Table of Contents
Advertisement
76 CAP ET
O
77 CYL ET
O
78 P.FAIL (L)
I
79 S-REEL PULSE
I
80 T-REEL PULSE
I
81 VSS
82 EX.FF/REW (L)
I/O
83 UNLOADING (H)
O
84 LOADING (H)
O
85 SQPB (H)
I
86 FG.AMP.OUT
O Capstan FG Amp Signal Output terminal.
87 FG.AMP.IN
I
88 GND(A)
- Analog GND.
89 MESECAM (H)
I
90 CYL PFG
I
91 OREF
O Analog Amp 1/2 Vdd Ref Power Output Terminal
92 IREF
I
93 VSS
94 CTL HEAD (-)
I/O Control head ( - )side Input/Output Terminal.
95 CTL HEAD (+)
I/O Control head ( + )side Input/Output Terminal.
96 CTL AMP REF
I
97 PB CTL OUT
O Control Amp Output terminal.
98 5V (A)
- Analog Amp Power Supply Terminal
99 5V (AD)
- AD/8 bit DA Ref Power Supply Terminal.
100 T.S. CURVE
I
Capstan motor control voltage supply terminal
When higher than Drive Reference Voltage: Accelerated
When lower than Drive Reference Voltage : Current off
Cylinder Motor Control Voltage Supply terminal
When higher than Driver Reference Voltage: current off
When lower than Driver Reference Voltage: accelerated
However, during Cylinder Off, Max value of decelerated Voltage is as follow.
Normal Control : 3.150V
Cylinder Off: 5.000V
Power Failure Detection Input terminal
Input = "L", Power Failure Mode
Pulse Input terminal from reel sensor
Pulse Input terminal from reel sensor
GND
Control Signal Filter Selection Terminal during FF/REW
Control spec shall comply with Mecha FFREW(Hi-Z) output timing.
Set Input when deck enters FF/RRW mode.
During Stop, due to FF/REW stopping process, switch over to STOP3 first, then
STOP is canceled.
Deck
STOP
FF/RE
Position
STOP
PNO
00
21
EX.FF/REW(
Lo
However, when starting FF/REW, Filter C addition will be required until it become
high speed. Then monitor the CTL Amp Gain(COH bit 0-2) setting value. When 5(
=60dB) or 7(=70dB), compulsorily, output = Low.
Loading Motor Control terminal
shall comply with R4 mecha control spec.
Loading Motor Control terminal
shall comply with R4 mecha control spec.
The distinction results wheter S-VHS or VHS of the playback tape is input in VV
mode.
*Low is input: VHS tape playback.
*High is input: S-VHS tape playback.
Note: When the MESECAM (H) terminal receives "High", above result is invalidated
and the tape is judged to VHS tape playback.
Capstan FG signal Input Terminal.
Distinction terminal for the VDIEO SYSTEM.
1.In the VV mode.
*High is input: Playback of a MESECAM recorded tape.
*Low is input: Playback of other than MESECAM recorded tape.
2.In the EE mode.
*High is input: Receiving a SECAM broadcast, or SECAM signal is input.
Cylinder P.FG signal Input Terminal.
Analog Amp 1/2 Vdd Ref Power Input Terminal
Unused terminal. Connected to GND.
Control Amp Ref Capacitor Connection Terminal
Input terminal for "S-Curve" of Tuner AFC at channel selecting.
STOP
FF/RE
STO
PLA
00
26
27
28
00
Hi-Z
Lo
53
NV-VP60GL / NV-VP60GC / NV-VP60GCS
High
High
PWM=
Low
PWM=
0V
0V
Low
Low
PWM=
Low
PWM=
5.000V
5.000V
In
In
In
In
In
In
In
In
In
Low
Low
Low
Low
Low
Low
Low
Low
Low
Low
Low
Low
In
In
In
Out
Out
Out
In
In
In
-
-
-
In
In
In
In
In
In
Out
Out
Out
In
In
In
-
-
-
In/Out
In/Out
In/Out
In/Out
In/Out
In/Out
In
In
In
Out
Out
Out
-
-
-
-
-
-
In
In
In
- Quick Links:
- General Description
- Operating Instructions
Hide quick links:
Advertisement
Table of Contents
