Advertisement
3. 3. 3. 3. AP Configuration with SMT User Interface
AP Configuration with SMT User Interface
AP Configuration with SMT User Interface
AP Configuration with SMT User Interface
3 3 3 3 - - - - 1. 1. 1. 1. Conf
Configuring AP
iguring AP with
Conf
Conf
iguring AP
iguring AP
STEP– – – – 1 1 1 1 . . . . Power on the AP
STEP
STEP
STEP
Power on the AP
Power on the AP
Power on the AP
1.Connect power supply to PoE injector with the AC power cord provided as shown in the above
diagram. The yellow POWER
POWER LED on the PoE will be on when the PoE has adequate power supply.
POWER
POWER
2.Connect The AP to POWE
Cable provided. The red ACTIVE
3.Connect DATA IN
DATA IN port on the PoE injector with Ethernet cable to the LAN that the AP associates
DATA IN
DATA IN
with.
STEP– – – – 2 2 2 2 . Verify IP address setting
STEP
STEP
STEP
. Verify IP address setting
. Verify IP address setting
. Verify IP address setting
Configure the network settings on your PC to obtain an IP address. Computer uses IP addresses to
communicate with each other across a network, such as a LAN.
192.168.1.1
192.168.1.1
so the PC needs to be set in the same net scope to access AP with Telnet.
192.168.1.1
192.168.1.1
1.Go to Control Panel
Control Panel of your PC and double-click Network
Control Panel
Control Panel
2.Right click Local
Local
Local Area
Local
Area Connection
Area
Area
3.Select TCP/IP
TCP/IP for the applicable Ethernet adapter and click Prope
TCP/IP
TCP/IP
4.Click the IP Address
IP Address tab page, select USE the following IP address
IP Address
IP Address
192.168.1.2 2 2 2
192.168.1.
to
192.168.1.254
92.168.1.254
192.168.1.
192.168.1.
92.168.1.254
92.168.1.254
Mask, then click OK
Mask
Mask
Mask
OK button.
OK
OK
STEP– – – – 3 3 3 3 . . . . Connect the AP by
STEP
STEP
STEP
Connect the AP by
Connect the AP by
Connect the AP by telnet
After having the correct connection, start the telnet session to
" " " " 0000
0000" " " "
0000
0000
and press ENTER on your keyboard to enter the main menu. The system menu tree (SMT) will
appear on your terminal software as shown below.
Please refer to the user manual for detailed description of each selection item.
with Telnet
Telnet
with
with
Telnet
Telnet
POWER & DATA OUT
R & DATA OUT port on the PoE with MIL-C-5015 IP67 Cat-5 Ethernet
POWE
POWE
R & DATA OUT
R & DATA OUT
ACTIVE
ACTIVE LED indicates if the AP has successfully powered-on.
ACTIVE
Connection and select Properties
Connection
Connection
USE the following IP address, type an address between
USE the following IP address
USE the following IP address
(192.168.1.1 is for the AP) for IP Address
telnet
telnet
telnet
The default IP address of the AP is
The default IP address of the AP is
The default IP address of the AP is
The default IP address of the AP is
Network C C C C onnections
Network
Network
onnections icon.
onnections
onnections
Properties.
Properties
Properties
Properties
rties.
Prope
Prope
rties
rties
IP Address and 255.255.255.0
IP Address
IP Address
192.168.1.1
192.168.1.1.
192.168.1.1
192.168.1.1
( ( ( ( Note:
Note: The Web UI is ID: admin / PW: password
The Web UI is ID: admin / PW: password. . . . ) ) ) )
Note:
Note:
The Web UI is ID: admin / PW: password
The Web UI is ID: admin / PW: password
3
255.255.255.0 for Subnet
Subnet
255.255.255.0
255.255.255.0
Subnet
Subnet
Enter the default password
Enter the default password
Enter the default password
Enter the default password
V1.0
Advertisement
