Philips FW-V28 Service Manual page 11

Discs for playback
This system can playback all audio CD,
finalized audio CD-Recorder format discs.
Loading the Disc Changer
1 Press VCD to select VCD/CD mode.
2 Press OPEN•CLOSE.
™ The disc carousel tray slides out.
3 Load a disc with the printed side up in
the right tray.
• You can load another disc in the left
tray.
• To load the third disc, press the DISC
CHANGE button.
™ The disc carousel tray will rotate
until the empty tray is ready for
loading.
™ Playback will always start with the
disc in the inner disc tray.
4 Press OPEN•CLOSE to close the disc
carousel tray.
™ The total number of tracks and the
playing time of the last selected disc
appear on the display.
Note:
– To ensure good system performance,
wait until the disc changer completely
reads the disc(s) before proceeding.
CD - VCD
Programming Tracks
Programming tracks of a loaded disc is
possible when playback is stopped. The
display will indicate the total tracks stored
in the program. Up to 99 tracks can be
stored in the memory in any order. When
99 tracks are stored and you attempt to
store another track, the display will show
"PROGRAM FULL".
Note:
– Program cannot be used for VCDs when
PBC is switched on. Switch off PBC
before storing tracks from such a VCD.
1 Load the desired discs in the disc trays.
2 Press the VCD (CD 1•2•3) button to
select the disc tray.
™ Programming can only be done on the
selected disc.
3 Press PROGRAM to start programming.
™ The PROG flag starts flashing.
™ It will cancel any previously
programmed tracks and selected
repeat mode.
4 Pressí or ë (or digit 0-9 on the
remote control) to select the desired
track.
5 Press PROGRAM to store the track.
• Repeat steps 4 to 5 to store other
tracks.
6 Press Ç once to end programming.
™ The total number of tracks
programmed and total playing time
appear on the display.
14
2-5
Disc Direct Play
You can play a disc directly by pressing the
DISC 1, DISC 2 or DISC 3 button.
Playing a normal disc
For normal VCD:
Ensure that the system is switched to
the corresponding PAL or NTSC
system of your TV set (except multi-
system TV).
1 Press PLAYÉ Å to start playback.
™ The disc tray, track number and
elapsed playing time of the current
track appear on the display.
• To interrupt playback, press PAUSE
É Å .
™ The playing time flashes.
• To resume playback, press PLAYÉ Å
again.
2 To stop playback, press Ç.
Note:
– During Disc Reading mode, if you press
any button, " PLEASE WAIT " will be
displayed.
Notes:
– If the total playing time is more than
" 99:59 " then " -- : -- " appears on the
display instead of the total playing time.
– During programming, if no button is
pressed within 20 seconds, the system
will exit program mode automatically.
Reviewing the program
Reviewing of program is possible only
when playback is stopped.
1 Press í or ë repeatedly to review
the programmed tracks.
2 Press Ç to exit review mode.
Playing the program
1 Press PLAY É Å to start program
playback.
™ "PLAY PROGRAM" will be
displayed.
™ The track number and elapsed
playing time of the current track will
appear on the display.
™ The PROG flags appear on the
display.
2 Press Ç to stop program playback.
Note:
– If you press any other CD DIRECT PLAY
buttons, the system will play the
selected disc or track and the stored
program will be cleared.
Disc Change
You can change the outer two discs while
the third inner disc is stopped or is playing.
1 Press DISC CHANGE.
™ The disc carousel tray slides out.
2 Replace the discs in the left and right
disc trays.
• If you press DISC CHANGE again
during playback, the disc will stop
playing.
™ The disc carousel tray will rotate
until the inner tray is rotated out and
is ready for changing.
3 Press OPEN•CLOSE to close the disc
carousel tray.
Selecting a desired track
Selecting a desired track when
playback is stopped
• Press digit 0 – 9 on the remote control
to select the desired track.
™ Playback will start immediately for
the selected track.
™ The selected track number and
elapsed playing time appear on the
display.
Erasing the program
(when
playback is stopped)
• Press Ç.
™ "PROGRAM CLEARED" will be
displayed.
Note:
– The program will be erased when the
system is disconnected from the power
supply, the system is switched to
standby mode, when you change source
or when you change the program disc.
CD - VCD
Selecting a desired track during
playback
• Press í or ë (or digit 0-9 on the
remote control) until the desired track
appears on the display.
™ The selected track number and
elapsed playing time appear on the
display.
• If you press í once it will skip to the
beginning of the previous track and play
the track.
Searching for a particular
passage during playback
• Press à or á to select 4 different
search speed.
™ "FRX1" ; "FRX2" ; "FRX3" or
"FRX4" is displayed on the TV
screen when you select a fast rewind
search.
™ "FFX1" ; "FFX2" ; "FFX3" or
"FFX4" is displayed on the TV
screen when you select a fast
forward search.
™ Normal playback will begin at the
end of the fast rewinding or
forwarding of the selected track.
• Play returns to normal when PLAYÉ Å
is pressed or when a new track is
selected.
VIDEO CD
Adjusting the TV System
Before viewing the Video CD, ensure that
the set is switched to corresponding PAL or
NTSC system of your TV set (exception
Multi-system TV) .
• Press and hold PAL/NTSC for more
than 2 seconds to switch between PAL
or NTSC TV system.
™ After TV system is selected, the set
will automatically switch to the last
TV system setting everytime the VCD
source is selected.
OSD - On Screen Display
If you insert one or more VCDs/CDs, your
TV screen will serve as an additional
display for messages (e.g. PLAY, STOP), and
information stored on the VCD/CD.
• Press OSD on the remote control
repeatedly to switch ON or OFF.
When OSD is switched ON; you can see
the following display on the TV screen.
PCS 103 731
13