Noise/Vibration Information; Declaration Of Conformity; Battery Charging - Bosch GKS 10,8 V-LI Original Instructions Manual

OBJ_BUCH-2006-001.book Page 17 Tuesday, October 8, 2013 10:38 AM
Battery
Permitted ambient tempera-
ture
– when charging
– during operation*
– during storage
Recommended batteries
* Limited performance at temperatures <0 °C

Noise/Vibration Information

Measured sound values determined according to EN 60745.
Typically the A-weighted noise levels of the product are:
Sound pressure level 90 dB(A); Sound power level
101 dB(A). Uncertainty K =3 dB.
Wear hearing protection!
Vibration total values a (triax vector sum) and uncertainty K
h
determined according to EN 60745:
2
Cutting wood: a =2.5 m/s , K=1.5 m/s
h
The vibration level given in this information sheet has been
measured in accordance with a standardised test given in
EN 60745 and may be used to compare one tool with anoth-
er. It may be used for a preliminary assessment of exposure.
The declared vibration emission level represents the main ap-
plications of the tool. However if the tool is used for different
applications, with different accessories or insertion tools or is
poorly maintained, the vibration emission may differ. This
may significantly increase the exposure level over the total
working period.
An estimation of the level of exposure to vibration should also
take into account the times when the tool is switched off or
when it is running but not actually doing the job. This may signif-
icantly reduce the exposure level over the total working period.
Identify additional safety measures to protect the operator
from the effects of vibration such as: maintain the tool and the
accessories, keep the hands warm, organisation of work pat-
terns.

Declaration of Conformity

We declare under our sole responsibility that the product de-
scribed under "Technical Data" is in conformity with the fol-
lowing standards or standardisation documents: EN 60745
according to the provisions of the directives 2009/125/EC
(Regulation 1194/2012), 2011/65/EU, 2004/108/EC,
2006/42/EC.
Technical file (2006/42/EC) at:
Robert Bosch GmbH, PT/ETM9,
D-70745 Leinfelden-Echterdingen
Henk Becker Helmut Heinzelmann
Executive Vice President Head of Product Certification
Engineering PT/ETM9
Robert Bosch GmbH, Power Tools Division
D-70745 Leinfelden-Echterdingen
Leinfelden, 22.08.2013
Bosch Power Tools
Assembly

Battery Charging

 Use only the battery chargers listed on the accessories
°C 0...+45
page. Only these battery chargers are matched to the lith-
°C –20...+50
ium ion battery of your power tool.
°C –20...+60
Note: The battery is supplied partially charged. To ensure full
GBA 10,8V x,xAh O–.
capacity of the battery, completely charge the battery in the
battery charger before using your power tool for the first time.
The lithium ion battery can be charged at any time without re-
ducing its service life. Interrupting the charging procedure
does not damage the battery.
The lithium ion battery is protected against deep discharging
by the "Electronic Cell Protection (ECP)". When the battery is
empty, the machine is switched off by means of a protective
circuit: The inserted tool no longer rotates.
 Do not continue to press the On/Off switch after the
machine has been automatically switched off. The bat-
2
.
tery can be damaged.
Observe the notes for disposal.
Removing the battery
The battery 1 is equipped with two locking levels that should
prevent the battery from falling out when pushing the battery
unlocking button 2 unintentionally. As long as the battery is
inserted in the power tool, it is held in position by means of a
spring.
To remove the battery 1, press the battery unlocking button 2
and pull the battery out of the power tool toward the rear.
Do not exert any force.
Battery Charge-control Indication
The three green LEDs of the battery charge-control indicator
15 indicate the charge condition of the battery 1. For safety
reasons, it is only possible to check the status of the charge
condition when the machine is at a standstill.
Press the On/Off switch 4 halfway or completely through to
indicate the charge condition.
LED
Continuous lighting 3 x green
Continuous lighting 2 x green
Continuous lighting 1 x green
Flashing light 1 x green
When no LED lights up after pressing the On/Off switch 4, the
battery is defective and must be replaced.
Mounting/Replacing the Saw Blade
 Before any work on the power tool, remove the battery.
 When mounting the saw blade, wear protective gloves.
Danger of injury when touching the saw blade.
 Only use saw blades that correspond with the charac-
teristic data given in the operating instructions.
 Do not under any circumstances use grinding discs as
the cutting tool.
English | 17
Capacity
2/3
1/3
<1/3
Reserve
1 619 P11 365 | (8.10.13)