Advertisement
!
NOTE
1. In the AUTO mode, the air conditioner can logically choose
the mode of COOL, FAN , HEAT and DRY by sensing the
difference between the actual ambient room temperature and
the set temperature on the remote controller.
2. If the AUTO mode is not comfortable for you, the desired
mode can be selected manually.
COOL/ HEAT (Cooling only model without) and
FAN ONLY Operation
1. If the AUTO mode is not comfortable, you may manually over-
ride the settings by using COOL, HEAT or FAN ONLY modes.
2. Push the TEMP button to set the desired room temperature.
When in COOL mode, the most comfortable settings are 21 C
or above. When in HEAT mode, the most comfortable
。
settings are 28 C or b elow.
3. Push the FAN SPEED to select the FAN mode of AUTO, HIGH,
MED or LOW.
4. Push the ON/OFF button, the operation lamp lights and the air
conditioner start to operate as your settings. Push the ON/OFF
button again to stop this unit operation.
NOTE
!
The FAN ONLY mode can not be used to control the temperature.
While in this mode, only steps 1,3 and 4 may be performed.
DRY Operation
1. Push the MODE button to select DRY.
2. Push the TEMP button to set the desired temperature from
。
。
21 C to 2 8 C.
3. Push the ON/OFF button, the operation lamp lights and the air
conditioner start to operate in the DRY mode. FAN SPEED is
Low. Push the ON/OFF button again to stop this unit operation.
NOTE
!
Due to the difference of the set temperature of the unit and
the actual indoor temperature, the Air Conditioner when in
DRY mode will automatically operate many times without
running the COOL and FAN mode.
5
TEMP Button
: Press the button to decrease the indoor
1
temperature setting.
TEMP Button
: Press the button to increase the indoor
2
temperature setting.
ON/OFF Button: Push this button to start the unit operation.
3
Push the button again to stop the unit operation.
4
MODE Select Button: Each time you push the button, a mode
is selected in a sequence that goes from AUTO、COOL、
DRY、HEAT and FAN, as the following figure indicates:
AUTO
COOL
NOTE: COOL only model has no HEAT feature.
!
SWING Button: Push this button, the louver would swing up
5
。
and down automatically. Push again to stop it .
RESET Button: When the RESET button is pushed, all of
6
the current settings are cancelled and the control will return to
the initial settings.(Use a φ1mm little round stick to push the
button )
AIR DIRECTION Button: Push this button, the louver can be fixed
7
at a desired angle. The louver swing(upward or downward) to
a certain angle for each press. When the louver swing at an angle
which would affect the cooling and heating efficiency of the air
conditioner, it would automatically change the swing direction
(upward or downward).
FAN SPEED Button: This button is used for setting Fan Speed
8
in the sequence that goes from AUTO、LOW 、MED to HIGH,
then back to Auto.
TIMER ON Button: Press this button to preset the time ON(start
9
to operate). Each press will increase the time ON setting in 30
minutes increments. When the setting time displays 10:00, each
press will increase the time ON setting in 60 minutes increments.
To cancel the time ON program, simply adjust the time ON to 0:00.
ECONOMIC RUNNING Button: Press this button to go into the
10
Energy-Saving operation mode. Press the button again to cancel.
TIMER OFF Button: Press this button to preset the time OFF
11
(turn off the operation). Each press will increase the time OFF
setting in 30 minutes increments. When the setting time displays
10:00, each press will increase the time OFF setting in 60
minutes increments. To cancel the time OFF program, simply
adjust the time OFF to 0:00
DRY
HEAT
FAN
2
Advertisement
