Information On Disposal; Environmental Information - Sharp MX-M654N Start Manual

Do not remove the machine casing.
High-voltage parts inside the machine may cause electrical
shock.
Do not make any modifications to this machine.
Doing so may result in personal injury or damage to the
machine.
Do not use a flammable spray to clean the machine.
If gas from the spray comes in contact with hot electrical
components or the fusing unit inside the machine, fire or
electrical shock may result.
If you notice smoke, a strange odor, or other abnormality,
do not use the machine.
If used in this condition, fire or electrical shock may result.
Immediately switch off the main power and remove the power
plug from the power outlet.
Contact your dealer or nearest authorised service
representative.
If a thunder storm begins, switch off the main power and
remove the power plug from the outlet to prevent
electrical shock and fire due to lightning.
If a piece of metal or water enters the machine, switch off
the main power and remove the power plug from the
power outlet.
Contact your dealer or nearest authorised service
representative. Using the machine in this condition may result
in electrical shock or fire.
CAUTION
Do not look directly at the light source.
Doing so may damage your eyes.
Do not block the ventilation ports on the machine. Do not
install the machine in a location that will block the
ventilation ports.
Blocking the ventilation ports will cause heat to build up in the
machine, creating a risk of fire.
The fusing unit and paper exit area are hot. When
removing a misfeed, do not touch the fusing unit and
paper exit area. Take care not to burn yourself.
When loading paper, removing a misfeed, performing
maintenance, closing the front and side covers, and
inserting and removing trays, take care that your fingers
are not pinched.
Caution
For a complete electrical disconnection, pull out the main plug.
The socket-outlet shall be installed near the equipment and shall be
easily accessible.
Shielded interface cables must be used with this equipment to
maintain compliance with EMC regulations.
A Cable of 10 m or less is preferable.
The equipment should be installed near an accessible socket outlet for
easy disconnection. Each instruction also covers the optional units
used with these products.
EMC (this machine and peripheral
devices)
WARNING:
This is a Class A product. In a domestic environment this product may
cause radio interference in which case the user may be required to
take adequate measures.
Notice for users in the UK
MAINS PLUG WIRING INSTRUCTIONS
The mains lead of this equipment is already fitted with a mains plug
which is either a non-rewireable (moulded) or a rewireable type.
Should the fuse need to be replaced, a BSI or ASTA approved fuse to
BS1362 marked or
removed from the plug must be used.
Always refit the fuse cover after replacing the fuse on the moulded
plug. Never use the plug without the fuse cover fitted.
In the unlikely event of the socket outlet in your home not being
compatible with the plug supplied either cut-off the moulded plug (if
and of the same rating as the one
this type is fitted) or remove by undoing the screws if a rewireable plug
is fitted and fit an appropriate type observing the wiring code below.
DANGER: The fuse should be removed from the cut-off plug and the
plug destroyed immediately and disposed of in a safe manner. Under
no circumstances should the cut-off plug be inserted elsewhere into a
13A socket outlet as a serious electric shock may occur.
To fit an appropriate plug to the mains lead, follow the instructions
below:
IMPORTANT: The wires in this mains lead are coloured in accordance
with the following code:
GREEN-AND-YELLOW:
BLUE:
BROWN:
As the colours of the wires in this mains lead may not correspond with
coloured markings identifying the terminals in your plug, proceed as
follows:
The wire which is coloured GREEN-AND-YELLOW must be
connected to the terminal in the plug which is marked with the letter E,
or by the safety earth symbol
yellow.
The wire which is coloured BLUE must be connected to the terminal
which is marked with the letter N or coloured black.
The wire which is coloured BROWN must be connected to the
terminal which is marked with the letter L or coloured red.
If you have any doubt, consult a qualified electrician.
WARNING: THIS APPARATUS MUST BE EARTHED.
Safety data sheet
The SDS (Safety Data Sheet) can be viewed at the following URL
address:
http://www.sharp-world.com/corporate/eco/env-info/sds/index.html

Information on Disposal

Information on the Disposal of this
Equipment and its Batteries
IF YOU WISH TO DISPOSE OF THIS
EQUIPMENT, DO NOT USE THE
ORDINARY WASTE BIN, AND DO NOT
PUT THEM INTO A FIREPLACE!
Used electrical and electronic equipment
and batteries should always be collected
and treated SEPARATELY in accordance
with local law.
Separate collection promotes an
environment-friendly treatment, recycling
of materials, and minimizing final disposal
of waste. IMPROPER DISPOSAL can be
harmful to human health and the
environment due to certain substances!
Take USED EQUIPMENT to a local,
usually municipal, collection facility, where available.
This equipment contains a BATTERY which cannot be removed by the
user. For battery exchange, please contact your dealer.
If in doubt about disposal, contact your local authorities or dealer and
ask for the correct method of disposal.
ONLY FOR USERS IN THE EUROPEAN UNION, AND SOME
OTHER COUNTRIES; FOR INSTANCE NORWAY AND
SWITZERLAND: Your participation in separate collection is requested
by law.
The symbol shown above appears on electrical and electronic
equipment (or the packaging) to remind the users of this.
If the equipment has been used for BUSINESS PURPOSES, please
contact your SHARP dealer who will inform you about take-back. You
might be charged for the costs arising from take-back. Small
equipment (and small quantities) might be taken back by your local
collection facility. For Spain: Please contact the established collection
system or your local authority for take-back of your used products.

Environmental information

Please read this part carefully. It will help you to reduce your
impact on the environment and help you to reduce your costs at
the same time.
Saving paper
1. The automated duplex printing function is for printing both sides of
paper automatically without turning over the paper manually. If the
machine is equipped with the automated duplex printing function,
set up your print settings on your computer to automatically print
4
Earth
Neutral
Live
, or coloured green or greenand-
Users from PRIVATE
HOUSEHOLDS are
requested to use
existing return
facilities for used
equipment. Return is
free of charge.