Maintenance - AEG SBE 500 R Original Instructions Manual

TECHNICAL DATA
Rated input ..............................................................................
Output ......................................................................................
No-load speed .........................................................................
1st gear .................................................................................
2nd gear ...............................................................................
Speed under load max. ...........................................................
1st gear .................................................................................
2nd gear ...............................................................................
Percussion rate........................................................................
Rate of percussion under load max. ........................................
Static jamming moment*, 1st gear/2nd gear ...........................
Drilling capacity in concrete .....................................................
Drilling capacity in brick and tile ..............................................
Drilling capacity in steel ...........................................................
Drilling capacity in aluminium ..................................................
Drilling capacity in wood ..........................................................
Drill opening range ..................................................................
Drive shank..............................................................................
Chuck neck diameter ...............................................................
Weight without cable ...............................................................
Typical weighted acceleration in the hand-arm area ...............
Typical A-weighted sound levels:
Sound pressure level (K = 3 dB(A)) ..........................................
Sound power level (K = 3 dB(A)) ..............................................
Measured values determined according to EN 60 745.
The data stated above apply for models with 230 - 240 V.
In case of deviating mains voltage, the data stated on the rating plate are applicable.
* Measured according to AEG norm N 877318
WARNING! Read all safety warnings and all
instructions, including those given in the accompanying
brochure. Failure to follow the warnings and instructions
may result in electric shock, fire and/or serious injury.
Save all warnings and instructions for future reference.
SAFETY INSTRUCTIONS
Wear ear protectors. Exposure to noise can cause hearing
loss.
Use auxiliary handles supplied with the tool. Loss of
control can cause personal injury.
Hold power tool by insulated gripping surfaces, when
performing an operation where the cutting accessory
may contact hidden wiring or its own cord. Contact with
a „live" wire will also make exposed metal parts of the power
tool „live" and shock the operator.
Appliances used at many different locations including open
air must be connected via a current surge preventing switch.
Always wear goggles when using the machine. It is
recommended to wear gloves, sturdy non slipping shoes
and apron.
Sawdust and splinters must not be removed while the
machine is running.
Always disconnect the plug from the socket before carrying
out any work on the machine.
Only plug-in when machine is switched off.
Keep mains lead clear from working range of the machine.
Always lead the cable away behind you.
Do not use diamond core drills on hammer mode.
When working in walls ceiling, or floor, take care to avoid
electric cables and gas or waterpipes.
SPECIFIED CONDITIONS OF USE
The electronic drill/screwdriver can be universally used for
drilling, percussion drilling, screwdriving and cutting screw
threads.
Do not use this product in any other way as stated for
normal use.
18 ENGLISH
SBE 500 R SBE 570 R SBE 600 R SBE 630 R
..... 500 W ...........570 W ............ 600 W .............630 W .............630 W
..... 250 W ...........285 W ............ 300 W .............315 W .............315 W
0-2650 min . 0-2700 min ...0-2800 min ... 0-2800 min
-1 -1 -1 -1
..........- .................. - .....................- ..................... - ..............2250 min
..........- .................. - .....................- ..................... - ..............2800 min
... 1800 min .....1600 min ...... 1300 min .......1300 min
-1 -1 -1 -1
..........- .................. - .....................- ..................... - ................850 min
..........- .................. - .....................- ..................... - ..............1300 min
. 39750 min -1 ...40500 min -1 .... 42000 min -1 .....42000 min -1
. 27000 min ...24000 min .... 19500 min .....19500 min
-1 -1 -1 -1
....... 21 Nm ...........23 Nm ............ 23 Nm .............23 Nm ........25/24 Nm
....... 13 mm ..........15 mm ............ 15 mm .............15 mm ............13 mm
....... 15 mm ..........18 mm ............ 18 mm .............18 mm ............15 mm
....... 10 mm ..........13 mm ............ 13 mm .............13 mm ............13 mm
....... 10 mm ..........13 mm ............ 13 mm .............13 mm ............13 mm
....... 20 mm ..........30 mm ............ 30 mm .............30 mm ............30 mm
.1,5-10 mm ... 1,5-13 mm ......1,5-13 mm ...... 1,5-13 mm ..... 1,5-13 mm
1/2"x20 ........1/2"x20 .......... 1/2"x20 ...........1/2"x20 ..........1/2"x20
....... 43 mm ..........43 mm ............ 43 mm .............43 mm ............43 mm
...... 1,6 kg ............1,7 kg ............. 1,7 kg ..............1,7 kg .............1,7 kg
......... 9 m/s 2 ...........9 m/s 2 ............. 9 m/s 2 ..............9 m/s 2
........95 dB (A) .......95 dB (A) ......... 95 dB (A) ......... 95 dB (A) .........95 dB (A)
......106 dB (A) .....106 dB (A) ....... 106 dB (A) ....... 106 dB (A) .......106 dB (A)
EC-DECLARATION OF CONFORMITY
We declare under our sole responsibility that this product is
in conformity with the following standards or standardized
documents. EN 60745, EN 55014-1, EN 55014-2,
EN 61000-3-2, EN 61000-3-3, in accordance with the
regulations 98/37/EC, 2004/108/EC
Rainer Kumpf
Winnenden, 2008-01-16
Manager Product Development
MAINS CONNECTION
Connect only to single-phase a.c. current and only to the
system voltage indicated on the rating plate. It is also
possible to connect to sockets without an earthing contact
as the design conforms to safety class II.

MAINTENANCE

The ventilation slots of the machine must be kept clear at all
times.
If the machine is mainly used for percussion drilling,
regularly remove collected dust from the chuck. To remove
the dust hold the machine with the chuck facing down
vertically, and completely open and close the chuck. The
collected dust will fall from the chuck. It is recommended to
regularly use cleaner for the clamping jaws and the
clamping jaw borings.
Use only AEG accessories and spare parts. Should
components need to be exchanged which have not been
described, please contact one of our AEG service agents
(see our list of guarantee/service addresses).
If needed, an exploded view of the tool can be ordered.
Please state the ten-digit No. as well as the machine type
printed on the label and order the drawing at your local
service agents or directly at: AEG Elektrowerkzeuge,
Max-Eyth-Straße 10, D-71364 Winnenden, Germany.
SB2-630 SYMBOLS
Please read the instructions
.......2800 min
-1
carefully before starting the
-1
machine.
-1
-1
-1
Always disconnect the plug from the socket
.....42000 min -1
before carrying out any work on the machine.
.....19500 min
-1
Accessory - Not included in standard
equipment, available as an accessory.
Do not dispose of electric tools together with
household waste material! In observance of
.............9 m/s 2 European Directive 2002/96/EC on waste
electrical and electronic equipment and its
implementation in accordance with national
law, electric tools that have reached the end
of their life must be collected separately and
returned to an environmentally compatible
recycling facility.
ENGLISH 19