Service; Description; Installation - Philips Dinion LTC 0435 Series Installation Instructions Manual

SAFETY PRECAUTIONS
The exclamation point within an equilateral triangle is
intended to alert the user to presence of important
operating and maintenance (servicing) instructions in
the literature accompanying the appliance.
SECURITE
Le point d'exclamation à l'intérieur d'un triangle
équilatéral avertit l'utilisateur de la présence d'instruc-
tions importantes d'utilisation et de maintenance dans
la documentation accompagnant l'appareil.
SICHERHEITSVORKENHRUNGEN
Das Ausrufezeichen in dem gleichseitigen Dreieck ist
dazu da, den Benutzer auf wich-tige Inbetriebnahme-
und Instandhaltungs-vorschriften hinzuweisen, die
dem Gerät in Form einer Broschüre beigelegt sind.
PRECAUCIONES DE SEGURIDAD
El símbolo de exclamación dentro de un triángulo
equilátero, se muestra con el objetivo de alertar al
ususario de que instrucciones de operación y manten-
imiento importantes acompañan al equipo.
1 UNPACKING
Unpack carefully. This is mechanical equipment and should be
handled with care.
Check for the following items:
Verify the unit model number.
I
Instructions for Use.
I
If an item appears to have been damaged in shipment, replace it
properly in its carton and notify the shipper. If any items are
missing, notify your Philips Communication, Security &
Imaging, Inc. Sales Representative or Customer Service
Representative. The shipping carton is the safest container in
which the unit may be transported. Save it for possible future use.
2

SERVICE

If the unit ever needs repair service, the customer should contact
the nearest Philips Communication, Security & Imaging, Inc.
Service Center for authorization to return and shipping
instructions.
Service Centers
U.S.A. & Canada: 800-366-2283
Mexico & Central America: 52-5-564-2726
Europe & Middle East: 011-32-1-440-0711
South America: 54-11-4956-0837
Asia Pacific Region: 011-65-481-4422
3

DESCRIPTION

LTC 9215/00 30-cm (12-in), LTC 9215/00S 18-cm (7-in),
and LTC 9219/01 40-cm (15-in) Feed-through Mounts.
This indoor/outdoor mounting equipment is designed for fixed
camera or camera housing installations up to 9 kg (20 lb) rated
load. These models are made of lightweight aluminum and fea-
ture welded construction, providing an extremely rigid camera
mount. The LTC 9215/00S has been designed specifically for
the LTC 9480 series housings, while the LTC 9215/00 and LTC
9219/01 can be used with the LTC 9480, LTC 9483, and LTC
9488 series camera housings. All mounts come fully assembled.
4

INSTALLATION

1. Determine a secure wall mounting location.
WARNING: All mounts are designed to support a
load only in a vertical direction. Mounts MUST be posi-
tioned as shown under SPECIFICATIONS.
2. Cautions:
a. For a secure installation, use four 8-mm (5/16-in) diam-
eter fasteners (not included). Use stainless steel or zinc
plated fasteners.
b. If bolts are used, they should extend through the mount-
ing surface and be secured with flat washers, lock wash-
ers, and nuts on the opposite side. Each bolt must have
a minimum pull-out strength of 200 kg (450 lb).
c. If studs are used, they should be anchored in concrete or
welded to a steel backer plate. Each stud must have a
minimum pull out strength of 200 kg (450 lb).
d. If the wall mount is attached to wood or to a blind
structure (with no access to the rear), each fastener must
have a minimum pull-out strength of at least 200 kg
(450 lb).
3. Locate the four holes or stud locations using the flange as a
template (four holes equally spaced on a 69.9-mm (2-3/4-in
bolt circle).
4. Feed wires through the large hole in the flange or through
the slot on the surface where the camera housing mounts.
5. Install the mount using bolts or studs at least 8-mm (5/16-
in) in diameter.
6. To mount the camera or camera housing:
a. Mount camera with a 1/4-20 bolt and lock washer (not
furnished) in the center hole of the adjustable head.
b. Mount housings with three 1/4-20 bolts and lock
washers (not furnished).
c. Lock mount head in position by using the supplied
1/8-inch long-arm hex wrench to tighten screws.
For additional information or to speak to a representative,
please contact the Philips Communication, Security &
Imaging location nearest you:
The Americas: 1 800 326 3270
Europe & Middle East: 31 40 278 1222
Asia Pacific Region: 65 350 1859
or visit our Web site at www.philipscsi.com.
2