Sony SPP-ID300 Service Manual
  1. Manuals
  2. Brands
  3. Sony Manuals
  4. Cordless Telephone
  5. SPP-ID300
  6. Service manual
Sony SPP-ID300 Service Manual

Sony SPP-ID300 Service Manual

Hide thumbs Also See for SPP-ID300:
Table of Contents

Advertisement

Quick Links

SERVICE MANUAL
Subject: BASE (MAIN) and HAND (MAIN) boards Modification
1.
DISCRIMINATION
On this set, the boards have been changed in the midway of production.
Refer to this service manual supplement-1, if the serial number given on the bottom of the base unit is as listed below.
If the given serial number does not correspond to the following table, refer to original service manual (9-925-742-11) .
Model
SPP-ID300: US model
SPP-ID300: Canadian model
SPP-ID400: US model
SPP-ID400: Canadian model
SPP-ID300/ID400
SUPPLEMENT-1
File this supplement with the service manual.
Serial Number
220,007 and later
113,004 and later
254,010 and later
279,016 and later
Serial Number
US Model
Canadian Model
(ENG-99003)

Advertisement

Table of Contents
loading

Related Manuals for Sony SPP-ID300

Summary of Contents for Sony SPP-ID300

  • Page 1 Refer to this service manual supplement-1, if the serial number given on the bottom of the base unit is as listed below. If the given serial number does not correspond to the following table, refer to original service manual (9-925-742-11) . Model Serial Number SPP-ID300: US model 220,007 and later SPP-ID300: Canadian model 113,004 and later...

  • Page 2: Table Of Contents

    DIAGRAMS 4-1. Note for Printed Wiring Boards and Schematic Diagrams ............13 4-2. Printed Wiring Board – BASE UNIT Section (SPP-ID300) – ......15 4-3. Schematic Diagram – BASE UNIT Section (SPP-ID300) – ......17 4-4. Printed Wiring Boards – BASE UNIT Section (SPP-ID400) – ......19 4-5.

  • Page 3: Test Mode

    TEST MODE (SPP-ID300) Note: See the original service manual for SPP-ID400. 2-1. BASE UNIT [Setting the Test Mode] 1. Power on with press the [PAGE] key for two seconds. 2. CHARGE LED turns on for one second, and the Test Mode is set.
  • Page 4 [Test Mode Execution] Press the [PAGE] key to execute any of the following tests: PLL IC Hard control control (IC2) (IC1) Test Mode Step Name VCO/TX FREQ. ADJ TX MODE CHECK TX DATA 1 RX ADJ DUPLEX DATA IN CHECK RSSI CHECK BELL CHECK CHARGE CHECK...

  • Page 5: Handset

    2-2. HANDSET [Setting the Test Mode] Power on with press the [*] key and the [#] key simultaneously for one second, and the Test Mode is set. Press the [SPEED DIAL] key in Test Mode, EEPROM (IC501) is been initialize, and it beeps confirm tone. LIQUID CRYSTAL DISPLAY turns on/off, when press the [#] key.
  • Page 6 [Test Mode Execution] Press the each key for the desired Test Mode step to execute any of the following tests: PLL IC Hard control control (IC503) (IC504) Test Mode Step Name VCO/TX FREQ. ADJ TX MODE CHECK TX DATA RX ADJ RX CHECK BELL HIGH BELL LOW...

  • Page 7: Electrical Adjustments

    TP (RX VCO) – TP (GND) (SPP-ID300) 3. When press the [PAGE] key (S4) (SPP-ID300) or the [INTERCOM] key (S3) (SPP-ID400) , check that the frequency Procedure: of frequency counter (channel) is changed each time the key is 1. Connect a digital voltmeter to TP (RX VCO) and TP (GND).
  • Page 8 4. Set the [DIAL MODE] switch (S1) to the [T] (TONE) position (SPP-ID300) . noise meter 5. Press the [PAGE] key (S4) (SPP-ID300) or the [INTERCOM] key (S3) (SPP-ID400) four times to change the channel to 11CH. TP (DISC) 6. Adjust L6 to get maximum reading on the SINAD meter.
  • Page 9 1. Change the modulation of SSG to 200 Hz (±4 kHz deviation). 2. Set the [DIAL MODE] switch (S1) to the [P] (PULSE) position (SPP-ID300) . 3. Press the [PAGE] key (S4) eleven times (SPP-ID300) or the [SPEAKERPHONE] key (S2) twice (SPP-ID400) to change the test mode step to DATA IN CHECK.

  • Page 10: Handset

    5. Modulation Sensitivity Check HANDSET Setting: • Make the set in test mode. (See page 3) AF OSC 600 Ω – TX Adjustment and Check – TP (MIC +) 1. TX VCO Adjustment TP (MIC –) – – – Setting: 1 kHz, 20 mV digital voltmeter deviation meter...
  • Page 11 – RX Adjustment and Check – 4. Sensitivity Adjustment Setting: 1. RX VCO Voltage Check Setting: TP (ANT) digital voltmeter TP (GND) Carrier frequency: 46.97 MHz Modulation: 1 kHz, ± 3 kHz deviation Output level: 20 dB µ EMF TP (RX VCO) –...
  • Page 12 5. RSSI ON/OFF Level Check 6. Data in Check Setting: Setting: TP (ANT) TP (ANT) TP (GND) TP (GND) Carrier frequency: 46.77 MHz Carrier frequency: 46.77 MHz Modulation: off, ± 0 kHz deviation Modulation: 200 Hz, ± 4 kHz deviation Output level: 10 dB µ...

  • Page 13: Diagrams

    GAIN CELL DETECTOR REGULATOR Parts face side: Parts on the parts face side seen from BUFFER SUM AMP (2.15V) 2 IC2 !¢ (X2) (SPP-ID300) (Side A) the parts face are indicated. LIMITER IC2 %∞ (X2) (SPP-ID400) – PROGRAMMABLE COUNTER VREF...

  • Page 14: Printed Wiring Board - Base Unit Section (Spp-Id300)

    SPP-ID300/ID400 4-2. PRINTED WIRING BOARD – BASE UNIT Section (SPP-ID300) – • Semiconductor Location Ref. No. Location F-10 B-10 F-10 D101 D102 D103 D104 D105 D106 D107 D108 D109 D110 D111 D-10 IC101 IC103 D-10 – 15 – – 16 –...
  • Page 15 SPP-ID300/ID400 4-3. SCHEMATIC DIAGRAM – BASE UNIT Section (SPP-ID300) – • See page 13 for Waveforms. • See page 14 for IC Block Diagram. – 17 – – 18 –...

  • Page 16: Printed Wiring Boards - Base Unit Section (Spp-Id400)

    SPP-ID300/ID400 4-4. PRINTED WIRING BOARDS – BASE UNIT Section (SPP-ID400) – • Semiconductor Location Ref. No. Location F-10 F-10 D101 D102 D103 D104 D105 D106 D107 D108 D109 D110 D111 D112 D-10 IC101 IC103 D-10 – 20 – – 19 –...
  • Page 17 SPP-ID300/ID400 4-5. SCHEMATIC DIAGRAM – BASE UNIT Section (SPP-ID400) – • See page 13 for Waveforms. • See page 14 for IC Block Diagram. – 21 – – 22 –...

  • Page 18: Printed Wiring Board - Handset Section

    SPP-ID300/ID400 4-6. PRINTED WIRING BOARD – HANDSET Section – • Semiconductor Location Ref. No. Location D501 D502 F-10 D503 F-11 D504 D505 F-10 D506 F-10 D510 E-11 D511 F-11 D514 F-10 IC502 E-10 IC503 IC504 IC505 F-10 Q501 Q502 E-10...
  • Page 19 SPP-ID300/ID400 4-7. SCHEMATIC DIAGRAM – HANDSET Section – • See page 13 for Waveforms. • See page 14 for IC Block Diagram. – 25 – – 26 –...

  • Page 20: Exploded Views

    BASE (MAIN) EXPLODED VIEWS ELECTRICAL PARTS LIST NOTE: DIFFERENCE PARTS LIST • Items marked “*” are not stocked since they • Due to standardization, replacements in the When indicating parts by reference Page FORMER parts list may be different from the parts speci- are seldom required for routine service.
  • Page 21 BASE (MAIN) Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark 1-163-009-11 CERAMIC CHIP 0.001uF C104 1-164-492-11 CERAMIC CHIP 0.15uF 1-163-809-11 CERAMIC CHIP 0.047uF C105 1-165-319-11 CERAMIC CHIP 0.1uF C106 1-163-009-11 CERAMIC CHIP 0.001uF 1-107-682-11 CERAMIC CHIP C107 1-115-871-11 ELECT 1-163-021-11 CERAMIC CHIP...
  • Page 22 BASE (MAIN) Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark 8-719-055-76 DIODE 1N4148 (ID300) 1-412-003-31 INDUCTOR CHIP 5.6uH 8-719-976-19 DIODE RLS-4148 (ID400) 1-415-984-11 COIL, DETECTION 1-410-509-11 INDUCTOR 10uH 8-719-055-76 DIODE 1N4148 1-412-699-11 INDUCTOR 0.56uH 8-719-055-76 DIODE 1N4148 (ID300) 8-719-976-19 DIODE RLS-4148 (ID400) 1-415-978-11 COIL, RF 8-719-055-54 LED LTL-16KPE (NEW CALL)
  • Page 23 BASE (MAIN) Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark 1-216-025-00 METAL CHIP 1/10W 1-216-689-11 METAL CHIP 1/10W 1-216-037-00 METAL CHIP 1/10W 1-216-129-00 METAL CHIP 2.2M 1/10W 1-216-041-11 METAL CHIP 1/10W 1-216-085-00 METAL CHIP 1/10W 1-216-071-00 METAL CHIP 8.2K 1/10W 1-216-069-11 RES, CHIP...
  • Page 24 BASE (MAIN) Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark 1-216-049-11 METAL CHIP 1/10W R136 1-216-065-00 METAL CHIP 4.7K 1/10W (ID400) (ID400) 1-216-097-00 METAL CHIP 100K 1/10W R137 1-216-065-00 METAL CHIP 4.7K 1/10W (ID300) (ID400) 1-216-099-00 METAL CHIP 120K 1/10W R138...
  • Page 25 BASE (MAIN) BASE MICROPHONE Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark R172 1-249-417-11 CARBON 1/10W R210 1-216-097-00 METAL CHIP 100K 1/10W (ID400) R211 1-216-097-00 METAL CHIP 100K 1/10W R173 1-216-295-00 METAL CHIP 1/10W R212 1-216-089-00 METAL CHIP 1/10W (ID400) R213...
  • Page 26 HAND (MAIN) Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark A-3672-717-A HAND (MAIN) BOARD, COMPLETE (ID400) A-3672-719-A HAND (MAIN) BOARD, COMPLETE (ID300) C557 1-163-021-11 CERAMIC CHIP 0.01uF C558 1-164-004-11 CERAMIC CHIP 0.1uF **************************** C559 1-163-021-11 CERAMIC CHIP 0.01uF 3-020-038-01 CONTACT (ANTENNA) C560...
  • Page 27 HAND (MAIN) Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark IC503 8-759-572-65 IC MB89538PFM-G-108-BND (ID300) R516 1-216-295-00 METAL CHIP 1/10W IC504 8-759-641-03 IC KB8527BQ-2 R517 1-216-049-11 METAL CHIP 1/10W IC505 8-759-193-04 IC RN5RG33AA-TL R518 1-216-025-00 METAL CHIP 1/10W R519 1-216-081-00 METAL CHIP...
  • Page 28 SPP-ID300/ID400 HAND (MAIN) Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark R577 1-216-103-00 RES, CHIP 180K 1/10W R578 1-216-097-00 METAL CHIP 100K 1/10W R579 1-216-073-00 METAL CHIP 1/10W R580 1-216-113-00 METAL CHIP 470K 1/10W R581 1-216-198-00 METAL CHIP...

This manual is also suitable for:

Spp-id400

Table of Contents