Table of Contents
Advertisement
Quick Links
Download this manual
See also:
Instruction Manual
Electric Fireplace
Electric Fireplace
Wall Mount
Mount & Recessed Instruction
Electric Fireplace Packing List
Electric Fireplace Packing List
1
1
1
2
1
1
1
Yosemite Home Décor
www.YosemiteHomeDecor.com
www.YosemiteHomeDecor.com
Electric Fireplace
Glass Face
Remote Control
AAA Batteries
Instruction Manual
Wall Fixing Plate
Fastener Package
1-800-305-9872
Instruction
Advertisement
Table of Contents
Related Manuals for Yosemite DF-EFP148
Summary of Contents for Yosemite DF-EFP148
- Page 1 Electric Fireplace Electric Fireplace Wall Mount Mount & Recessed Instruction Instruction Electric Fireplace Packing List Electric Fireplace Packing List Electric Fireplace Glass Face Remote Control AAA Batteries Instruction Manual Wall Fixing Plate Fastener Package Yosemite Home Décor 1-800-305-9872 www.YosemiteHomeDecor.com www.YosemiteHomeDecor.com...
-
Page 2: Installation Instructions
5. The fireplace must not be installed in an area where there is restricted air flow around the unit. 6. Yosemite fireplaces are approved for indoor use only. 7. The fireplace must be kept away from any source of damp or moist conditions. Avoid any close contact with water. -
Page 3: Drywall Installation
Fireplace Installation – Wall Mount Figure 1 1. Select the position of the fireplace on the wall to which it is to be mounted. Draw a level horizontal line on the wall at the required height. This line will correspond to the top of the fireplace so it is important to allow for the extra height of the glass face. - Page 4 8. Lift the fireplace and place the keyhole slots situated on the back of the fire (Figure 2) to the location pins on the mounting plate. A gentle application of downward pressure will lock it into place. Make sure all of the pins have been located into the top section of each keyhole fixing slot.
- Page 5 13. The fireplace must not be modified in any way or used for purpose other than those recommended by Yosemite Home Decor. 14. If the fireplace shows any signs of damage it is important that it is examined by a qualified professional before use is continued.
-
Page 6: Technical Specifications
TECHNICAL SPECIFICATIONS MODEL NUMBER DF-EFP1313NH VOLTS AMPS 94 ¾” NO HEATER 365 watts ¼” 9 Candelabra Incandescent QUANTITY LAMPS 40 watts WATTS TOTAL WATTS 360 watts ROTOR MOTOR 1 at 5 watts 78 ½” 10 ½” 26 ½” DIMENSION 94 ¾” W x 26 ½” H x 7” D 19”... - Page 7 Fireplace Installation – Recess CAUTION Two people may be needed to perform this installation 1. Prepare a frame opening according to the dimension of the fire unit. Kindly refer to the chart. Figure 6 FRAME OPENING WALL HANG Width Height Depth DF-EFP1313NH 81 ¼"...
- Page 8 P a g e...
-
Page 9: Attaching The Face
Attaching the Face Two people may be required to carry out this installation 1. On each side of the fireplace are two locating studs (Figure 5). 2. On the back of the face there are two brackets which hook over these studs. 3. -
Page 10: Side View
Side View P a g e... - Page 11 OPERATING INSTRUCTIONS CAUTIONS: 1. When the fireplace is in operation certain areas of the fireplace surface will get hot. Caution must be taken to avoid being burned. Take care not to touch hot surfaces. 2. The fireplace must not be switched on if volatile vapors are present in the room 3.
- Page 12 Fireplace Control Panel The control panel is located on the right hand side of the fireplace (Figure 7). Main Power Switch On/Off Switch Flame Effect Dimmer Switch Heater Maximum Heat 1500 W Heater Low Heat 750 W 11 | P a g e...
-
Page 13: Remote Control
Remote Control DIMMER ON/OFF HIGH HIGH\LO W Infrared Window On/Off Switch Flame Effect Dimmer Heater Maximum Heat Heater Low Heat 1. Prior to use, the remote control handset requires installation of Prior to use, the remote control handset requires installation of the two included the two included AAA batteries (Figure 8). - Page 14 Heater Maximum Heat (1500 W) Press this once to switch to high heat. The indicator light will come on as well as the fan. Press again to turn off. (The fan will continue to run for a few moments until sensors indicate cool condition) Heater Low Heat (750 W) Press this once to switch to high heat.
-
Page 15: Maintenance Instructions
MAINTENANCE INSTRUCTIONS Changing Light Bulbs Disconnect power supply before beginning any maintenance. 1. Light bulbs need to be replaced when you notice a dark section of the flame or when clarity and detail of the coal effect disappears. 2. Unscrew the locking nut on the side of the brackets and then remove the face. This is done by lifting the face up and swinging the face clear of the fire.