Connections - Denon avr-2105 Operating Instructions Manual

5

CONNECTIONS

Connecting the audio components
• When making connections, also refer to the operating instructions of the other components.
CD player
OUTPUT
R L
DIGITAL AUDIO DIGITAL AUDIO
R L
Connecting a Turntable
Connect the turntable's output cord to the AVR-2105's PHONO jacks,
the L (left) plug to the L jack, the R (right) plug to the right jack.
NOTES:
• This unit cannot be used with MC cartridges directly. Use a
separate head amplifier or step-up transformer.
• If humming or other noise is generated when the ground wire is
connected, disconnect the ground wire.
Turntable
(MM cartridge)
Ground wire
MD recorder, CD recorder or
other component equipped with
digital input/output jack
B
OUTPUT INPUT
OPTICAL
DIGITAL AUDIO DIGITAL AUDIO
COAXIAL OPTICAL
OUTPUT
CD player or other component
equipped with digital output jacks
Connecting the DIGITAL jacks
Use these for connections to audio (video) equipment with digital output.
Refer to page 17 for instructions on setting this terminal.
NOTES:
• Use 75 Ω/ohms cable pin cords for coaxial connections.
• Use optical cables for optical connections, removing the cap before
connecting.
• The main unit's power must be turned on when recording via the AVR-
2105.
Connecting a CD player
Connect the CD player's analog output
jacks (ANALOG OUTPUT) to this unit's CD
jacks using pin plug cords.
Connecting the PRE OUT jacks
Use these jacks if you wish to connect external power amplifier(s)
to increase the power of the front, center and surround sound
channels, or for connection to powered loudspeakers.
To use Surround back with one speaker, connect the speaker to
SURR. BACK L CH.
R
R L R L
L
R
L
Route the connection cords, etc., in
such a way that they do not obstruct
the ventilation holes.
R L R L
B
R L R L
INPUT OUTPUT
CD recorder or Tape deck
Connecting a tape deck
Connections for recording:
Connect the tape deck's recording input jacks (LINE IN or REC) to this unit's
tape recording (CDR/TAPE OUT) jacks using pin plug cords.
Connections for playback:
Connect the tape deck's playback output jacks (LINE OUT or PB) to this unit's
tape playback (CDR/TAPE IN) jacks using pin plug cords.
NOTE:
If humming noise is generated by a tape deck, etc., move the tape deck
away.
• Do not plug in the AC cord until all connections
have been completed.
• Be sure to connect the left and right channels
properly (left with left, right with right).
• Insert the plugs securely. Incomplete connections
will result in the generation of noise.
• Use the AC OUTLET for audio equipment only.
Do not use them for hair driers, etc.
Power supply cord
AC 230V, 50Hz (ASIA model)
AC 220V, 50Hz (CHINA model)
AC 120V, 60Hz (TAIWAN R.O.C. model)
SWITCHED TOTAL 120W MAX.
SWITCHED 100W MAX.
AC 120V 60Hz
AC OUTLETS AC OUTLET
for Taiwan R.O.C. model for Asia model
• Note that binding pin plug cords together with AC
cords or placing them near a power transformer
will result in generating hum or other noise.
• Noise or humming may be generated if a
connected audio equipment is used independently
without turning the power of this unit on. If this
happens, turn on the power of the this unit.
Connecting the AC OUTLTETS
AC OUTLET
• SWITCHED
(total capacity – 120 W – for Taiwan R.O.C. model)
(total capacity – 100 W – for Asia model)
The power to these outlets is turned on and off in conjunction with the
POWER operation switch on the main unit, and when the power is
switched between on and standby from the remote control unit.
No power is supplied from these outlets when this unit's power is at
standby. Never connect equipment whose total capacity is above 120 W
for Taiwan R.O.C. model (100 W for Asia model).
NOTE:
Only use the AC OUTLET for audio equipment. Never use them for hair
driers, TVs or other electrical appliances.
ENGLISH
5