Step 4: Connecting The Mains Lead; Step 5: Preparing The Remote - Sony RDR-HX520 Service Manual

QQ
3 7 63 1515 0
b
Notes
• Do not connect your TV's audio output jacks to
the LINE IN (R-AUDIO-L) jacks at the same
time. This will cause unwanted noise to come
from your TV's speakers.
• With connection B, do not connect the LINE IN
(R-AUDIO-L) and LINE 2 OUT (R-AUDIO-L)
jacks to your TV's audio output jacks at the same
time. This will cause unwanted noise to come
from your TV's speakers.
• With connection A, after you have completed the
connection, make the appropriate settings under
"Easy Setup - Audio Connection" (page 20).
Otherwise, no sound or a loud noise will come
from your speakers.
*1
Manufactured under license from Dolby
Laboratories.
"Dolby" and the double-D symbol are
trademarks of Dolby Laboratories.
*2
"DTS" and "DTS Digital Out" are trademarks of
Digital Theater Systems, Inc.
TE
L 13942296513
16
2
With the TV [/1 button pressed down,
enter the TV's manufacturer code
using the number buttons.
For instance, to enter "09," press "0" then
"9." After you enter the last number,
release the TV [/1 button.
Code numbers of controllable TVs
If more than one code number is listed,
try entering them one at a time until you
find the one that works with your TV.
Manufacturer Code number
Sony 01 (default)
Hitachi 24
JVC 33
Panasonic 17, 49
Philips 06, 08
Samsung 71
Sanyo 25
Thomson 43
Toshiba 38
The remote performs the following:
Buttons Operations
TV [/1
Turns your TV on or
off
TV 2 (volume)
Adjusts the volume
+/– of your TV
TV PROG +/– Selects the
programme position
on your TV
TV t
Switches your TV's
input source
To operate the TV/DVD button
(for SCART connections only)
The TV/DVD button switches between the
www
recorder and the last input source selected on
the TV. Point your remote at the recorder
when using this button.
When you connect the recorder to the TV via
the SCART jacks, the input source for the TV
is set to the recorder automatically when you
start playback. To watch another source,
.
press the TV/DVD button to switch the TV's
input source.
18
http://www.xiaoyu163.com
Step 4: Connecting the
Mains Lead
Connect the supplied mains lead to the AC IN
terminal of the recorder. Then plug the
recorder and TV mains leads (power cords)
into the mains. After you connect the mains
lead, you must wait for a short while
before operating the recorder. You can
operate the recorder once the front panel
display lights up and the recorder enters
standby mode.
If you connect additional equipment to this
recorder (page 21), be sure to connect the
mains lead after all connections are complete.
~
AC IN
1
to AC IN
2
to mains
If you have a Sony DVD player
or more than one Sony DVD
recorder
If the supplied remote interferes with your
other Sony DVD recorder or player, set the
command mode number for this recorder and
the supplied remote to one that differs from
the other Sony DVD recorder or player after
you have completed "Step 6: Easy Setup."
The default command mode setting for this
recorder and the supplied remote is DVD3.
Number
buttons
SYSTEM
MENU
M/m,
ENTER
1
Check that "Easy Setup" (page 20)
has been finished. If "Easy Setup" has
not been finished, first perform "Easy
Setup."
2
Press SYSTEM MENU.
The System Menu appears.
3
Select "SETUP," and press ENTER.
x ao u163
y
i
http://www.xiaoyu163.com
2 9
8
Step 5: Preparing the
Remote
You can control the recorder using the
supplied remote. Insert two R6 (size AA)
batteries by matching the 3 and # ends on
the batteries to the markings inside the
battery compartment. When using the
remote, point it at the remote sensor on the
recorder.
b
Notes
• If the supplied remote interferes your other Sony
DVD recorder or player, change the command
mode number for this recorder (page 18).
• Use the batteries correctly to avoid possible
leakage and corrosion. Should leakage occur, do
not touch the liquid with bare hands. Observe the
following:
– Do not use a new battery with an old battery, or
batteries of different manufacturers.
– Do not attempt to recharge the batteries.
– If you do not intend to use the remote for an
extended period of time, remove the batteries.
– If battery leakage occurs, wipe out any liquid
inside the battery compartment, and insert new
batteries.
• Do not expose the remote sensor (marked on
the front panel) to strong light, such as direct
sunlight or a lighting apparatus. The recorder may
not respond to the remote.
Q Q
3 6 7 1 3 1 5
4
Select "Others," and press ENTER.
5
Select "Command Mode," and press
ENTER.
6
Select a Command Mode (DVD1,
DVD2, or DVD3), and press ENTER.
7
Set the Command Mode for the remote
so it matches the Command Mode for
the recorder you set above.
Follow the steps below to set the
Command Mode on the remote.
1 Hold down ENTER.
2 While holding down ENTER, enter
the Command Mode code number
using the number buttons.
Command Mode Code number
DVD1 number button 1
DVD2 number button 2
DVD3 number button 3
3 Hold down both the number and
ENTER buttons at the same time for
more than three seconds.
To check the Command Mode for the
recorder
Press x on the recorder when the recorder is
co
turned off. The Command Mode for the
recorder appears in the front panel display.
.
1-4
9 4 2 8
Controlling TVs with the
remote
You can adjust the remote's signal to control
your TV.
b
Notes
• Depending on the connected unit, you may not be
able to control your TV with some or all of the
buttons below.
• If you enter a new code number, the code number
previously entered will be erased.
• When you replace the batteries of the remote, the
code number may be reset to the default setting.
Set the appropriate code number again.
Number
buttons
TV/DVD
TV [/1
TV 2 +/–
TV t
TV PROG
+/–
1
Hold down the TV [/1 button located
at the bottom of the remote.
Do not press the [/1 button at the top of
the remote.
0 5 8 2 9 9 4 2 8
,continued
17
If the Command Mode for the recorder has
not been changed, set the Command Mode
for the remote to the default setting of
DVD3. If the Command Mode for the
remote is changed to DVD1 or DVD2, you
will be unable to operate this recorder.
Changing programme positions
of the recorder using the
remote
You can change programme positions of the
recorder using the number buttons.
Number
buttons
ENTER
Example: for channel 50
Press "5," "0," then press ENTER.
m
19
9 9
9 9