TERMS AND CONDITIONS FOR FRANCE ONLY The following terms and conditions are applicable to products sold in France only: The seller shall deliver goods that are complying with the contract and shall be re- sponsible for defects existing upon delivery. The seller shall also be responsible for defects resulting from packaging, assembling instructions or the installation when it is its responsibility per the contract or if accomplished under its responsibility.
Page 168
This page is intentionally blank ______________...
PRIVACY INFORMATION BRP wishes to inform you that your coordinates will be used for safety and war- ranty related purposes. Furthermore, BRP and its affiliates may use its customer list to distribute marketing and promotional information about BRP and related products.
CHANGE OF ADDRESS/OWNERSHIP If your address has changed or if you are the new owner of the watercraft, be sure to notify BRP by either: – Mailing one of the following card below; – North America Only: calling at 715 848-4957 (USA) or 819 566-3366 (Canada); –...
Page 172
CHANGE OF ADDRESS/OWNERSHIP This page is intentionally blank ______________...
Page 173
CHANGE OF ADDRESS/OWNERSHIP ______________...
Page 174
CHANGE OF ADDRESS/OWNERSHIP ______________...
Need help?
Do you have a question about the GTS Series and is the answer not in the manual?
Questions and answers