Maintenance; Optional Accessories; Operation - Makita 6704D Instruction Manual

Number on adjusting
ring
1
2
3
4
5
006402
Example
35 Kg·cm of fastening torque can be obtained when the
number 2 is aligned to the red mark.
NOTE:
• Always tighten the two screws to secure the adjusting
ring after adjusting the fastening torque.
• The fastening torque may differ depending upon the
kind of screws, the type of materials to be fastened,
etc. Before starting your job, always perform a test
operation to verify the adequate fastening torque.
ASSEMBLY
CAUTION:
• Always be sure that the tool is switched off and the
battery cartridge is removed before carrying out any
work on the tool.
Installing or removing socket
For tool with square drive
Use 9.5 mm square drive socket with a hole for detent pin
which is available on the market (Note: Use 6.35 mm
square drive socket when using the tool with 6.35 mm
drive.) (Fig. 5)
To install the socket, depress the detent pin on the square
drive with your finger and push the socket onto the square
drive until the detent pin is inserted into the hole in the
socket. (Fig. 6)
To remove the socket, depress the detent pin with a small
hand tool and pull off the socket.
For tool with round drive (Fig. 7)
Use a bit with Form C 6.3 shank which is available on the
market. The bit can be inserted directly into the round
drive and held in place.
To install the bit, push it firmly into the round drive. To
remove the bit, grasp it with a pair of pliers and pull it out
of the round drive. Sometimes, it helps to wiggle the bit
with the pliers as you pull.

OPERATION

The proper fastening torque may differ depending upon
the kind or size of screws, the type of materials to be
fastened, the condition of the threads, etc. Before starting
your job, always perform a test operation to verify
adequate fastening torque.
Hold the tool firmly with both hands whenever possible
and place the socket over the or nut. Then turn the tool
on. As soon as the bolt or nut becomes tight, the clutch
will cut in and motor will stop automatically. Release the
switch trigger.
6
Fastening torque to be
obtained
20 Kg·cm
35 Kg·cm
48 Kg·cm
60 Kg·cm
80 Kg·cm
When fastening tool screws, use proper screwdriver bit. It
is commonly available on the market. (Fig. 8)
For 6706D
When the battery capacity decreases to a certain level,
the motor will not start even if you press the switch trigger.
This mechanism prevents poor fastening caused by
battery voltage-drop. Charge the battery cartridge to
resume operation.
NOTE:
• Always use the correct size socket for bolts and nuts.
An incorrect size will result in inaccurate and
inconsistent fastening torque and/or damage to the bolt
or nut.
• Hold the tool with its square drive pointed straight at the
bolt or nut, or the bolt or nut will be damaged.
• If the motor will not start even after you pull the trigger,
release the trigeer. Then pull the trigger again after
turning the socket slightly with your fingers.

MAINTENANCE

CAUTION:
• Always be sure that the tool is switched off and the
battery cartridge is removed before attempting to
perform inspection or maintenance.
• Never use gasoline, benzine, thinner, alcohol or the
like. Discoloration, deformation or cracks may result.
To maintain product SAFETY and RELIABILITY, repairs,
any other maintenance or adjustment should be
performed by Makita Authorized Service Centers, always
using Makita replacement parts.

OPTIONAL ACCESSORIES

CAUTION:
• These accessories or attachments are recommended
for use with your Makita tool specified in this manual.
The use of any other accessories or attachments might
present a risk of injury to persons. Only use accessory
or attachment for its stated purpose.
If you need any assistance for more details regarding
these accessories, ask your local Makita Service Center.
• Various type of Makita genuine batteries and chargers
• Plastic carrying case
NOTE:
• Some items in the list may be included in the tool
package as standard accessories. They may differ from
country to country.