General Safety Rules - REMS Picus S1 Operating Instructions Manual

deu
dienstwerkstatt erbracht werden. Beanstandungen werden nur anerkannt, wenn
das Produkt ohne vorherige Eingriffe in unzerlegtem Zustand einer autorisierten
REMS Vertrags-Kundendienstwerkstatt eingereicht wird. Ersetzte Produkte
und Teile gehen in das Eigentum von REMS über.
Die Kosten für die Hin- und Rückfracht trägt der Verwender.
Die gesetzlichen Rechte des Verwenders, insbesondere seine Mängelansprüche
gegenüber dem Händler, bleiben unberührt. Diese Hersteller-Garantie gilt nur
für Neuprodukte, welche in der Europäischen Union, in Norwegen oder in der
Schweiz gekauft werden.
7. REMS Vertrags-Kundendienstwerkstätten
Firmeneigene Fachwerkstatt für Reparaturen:
SERVICE-CENTER
Neue Rommelshauser Straße 4
D-71332 Waiblingen
Telefon (07151) 56808-60
Telefax (07151) 56808-64
Wir holen Ihre Maschinen und Werkzeuge bei Ihnen ab!
Nutzen Sie in der Bundesrepublik Deutschland unseren Abholservice.
Einfach anrufen unter Telefon (07151) 56808-60.
Oder wenden Sie sich an eine andere autorisierte REMS Vertrags-Kundendienst-
werkstatt in Ihrer Nähe.
Teileverzeichnis
siehe www.rems.de unter Downloads.
Translation of the original operating instructions
Fig. 1 REMS Picus S1 and REMS Simplex
Fig. 2 REMS Picus S3 and REMS Duplex
Fig. 3 REMS Picus S2/3,5 and REMS Duplex 300
Fig. 4 Manually controlled dry boring with tapping tool
Fig. 5 Securing of drill upright with plugs in concrete, with knock-in anchor
Fig. 6 Securing of drill upright with plugs in masonry, with expansion anchor
(anchor sleeve)
Fig. 7 Machine rating plate, REMS Picus S3
Fig. 8 Machine rating plate, REMS Picus S2/3,5
Fig. 9 1) Speed regulation for REMS Picus SR
2) Concrete Ø mm
3) Masonry Ø mm
4) Rotation n ¹/min
5) Gear step
6) Electronic speed regulation
Fig. 1 – 7
1 Boring trestle
2 Feed slider
3 Slotted sleeve
4 Feed lever
5 Adjustment screws
6 Base plate
7 Slot
8 Fillister head screw
9 Turning handle
10 Clamping angle
11 Drive spindle
12 Holder-up
13 Drill collar
14 Cover
15 Water supply system
16 Safety switch, PRCD indicator light
17 Safety switch, PRCD RESET button
18 Safety switch, PRCD TEST button
19 Fault-current safety switch, PRCD
20 Motor handle
21 Switch
22 Adapter
23 Knock-in anchor
24 Flattener
25 Knurled threaded rod
26 Washer
27 Fast-tightening nut

General Safety Rules

WARNING! To reduce the risk of injury, user must read and understand instruc-
tion manual.
WARNING! Read all instructions. Failure to follow all instructions listed below may
result in electric shock, fire and/or serious injury. The term „power tool" in all of the
warnings listed below refers to your mains operated (corded) power tool or battery
operated (cordless) power tool, also machines and electric units. Only use the power
tool for the purpose for which it was intended, with the due attention to the general
safety and accident prevention regulations.
SAVE THESE INSTRUCTIONS.
A) Work area
a) Keep work area clean and well lit. Cluttered and dark areas invite accidents.
b) Do not operate power tools in explosive atmospheres, such as in the pres-
ence of flammable liquids, gases or dust. Power tools create sparks which
may ignite the dust or fumes.
c) Keep children and bystanders away while operating a power tool. Distrac-
tions can cause you to lose control.
B) Electrical safety
a) Power tool plugs must match the outlet. Never modify the plug in any way.
Do not use any adapter plugs with earthed (grounded) power tools. Unmodi-
fied plugs and matching outlets will reduce risk of electric shock. If the power tool
comes with an earthed wire, the plug may only be connected to an earthed
receptacle. At work sites, in damp surroundings, in the open or in the case of
comparable types of use, only operate the power tool off the mains using a 30
mA fault current protected switch (FI breaker).
b) Avoid body contact with earthed or grounded surfaces such as pipes,
radiators, ranges and refrigerators. There is an increased risk of electric shock
if your body is earthed or grounded.
c) Do not expose power tools to rain or wet conditions. Water entering a power
tool will increase the risk of electric shock.
d) Do not abuse the cord. Never use the cord for carrying, pulling or unplug-
ging the power tool. Keep cord away from heat, oil, sharp edges or moving
parts. Damaged or entangled cords increase the risk of electric shock.
e) When operating a power tool outdoors, use an extension cord suitable for
outdoor use. Use of a cord suitable for outdoor use reduces the risk of electric
shock.
eng
28 Expansion anchor
29 Grip head
30 Locknut
33 Threaded spindle
35 Alignment hole
36 Sliding bolt
37 Screws
38 Spacer
39 Handle grip
40 Struts
41 Hose connection
42 Cover plate
43 Sealing ring
44 Water extractor unit
45 Rubber gasket
46 Suction rotor
47 Annular core bit connector,
UNC 1¼ and G ½
48 Diamond core drilling crowns
49 Tapping tool
50 Annular core bit extension
51 Water pressure tank
52 Screws
53 Guide
54 Quick-release ring
55 Whetstone
56 Levelling block
57 Dial