Table of Contents
Advertisement
Quick Links
MaNufactuRINg
NuMbeRs:
9300300
9300302
9300304
9300306
9300308
9300309
9300320
9300321
9300322
9300324
9300330
9300331
9300332
9300334
9300336
9300376
9300340
9300341
9300342
9300344
9300350
9300351
9300352
9300356
9300357
9300360
9300374
9300376
9300380
C
US
CM
P/N 1010609 Rev. I 03/12
Hot Dog Corral
C
US
owner
Model HDC
Series 9300000
s Manual
'
Advertisement
Table of Contents
Related Manuals for Roundup HDC 9300300
Summary of Contents for Roundup HDC 9300300
- Page 1 MaNufactuRINg NuMbeRs: 9300300 9300302 9300304 9300306 9300308 9300309 9300320 9300321 9300322 9300324 9300330 9300331 9300332 9300334 9300336 9300376 9300340 9300341 9300342 9300344 9300350 9300351 9300352 9300356 Hot Dog Corral 9300357 9300360 9300374 9300376 Model HDC 9300380 Series 9300000 P/N 1010609 Rev. I 03/12 owner s Manual ’...
-
Page 2: Table Of Contents
Information General Please read the full text of the Limited Warranty in this the Roundup Hot Dog corral is a unique and innova- manual. tive way to grill hot dogs. the hot dogs are placed in a “corral” that moves up-and-down over a heated flat If the unit arrives damaged, contact the carrier imme- grill surface. -
Page 3: Service/Technical Assistance
Roundup replacement parts in this Purchased from: unit. use of replacement parts other than those sup- plied by the manufacturer will void the warranty. Your... - Page 4 Hot Dog Corral ImpOrtant safety InfOrmatIOn (continued) In addition to the warnings and cautions in this manual, • warnInG eleCtrICal sHOCK HazarD. use the following guidelines for safe operation of the faIlure tO fOllOw tHese InstruCtIOns COulD result In serIOus Injury Or unit: DeatH.
-
Page 5: Specifications
Hot Dog Corral speCIfICatIOns electrical ratings CautIOn all electrical connections must be in accordance model & Volts watts amp. with local electrical codes and any other appli- mfg. no. cable codes. HDc-20 1000 50/60 warnInG eleCtrICal sHOCK HazarD. faIlure tO HDc-20 1000 50/60... -
Page 6: Dimensions
Hot Dog Corral speCIfICatIOns (continued) Dimensions model & width Depth Height shipping mfg. no. weight 18 3/4” 21 1/2” 8 1/4” 55 lbs. HDc-20 (476 mm) (545 mm) (210 mm) (25 kg) 18 3/4” 21 1/2” 8 1/4” 55 lbs. HDc-20Rc (476 mm) (545 mm) -
Page 7: Installation
Hot Dog Corral InstallatIOn unpacking Driver frame 1. Remove unit and all packing materials from shipping carton. 2. Open the large box. Remove all packing materials and protective coverings from the unit and parts. nOte: If any parts are missing or damaged, contact antunes technical service ImmeDIately at 1-877-392-7854. -
Page 8: Food Shield (Optional)
Hot Dog Corral InstallatIOn (continued) food shield (Optional) Item part Description Qty. nOte: early style corrals do not have weldnuts on inside of side covers. when installing the food 2120121 spacer shield, jamnuts (5, figure 2) must be used. 3080158 screw, Pan Hd., #8-32 x 5/8”... -
Page 9: Operation
Hot Dog Corral OperatIOn General rocker switch (power On/Off) Volume, preference and experience will determine what temperature setting is best for your operation. When holding hot dogs for long periods of time, it is recom- mended to keep the setting under 160°f (71°c). this may vary depending on the type of hot dog used and the production rate required. -
Page 10: Maintenance
Hot Dog Corral maIntenanCe Inspecting and aligning Drive parts CautIOn Chlorides or phosphates in cleaning agents (e.g. If the Drive frame does not move smoothly, or during a bleach, sanitizers, degreasers or detergents) Motor replacement, inspect and align the drive parts as could cause permanent damage to stainless steel follows: equipment. -
Page 11: Replacing The Black Nylon Glides
Hot Dog Corral maIntenanCe (continued) HDC-21a/35a Only: Remove the four Retainer Rings left side Cover and glides (figure 6). Install new glides and secure with Retainer Rings. Driver roller Driver frame w/ roller rods HDC-20/30a/50a Only: using a small screwdriver, pry the four glides up and out of the unit (figure 6a). -
Page 12: Technical Theory Of Operation
Hot Dog Corral teCHnICal tHeOry Of OperatIOn Hot Dog Corral technical theory of the heating circuit(s) will cycle on and off as needed, even at idle. the hot dogs are placed between the Operation Roller Rods of the sliding Driver frame assembly. as When the Rocker switch (Power On/Off) is ON, voltage the Drive Motor runs, it operates a linkage system flows to the capillary bulb thermostat(s), Drive Motor... -
Page 13: Troubleshooting
Hot Dog Corral trOublesHOOtInG warnInG to avoid possible personal injury and/or damage to the unit, inspection, test and repair of electrical equip- ment should be performed by qualified service personnel. the unit should be unplugged when servicing. problem possible Cause Corrective action unit will not heat up. -
Page 14: Replacement Parts
Hot Dog Corral replaCement parts HDC-20/20rC INSET A See Inset A DRIVE PARTS P/N 1010609 Rev. I 03/12 A.J. Antunes & Co. - Page 15 4030232 Heating element, 230V 325P166* setscrew, 1/4-28 x 3/8” 1000 Watt 306P104* screw, #6-32 x 1/4” 20 7000215 Thermostat Kit F° 1000136 Roundup emblem 7000213 Thermostat Kit C° ns 040K108 Nylon Bushing & Retainer Kit 4010151 Rocker switch, (Incl. #33, 34, & 37) Power On/Off, 120V ns 7000193...
- Page 16 Hot Dog Corral replaCement parts (continued) HDC-21a/30a/35a/50a INSET A See Inset A DRIVE PARTS P/N 1010609 Rev. I 03/12 A.J. Antunes & Co.
- Page 17 Hot Dog Corral replaCement parts (continued) HDC-21a/31a/35a/50a Item part no./Qty. Description HDC-21a HDC-30a HDC-35a HDC-50a 0010366 / 1 0020595 / 1 0010368 / 1 7000410 / 1 Driver assy., standard 0011583 / 1 0020989 / 1 0011584 / 1 0021448 / 1 Driver assy., 10 rods, special Order 7000383 / 1 7000384 / 1...
- Page 18 (some Models) – – – 1001079 / 1 Label, timer (some Models) 1000136 / 1 1000136 / 1 1000136 / 1 1000136 / 1 Roundup emblem – – – 304P105* / 4 Nut, Hex, KEPS, #4-40 – – – 308P223* / 4 Washer, flat #8...
-
Page 19: Wiring Diagrams
Hot Dog Corral wIrInG DIaGrams HDC-20/20rC HDC-21a/30a/35a HDC-50a WIRING DIAGRAM POWER CORD NOTE: ALL WIRES TO BE 16 GA. AWM-105°C UNLESS OTHERWISE SPECIFIED: # 14 GA. TFE-200°C 16 GA. TFE-200°C 16 GA. PVC-200°C o 18 GA. AWM-105°C 20 GA. XLP-200°C Δ... -
Page 20: Limited Warranty
2 hours (100 miles/160 km) round trip from the nearest authorized service agency. 2. Roundup reserves the right to make changes in design or add any improvements on any product. the right is always reserved to modify equipment because of factors beyond our control and government regulations.