Video Settings (Video); Audio Settings (Audio) - Sony RDR-HX520 Service Manual

QQ
3 7 63 1515 0

Video Settings (Video)

Video settings will adjust items related to the
image, such as size and colour.
Choose the settings according to the type of
TV, tuner, or decoder connected to the DVD
recorder.
1
Press SYSTEM MENU while the
recorder is in stop mode.
2
Select "SETUP," and press ENTER.
3
Select "Video," and press ENTER.
The "Video" setup appears with the
following options. The default settings
are underlined.
Video Output
TV Type
Sets the picture size when playing back a title
recorded from 16:9 size video (page 46) or a
16:9 size commercial DVD video.
Select the playback picture size according to
the type of connected TV (wide-screen/wide
mode TV or conventional 4:3 screen TV).
16:9 Select this when connecting
to a wide-screen TV or TV
with a wide mode function.
4:3 Letter Select this when connecting
Box to a 4:3 screen TV. Displays a
wide picture with bands on
the upper and lower portions
of the screen.
4:3 Pan Select this when connecting
Scan to a 4:3 screen TV.
Automatically displays a
wide picture on the entire
screen and cuts off the
portions that do not fit.
TE
L 13942296513
88
Colour System
Selects the colour system when playing
VIDEO CDs (including Super VIDEO CDs)/
DivX video files.
PAL
Plays a disc in PAL colour
system.
NTSC
Plays a disc in NTSC colour
system.
Auto Display
On Automatically displays
information on the screen
when the recorder is turned
on, etc.
Off Displays information only
when DISPLAY is pressed.
Screen Saver
The screen saver image appears when you do
not use the recorder for more than 10 minutes
while an on-screen display, such as the
System Menu, is displayed on your TV
screen. The screen saver image helps prevent
your display device from becoming damaged
(ghosting).
On
Turns on the screen saver
function.
Off Turns off the function.
www
.
90
http://www.xiaoyu163.com
16:9
4:3 Letter Box
4:3 Pan Scan
b
Note
Depending on the disc, "4:3 Letter Box" may be
selected automatically instead of "4:3 Pan Scan" or
vice versa.
Component Out
Selects whether or not to output video signals
from the COMPONENT VIDEO OUT jacks.
On Outputs the component video
signals. Select this when you
want to view progressive
signals.
Off Outputs no signals.
b
Notes
• When you set "Line1 Output" to "RGB," you
cannot set "Component Out" to "On."
• When you connect the recorder to a monitor or
projector via only the COMPONENT VIDEO
OUT jacks, do not select "Off." If you select
"Off" in this case, the picture may not appear.
Progressive Output
If your TV accepts progressive (525p/625p)
format signals, set "Progressive Output" to
"On." You will enjoy accurate colour
reproduction and high quality images.
1
Select "Progressive Output," and press
ENTER.
2
Select "On," and press ENTER.
The display asks for confirmation.
3
Select "Start," and press ENTER.
The video switches to a progressive
signal for 5 seconds.
4
If video signal appears OK, select "Yes,"
and press ENTER.
If picture is distorted, select "No," and
press ENTER.

Audio Settings (Audio)

The "Audio" setup allows you to adjust the
sound according to the playback and
connection conditions.
1
Press SYSTEM MENU while the
recorder is in stop mode.
2
Select "SETUP," and press ENTER.
3
Select "Audio," and press ENTER.
The "Audio" setup appears with the
following options. The default settings
are underlined.
Audio ATT (attenuation)
If the playback sound is distorted, set this
item to "On." The recorder reduces the audio
output level.
This function affects the output of the
following jacks:
– LINE 2 OUT R-AUDIO-L jacks
– LINE 1 – TV jack
– LINE 3/DECODER jack
On Select this when the playback
sound from the speakers is
distorted.
Off
Normally select this position.
x ao u163
y
i
http://www.xiaoyu163.com
2 9
8
Progressive Mode
DVD software can be divided into two types:
film based software and video based
software. Video based software is derived
from TV and displays images at 25 frames/50
fields (30 frames/60 fields) per second. Film
based software is derived from film and
displays images at 24 frames per second.
Some DVD software contains both Video
and Film.
In order for these images to appear natural on
your screen when output in progressive mode
(50 or 60 frames per second), the progressive
video signal needs to be converted to match
the type of DVD software that you are
watching.
You can fine-tune the progressive 525p/625p
video signal that is output when you set
"Progressive Output" to "On."
Note that you must connect to a progressive
format TV using the COMPONENT VIDEO
OUT jacks (page 13).
Auto
Automatically detects the
software type (Film-based or
Video-based) and selects the
appropriate conversion mode.
Normally select this position.
Video Fixes the conversion mode to
the mode for Video-based
software.
b
Note
When picture noise appears after you set the
recorder to progressive format, hold down x, and
press PROGRAM – (minus) on the unit.
Scart Setting
Sets the method of inputting/outputting
signals from the SCART jacks on the rear
panel of the recorder. Select an option for
each of the items below according to the
combination of jacks and methods that you
are going to use.
Line1 Output
Selects a method of outputting video signals
for the LINE 1 – TV jack.
RGB Outputs RGB signals.
Video Outputs video signals.
S Video Outputs S-video signals.
Q Q
3 6 7 1 3
Audio Connection
The following setup items switch the method
of outputting audio signals when you connect
a component such as an amplifier (receiver)
with a digital input jack.
For connection details, see "Step 3:
Connecting the Audio Cords" on page 15.
Select "Dolby Digital," "MPEG," "DTS,"
and "48kHz/96kHz PCM" after setting
"Digital Out" to "On."
If you connect a component that does not
accept the selected audio signal, a loud noise
(or no sound) will come out from the
speakers, and may affect your ears or cause
speaker damage.
1
Select "Audio Connection" in "Audio,"
and press ENTER.
2
Select "Digital Out," and press ENTER.
On
Normally select this
position.
Off The influence of the
digital circuit upon the
analogue circuit is
minimal.
3
Select "On," and press ENTER.
4
Set the digital output signal.
• Dolby Digital (HDD/DVDs only)
Selects the type of Dolby Digital signal.
D-PCM Select this when the recorder
is connected to an audio
component lacking a built-in
Dolby Digital decoder. The
surround effects of output
signals are determined by the
"Downmix" setting item in
the "Audio" setup.
Dolby Select this when the recorder
Digital is connected to an audio
.
component with a built-in
Dolby Digital decoder.
1-22
9 4 2 8
b
Notes
• If your TV does not accept S-video or RGB
signals, no picture appears on the TV screen even
if you select "S Video" or "RGB." See the
instructions supplied with your TV.
• You cannot select "RGB" when "Component
Out" above is set to "On."
• SMARTLINK is available only when "Video" is
selected.
Line3 Input
Selects a method of inputting video signals
for the LINE 3/DECODER jack. The picture
will not be clear if this setting does not match
the type of video input signal.
Video/ Inputs video signals or RGB
RGB
signals.
Decoder Select this when connecting
to a PAY-TV/Canal Plus
analogue decoder. If you
connect to a cable box/
satellite receiver such as
CanalSat, do not select this
option.
S Video Inputs S-video signals.
b
Note
Input signals are recorded in video mode when
"Video/RGB" is selected (only French RDR-
HX520 and RDR-HX920 models can record in
video or RGB).
Line3 Output
Selects a method of outputting video signals
for the LINE 3/DECODER jack.
Video Outputs video signals.
S Video
Outputs S-video signals.
Pause Mode (HDD/DVDs only)
Selects the picture quality in pause mode.
Auto The picture, including
subjects that move
dynamically, is output with
no jitter. Normally select this
position.
Frame The picture, including
subjects that do not move
dynamically, is output in high
resolution.
1 5 0 5 8 2 9 9 4
,continued
89
• MPEG (DVD VIDEOs only)
Selects the type of MPEG audio signal.
PCM
Select this when the recorder
is connected to an audio
component without a built-in
MPEG decoder. If you play
MPEG audio sound tracks,
the recorder outputs stereo
signals via the DIGITAL
OUT (COAXIAL) jack.
MPEG Select this when the recorder
is connected to an audio
component with a built-in
MPEG decoder.
• DTS (DVD VIDEOs only)
Selects whether or not to output DTS signals.
On Select this when the recorder
is connected to an audio
component with a built-in
DTS decoder.
Off Select this when the recorder
is connected to an audio
component without a built-in
DTS decoder.
• 48kHz/96kHz PCM (DVD VIDEOs only)
Selects the sampling frequency of the audio
signal.
48kHz/
The audio signals of DVD
16bit VIDEOs are converted to 48
kHz/16 bit and output.
96kHz/ All signals containing
24bit 96 kHz/24 bit are output
without conversion.
However, the signals are
output at 48 kHz/16 bit if
copyright-protected signals
are contained.
b
Note
"48kHz/96kHz PCM" setting has no effect when
m
audio signals are output from the LINE 2 OUT (R-
AUDIO-L) jacks or LINE 1 – TV/LINE 3/
DECODER jack. If the sampling frequency is
96kHz, signals are simply converted to analogue
co
signals and output.
,continued
91
9 9
2 8 9 9