Page 1
HCD-GNX600 SERVICE MANUAL E Model Australian Model Ver. 1.1 2006.10 • HCD-GNX600 is the Amplifier, CD player, tape deck and tuner section in MHC-GNX600. Model Name Using Similar Mechanism HCD-GNX800 CD Mechanism Type CDM74KFS-F1BD81A Section Base Unit Name BU-F1BD81A Optical Pick-up Name...
Page 2
COMPONENTS IDENTIFIED BY MARK 0 OR DOTTED LINE WITH MARK 0 ON THE SCHEMATIC DIAGRAMS AND IN THE PARTS LIST ARE CRITICAL TO SAFE OPERATION. REPLACE THESE COMPONENTS WITH SONY PARTS WHOSE PART NUMBERS APPEAR AS SHOWN IN THIS MANUAL OR IN SUPPLEMENTS PUBLISHED BY SONY.
HCD-GNX600 SECTION 1 SERVICING NOTES • MODEL IDENTIFICATION NOTES ON HANDLING THE OPTICAL PICK-UP BLOCK – Back Panel – OR BASE UNIT The laser diode in the optical pick-up block may suffer electrostatic break-down because of the potential difference generated by the charged electrostatic load, etc.
HCD-GNX600 SECTION 2 GENERAL This section is extracted from instruction manual. LOCATING THE CONTROLS ALPHABETICAL ORDER SYMBOLS MASTER VOLUME ws ?/1 (power) ef Z OPEN/CLOSE q; ALBUM + qk MIC 1/2 (jack) wf N (play) qd ALBUM – ql . OPERATION DIAL >...
HCD-GNX600 This section is extracted from instruction manual. Remote control TAPE wd ALPHABETICAL ORDER TUNER/BAND 7 TUNER MEMORY wg A – E TUNING MODE 5 ALBUM + qf VOLUME +/– qg ALBUM – qh CD wf The + button has a tactile dot.*...
HCD-GNX600 SECTION 3 DISASSEMBLY • This set can be disassembled in the order shown below. 3-1. DISASSEMBLY FLOW 3-2.SIDE CASE, TOP CASE (Page 8) 3-3.LOADING PANEL (Page 8) 3-4.FRONT PANEL ASSY (Page 9) 3-7.PANEL BOARD, 3-6.TAPE MECHANISM DECK, 3-5.TUNER PACK...
HCD-GNX600 Note: Follow the disassembly procedure in the numerical order given. 3-2. SIDE CASE, TOP CASE qf case (top) qs two screws 7 screw (+BVTP 3 × 8) (case 3 TP2) (3 × 12) 8 screw (+BVTP 3 × 8)
HCD-GNX600 3-16. MOTOR (TB) BOARD 2 stopper 1 stopper 7 t able motor assy (M741) 3 wire (flat type) 5 core (CN742) 8 MOTOR (TB) board 6 Remove the two solderings of motor. 5 two screws (+BTTP (M2.6)) 3-17. MOTOR (LD) BOARD 2 two screws (+BTTP (M2.6))
HCD-GNX600 SECTION 4 TEST MODE [PANEL TEST MODE] • This mode is used to check the fluorescent indicator tube, [COMMON TEST MODE] LEDs, buttons, MASTER VOLUME knob, model, • This mode is used to check operations of the respective sections destination, software version and VACS level.
Page 17
HCD-GNX600 [CD AGING MODE] [VACS ON/OFF] This mode can be used for operation check of CD section. • This mode is used to switch ON and OFF the VACS (Variable • If an error occurs, the aging operation would stops and the Attenuation Control System).
Page 18
HCD-GNX600 • Display when an error occurred (CD Error Code Mode) Procedure: 3) Display of no disc errors Display 1. Press x button, [ILLUMINATION/SUB WOOFER LEVEL] button and [DISC 1] button simultaneously to D*$$%%&&##00 enter the error code display mode.
Page 19
HCD-GNX600 [CD SHIP MODE (WITHOUT MEMORY CLEAR)] [CD TRAY LOCK MODE] • This mode moves the optical pick-up to the position durable • This mode let you lock the disc tray. When this mode is to vibration. Use this mode when returning the set to the...
HCD-GNX600 SECTION 5 SECTION 6 MECHANICAL ADJUSTMENTS ELECTRICAL ADJUSTMENTS Precaution DECK SECTION 0 dB=0.775 V 1. Clean the following parts with a denatured alcohol-moistened swab: 1. Demagnetize the record/playback head with a head record/playback heads pinch rollers demagnetizer. erase head rubber belts 2.
HCD-GNX600 2. Turn the adjustment screw and check output peaks. If the peaks CD SECTION do not match for L-CH and R-CH, turn the adjustment screw so that outputs match within 1dB of peak. Note: 1. CD Block is basically designed to operate without adjustment.
Page 22
HCD-GNX600 RFAC Level Check E-F Balance Check Connection: Connection: oscilloscope oscilloscope CD board CD board JPO103 (TE1) TP124 (RFAC) TP117 (VC) – TP117 (VC) – Procedure: Procedure: 1. Connect an oscilloscope to test point TP124 (RFAC) and TP 1. Connect an oscilloscpe to test point TPO103 (TE1) and TP117 117(VC) on the CD board.
Page 23
HCD-GNX600 Checking Location: – CD BOARD (SIDE B) – TP117 (VC) JPO103 (TE1) IC101 JPO102 (FE1) TP124 (RFAC)
HCD-GNX600 SECTION 7 DIAGRAMS Note on Printed Wiring Boards: For schematic diagrams. Note: • All capacitors are in µF unless otherwise noted. (p: pF) Note: • X : parts extracted from the component side. 50 V or less are not indicated except for electrolytics and •...
Page 25
HCD-GNX600 • WAVEFORMS • CIRCUIT BOARDS LOCATION – CD BOARD – – MAIN BOARD – – SMASTER BOARD – IC101 wa IC401 qa IC800 2 XC-OUT SENSOR board 0.8 Vp-p CD board 2.7 Vp-p SW board 0.15 Vp-p MOTOR (LD) board TUNER pack 20.3 nsec...
HCD-GNX600 7-3. BLOCK DIAGRAM – MAIN SECTION – IC1400 DIGTAL ECHO AD IN DA OUT IC1401 ECHO MIC AMP MIC VOL J1450(1/3) MC1P POOUT MIC OUT ADPCM ADPCM POST DELAY MIC 2 ENCODE DECODE J1400(3/3) J1400(1/3) MC2P MIC 1 VOLUME...
HCD-GNX600 7-7. SCHEMATIC DIAGRAM – CD BOARD – • See page 51 and 52 for IC Block Diagrams. • See page 25 for Waveforms. • See page 54 for IC Pin Function Description CN101 R307 C125 C134 C307 TP304 C151...
HCD-GNX600 Ver. 1.1 • See page 25 for Waveforms. • See page 57 for IC Pin Function Description 7-12. SCHEMATIC DIAGRAM – MAIN BOARD (2/3) – HCD-GNX600...
HCD-GNX600 7-26. IC Pin Function Descriptions • IC101 CXD3059AR (RF AMP,DSP,DAC) (CD BOARD) Pin No. Pin Name Description MIRR Not used (Open) DFCT Not used (Open) Not used (Open) – Ground terminal LOCK Not used (Open) Spindle motor servo control signal output...
Page 55
HCD-GNX600 Pin No. Pin Name Description AVSS3 – Ground terminal CLTV Multiplier VCO1 control voltage input FILO Master PLL (slave = digital PLL) filter signal output FILI Master PLL filter signal input Master PLL charge pump signal output AVDD5 –...
Page 56
HCD-GNX600 Pin No. Pin Name Description EXCK Not used (Open) XRST System reset signal input from M30622MEP SYSM Muting signal input (Connected to ground) DATA Serial data input from M30622MEP – Ground terminal XLAT Latch signal input from M30622MEP CLOCK Serial data transfer clock input from M30622MEP –...
Page 57
HCD-GNX600 Ver. 1.1 • IC401 M30622MGP-A54FPU0 SYSTEM CONTROL (MAIN BOARD) Pin No. Pin Name Description BD-RST Reset signal output to the digital signal processor ( “L”:reset) CD-DATA-OUT Serial data output to the digital signal processor XLAT Serial data latch pulse output to the digital signal processor...
Page 58
HCD-GNX600 Pin No. Pin Name Description LM-F Loading motor control signal output to the CD mechanism deck LM-R Loading motor control signal output to the CD mechanism deck LED-ILLUMINATION-1 Dynamic LED drive signal output to the ILLUMINATION 1st indicator and 2nd...
Page 59
HCD-GNX600 Pin No. Pin Name Description AVSS Ground terminal (for A/D conversion) AD-KEY-1 Key input terminal (A/D input) VREF A/D Converter reference voltage input terminal (+3.3V) AVCC Power supply terminal (+3.3V) (for A/D conversion) MAIN ON/OFF Main power on/off control signal output (“H”:power on)
Page 60
HCD-GNX600 • IC403 BH2210FV-E2 (SIGNAL IN/OUT CONTROL) (MAIN BOARD) Pin No. Pin Name Description CTLIO Input/output mode select port (Fixed at "H") RESET Reset signal input Serial data clock input LATCH Serial data latch input TC-MUTE Tape playback muting on/off control signal output ( "H":muting on)
HCD-GNX600 SECTION 8 EXPLODED VIEWS NOTE: • -XX, -X mean standardized parts, so they may • Hardware (# mark) list and accessories are The components identified by mark 0 or have some differences from the original one. given in the last of this parts list.
HCD-GNX600 8-3. CHASSIS SECTION not supplied not supplied supplied supplied F1100 not supplied not supplied not supplied not supplied Ref. No. Part No. Description Remarks Ref. No. Part No. Description Remarks 2-630-050-01 +BVTT 3X6 (SUMITITE) 0 108 1-829-259-11 CORD, POWER (AUS)
HCD-GNX600 Ver. 1.1 SECTION 9 ELECTRICAL PARTS LIST NOTE: • Due to standardization, replacements in the • COILS The components identified by mark 0 uH: µH parts list may be different from the parts or dotted line with mark 0 are critical specified in the diagrams or the components •...
Page 67
HCD-GNX600 Ver. 1.1 Ref. No. Part No. Description Remarks Ref. No. Part No. Description Remarks 1-216-825-11 METAL CHIP 2.2K 1/10W C174 1-164-360-11 CERAMIC CHIP 0.1uF 1-216-845-11 METAL CHIP 100K 1/10W C181 1-164-360-11 CERAMIC CHIP 0.1uF 1-216-864-11 SHORT CHIP C182 1-164-360-11 CERAMIC CHIP 0.1uF...
Page 68
HCD-GNX600 DRIVER Ref. No. Part No. Description Remarks Ref. No. Part No. Description Remarks < TRANSISTOR > R409 1-216-809-11 METAL CHIP 1/10W R410 1-216-809-11 METAL CHIP 1/10W 6-551-120-01 TRANSISTOR 2SA2119K R411 1-216-809-11 METAL CHIP 1/10W < RESISTOR > R412 1-216-809-11 METAL CHIP...
HCD-GNX600 REVISION HISTORY Clicking the version allows you to jump to the revised page. Also, clicking the version at the upper right on the revised page allows you to jump to the next revised page. Ver. Date Description of Revision 2006.04...